joyami B0BCJR4VXN Smart Blender User Manual

Smart Blender
Operation Manual

Please read this operation manual carefully before starting the product, and save it properly for future use.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

• Read all instructions.
• To protect against risk of electrical shock do not put cord, plugs, portable appliances in water or other liquid.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
• Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
• Avoid contacting moving parts.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on examination, repair, or adjustment.
• The use of attachments, including canning jars, not recommended by the manufacturer may cause a risk of injury to p ersons.
• Do not use outdoors. Household Use Only.
• Do not let cord hang over edge of table or counter, or touch hot surfaces. Do not place on or near a hot gas or electric burner, or in a heated oven. Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons or damage to the blender. A scraper may be used but must be used only when the blender is not running (does not apply to an acceptable scraper integral with the appliance).
• Blades are sharp. Handle carefully.
• Always operate blender with cover in place.
• When blending hot liquids or operating in the heating mode, remove center piece of two-piece cover.
• Allow to cool before assembling or disassembling parts and before cleaning the appliance.
• Do not touch surfaces that may be hot. Use handles or knobs provided. Remove plug from outlet when the appliance is not in use, before putting on or taking off parts, and before cleaning. Allow to cool before handling.
• Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
• Where applicable, always attach plug to appliance and check that the control is OFF before plugging cord into wall outlet. To disconnect, turn the control to OFF, then remove plug from all outlet.
• Do not use appliance for other than intended use.
• Avoid contacting moving parts.

SAVE THIS INSTRUCTIONS

Cleaning & maintenance

• Do not immerse the blender in water or splash it with water.
• Do not use steel wool or other hard objects to clean the heating plate.
• Use only soft cloths for cleaning.
• If the blender will not be used for an extended period of time, unplug the power cord and take appropriate measures to protect the blender from moisture, dust, and household pests.
• Ensure that the power cord is disconnected and wait until the jar cools down before cleaning.
• The table surface the blender is placed on must be regularly cleaned of grease.
• Please rinse the jar’s interior and accessories with clean water before wiping them dry. The blades are sharp, so please be careful when cleaning toavoid injury emptying the bow.

Precautions on Electric Power

• Do not use any power supply other than 120V to avoid fire and electrical shocks.
• Always unplug the blender by holding the powerplug to avoid fire or electrical shocks.
• Do not plug or unplug the power cord when your hands are wet to avoid injury and electrical shocks.
• Use only power sockets with a rated current above 10 A.
• If the power cord is damaged or broken, it must be replaced by the manufacturer or after-sales service department to avoid safety hazards.
• Do not use other power cord extenders or parts not approved by manufacturer or maintenance department when repairing.
• To avoid the risk of fire, do not use low-quality power strips with this product.
• Only use the blender on the base provided.
• Always unplug the blender before cleaning, assembling or disassembling, or after useing.
• Make sure that the blender is powered off before moving the base.

In Use

• Do not add water over the maximum level, or else the water will overflow or spray out and cause burns or other accidents.
• Idling or overloading is strictly prohibited.
• Do not move the blender or touch any running parts when in use to avoid accidents.
• Do not heat without any food or water inside.
• Do not move the lid and lid plug when in use.
• Do not allow any liquid to get on the pin connector.
• There will be residual heat after heating element works.
• The surface of the jar and lid will be hot while heating, so please do not touch them while in use.

Environment

• Steam and heat may damage, discolor or deform your walls and furniture, so keep the product preferably during use 30 cm away from any walls and furniture.
• When using the blender in a kitchen cabinet, etc., please ensure that the place is well ventilated.

Product Description

Accessories

Tip: The illustrations of product, component and user interface are all schematic diagrams for reference only in the manual.
Due to possible upgrade of the product, there may be differences between the actual product and the schematic diagram included herein. The actual product shall prevail.

About Use

Start to Use
When joyami Smart Blender is powered on for the first time, it enters the Wi- Fi setting interface. Press the main rotary knob and select Enable/Disable Wi- Fi. At this moment, rotate the main rotary knob to Enable or Disable Wi-Fi, press the main rotary knob to
confirm and return to “Press & hold to start” interface to start the blender. If no operation is made for 30sec, the default result will be “No” (Wi-Fi is disabled).

