AzureWave AW-AM510-uSD Adapter Board With Wi-Fi-BT Module User Guide

June 6, 2024
AzureWave

AzureWave AW-AM510-uSD Adapter Board With Wi-Fi-BT Module User Guide
AzureWave AW-AM510-uSD Adapter Board With Wi-Fi-BT
Module

The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWave.

Revision History

Version| Revision Date| Description| Initials| Approved
---|---|---|---|---
A| 2021/1/26| l  Initial Version| Roger Liu| N.C. Chen
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |

Introduction

AzureWave provides uSD-1212 adapter board with Wi-Fi/BT module solutions for NXP i.MX RT and i.MX6/7/8 Evaluation Kits. The uSD-1212 adapter board supports AW-AM510 (with NXP IW416UK) Wi-Fi combo BT module solutions.

  • WiFi through uSD interface
  • BT through UART interface
    Main chip| AzureWave Module| uSD Adaptor Board
    ---|---|---
    NXP IW416UK| AW-AM510| AW-AM510-uSD
  1. Supported I/O to host
    • Micro SD (uSD) interface for Wi-Fi.
    • Arduino headers for Bluetooth through UART interface.
    • FFC connector for UART and other control signal.
    • Embedded UART-to-USB IC as an option for UART.
    • Other debug and power interface.
  2. Supported I/O signal level
I/O\voltage level 1.8V 3.3V
SDIO(3.0/2.0) V V
UART N/A V
  1. Supported RF standards
    ** Model \ Standards| Wi-Fi*| *BT
    ---|---|---
    AW-AM510| 1×1 Wi-Fi 4 (2.4/5GHz)| 5.1

The information contained herein is the exclusive property of AzureWave and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of AzureWav

AW-AM510-uSD

  1. Block Diagram
    Block Diagram

  2. HW Description
    VIO for SDIO voltage level options

    • For 3.3V supply, please connect J4 (2-3).
    • For 1.8V supply, please connect J4 (1-2).
      3.3V power source is configured from SDIO connector as default.
      HW Description

UART signal is configured from FFC connector at BOT side as default.
By using headers for Bluetooth through UART interface

  • UART_RTS: J7 (pin 3) or J10 (pin 6)
  • UART_TXD: J8 (pin 1) or J10 (pin 4)
  • UART_CTS: J7 (pin 4) or J10 (pin 8)
  • UART_RXD: J8 (pin 2) or J10 (pin 2)
    HW Description

PCM signal is configured from FFC connector at BOT side as default.
By using headers for PCM interface

  • PCM_IN: J11 (pin 1)
  • PCM_OUT: J11 (pin 2)
  • PCM_SYNC: J11 (pin 3)
  • PCM_CLK: J11 (pin 4)

Schematics

Schematics
Schematics
Schematics

Placement

Placement

EVB Kits Contents

Content Description
**** AW-AM510-uSD
**** 75mm, 20 contacts, 0.5mm pitch FFC Cable




| PIFA Antenna

  • Radiation: Directional
  • 3D Peak Gain:
    • n  2.98dBi (2.4~2.5GHz)
    • n  5.16dBi (4.9~5.9GHz)
  • Polarization: Linear Vertical
  • Connector: IPEX-4 Compatible
  • Operating Temp: -20℃ ~ +65℃
  • Storage Temp: -30℃ ~ +75℃

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

AzureWave User Manuals

Related Manuals