Turn ON/OFF and Pause

1. Turn On
   Every time joyami Smart Blender is powered on, the screen will display “Press & hold to start”. At this moment, press and hold the main rotary knob for 2 sec to turn on the device. The first mode will be displayed when joyami Smart Blender is powered on and turned on for the first time. In the standby state, if no operation is made for 10min, the screen will enter the Always on Display (AOD) state.

2. Turn Off
   joyami Smart Blender may be turned off after the main rotary knob is pressed and held for 2sec in any state, except in the Press & hold to clean mode. In the non-working state (standby, lifting jar, and opening jar plug), if no operation is made for 10min, the screen will enter the Always on Display (AOD) state.

3. Pause
   In the working state, if the main rotary knob is pressed once, joyami Smart Blender will pause working; if the main rotary knob is pressed again, it will resume working as set in the last operation.
   Tip: Depending on functions, joyami Smart Blender has different default pause durations, namely, 2 min for hot drinks and 1 min for cold drinks. The pause state is in the countdown mode.

Connect with Mi Home App
This product works with Mi Home app. Control your device, and interact it and other smart home devices with Mi Home app.
Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already.
Or search “Mi Home” in the app Store to download and install it.
Open Mi Home app, tap “+” on the upper right, and then follow prompts to add your device.
Tip: The version of Mi Home app might have been updated, please follow the instructions based on the current app version.

https://home.mi.com/do/home.html?f=xz&p=8627

Wi-Fi Status

Operation Mode| Status Display
Wi-Fi is disabled| The Wi-Fi icon is blinking
Wi-Fi is enabled| The Wi-Fi icon stays on

Tip: When Wi-Fi is disabled, the Wi-Fi icon is in the blinking state.

Operating Guide

1. Take out joyami Smart Blender, clean the lid plug, lid and whisk with water, and the outside surface of the main base with soft wet cloth. Do not immerse any working electrical components such as the main base, jar, and power cord in water, not spay water on any part containing electric component such as the main base and jar base.
2. Clean the ingredients, cut them into 3cm chunks and put the chunks in the jar.
3. Install the lid plug on the lid, turn the lid clockwise and lock it with the jar tightly.
4. Place the jar correctly on the main base, and align the small triangle below the handle with the alignment line on the main base. Make sure to place the main base on a table surface.
5. After powering on joyami Smart Blender, rotate the main rotary knob to switch over its functions. When switching to the required function, press the main rotary knob to enter the cooking state.

Cleaning & Maintenance

Cleaning

1. Be careful of scald caused by residual heat. Please wait until the jar fully cools before cleaning.
2. After the drink is made, cools and is poured out, please immediately add clean water in the jar and operate the “Press & hold to clean” mode for several times to clean the jar better.
3. After powering off joyami Smart Blender, clean the outside surface of the main base with soft wet cloth. Do not immerse any working electrical components such as the main base, jar, and power cord in water. Dot not spay water on any part containing electric component such as the main base and jar base.
4. When cleaning, rinse the jar interior and accessories with clean water, and wipe off residual water. The blades are very sharp. Be careful with the blades to avoid cuts during cleaning.
5. Do not use abrasive detergent or corrosive liquid (such as gasoline and acetone) to clean the device.
6. If any part of joyami Smart Blender is strained by fruit/vegetable juice or other drinks, add several drops of edible oil to wipe the strains before rinsing it with clean water to better remove the stains. Please wipe off residual water after rinsing any parts with  clean water.
7. If any residues in the jar form a hard block that is difficult to remove, please add an appropriate amount of water to soak it first, and then rinse and wipe it off after it is softened.
8. When the bottom of the heating plate is not clean after several times of cleaning and accumulated with any residual adhesive layer on it, soak the bottom with clean water for a period of time, then dip white vinegar with soft cloth, and gently wipe the bottom with the cloth. Be careful of the blades so as to avoid cuts when wiping them. Do not wipe the device after it is powered on.

Maintenance

1. joyami Smart Blender should be used frequently to keep its motor dry.
2. If the device is not used for a long time, please keep it in a dry and ventilated place to prevent the motor from being affected by moisture.

Function Instruction

rotary knob displays “Jam”. Press the main rotary knob to start making jam, or rotate the main rotary knob to select Smooth soup, Chunky soup or Soy milk, press the main rotary to start making the chosen one.
Tip 1: You may select a Timer program. joyami Smart Blender will keep warm by default after the cooking program is completed. If cooking is paused and not resumed after 2 min during the working period, the cooking program will be canceled automatically.
Tip 2: After the device starts working, if the main rotary knob is pressed, it will pause the cooking, and if pressed again, it will resume the cooking. After the cooking is paused, if the Cancel button is pressed, the device will exit from the cooking.
Smoothie Fruit & vegetable juice| After turning on the device, the main rotary knob displays “Jam”. Rotate the main rotary knob to select “Smoothie”, “Fruit & vegetable juice” or “Milkshake”, and press the main rotary knob to start making the chosen drink.
Tip 1: You are not allowed to select a Timer program. The device will cancel the cooking program automatically if cooking is paused and not resumed after 1 min during the working period.
Tip 2: After the device starts working, if the main rotary knob is pressed, it will pause the operation, and if pressed again, it will resume the operation. After the operation is paused, if the Cancel button is pressed, the device will exit from the operation.
Milkshake Press & hold to clean| After turning on the device, the main rotary knob displays “Jam”. Rotate the main rotary knob to select the “Press & hold to clean” mode, add the ingredients or clean water in the jar, press the main rotary knob to start operating the chosen operation.
Tip 1: If ingredient is not fully blended, select “Press & hold to clean” function to blend for a short time again.
Tip 2: Select “Press & hold to clean” function to clean the jar.
Manual| After turning on joyami Smart Blender, the main rotary knob displays “Jam”. Rotate the main rotary knob to select the “Manual “mode, press the main rotary knob, and then rotate the main rotary knob to select a revolving speed.
Tip: After the device starts working, if the main rotary knob is pressed, it will pause the operation, and if pressed again, it will resume the operation. After the operation is paused, if the Cancel button is pressed, the device will exit from the operation.
Settings| 1. If Wi-Fi is enabled in joyami Smart Blender, rotate the main rotary knob to select the Wi-Fi interface on the Settings screen, and press the main rotary knob to reset or disable Wi-Fi.
2. If Wi-Fi is disabled in joyami Smart Blender, rotate the main rotary knob to select the Wi-Fi interface on the Settings screen, and press the main rotary knob to enable Wi-Fi.
Tip: During the enabling or disabling Wi-Fi process, if no operation is made for 30 sec, the last option is chosen and back to the Setting interface by default.

Recipe

Tip: When using joyami Smart Blender for continuously making fruit & vegetable juice, the working time should not exceed 2 min each time, and the total working time should not exceed 6 min. During the operation, if the main base is overheated, stop the operation for about 20 min, and resume it after the main base cools down.
Smooth soup| 38min| 1pc potato (about 220 g), 10 g cashew nut, 50 g white mushroom, 2 g salt, an appropriate amount of white pepper powder, 720 ml water
Chunky soup| 35min| 1pc potato (about 220g), 10 g cashew nut, 50 g white mushroom, 2 g salt, an appropriate amount of white pepper powder, 720 ml water
Milkshake| 1min| 1pc red pitaya (about 400 g), 300 ml yoghurt, 5 ice cubes (2 cm in size), an appropriate amount of honey
Soy milk| 35m in| Soybeans 70 g (about 100 ml mark on the measuring cup), 3 red dates and 10 wolfberries with water added to the 1000 ml mark Note: Only jam, soy milk, smooth soup, and chunky soup are available for scheduling in advance. Other recipes do not support this function.
Manual| 30sec| For example, for Fruit & vegetable juice, 940 g carrot, 660 ml water
Tip: When using joyami Smart Blender for continuously making fruit & vegetable juice, the working time should not exceed 2 min each time, and the total working time should not exceed 6 min. During the operation, if the main base is overheated, stop the operation for about 20 min, and resume it after the main base cools down.

Cautions:
Only Jam, Smooth soup, Chunky soup and Soy milk are available for scheduling in advance. Other recipes do not support this function.
Fault Code

the food in the jar, wait until the device cools down, then power it on and start again
E02| Place the jar| No jar is placed| Exit after placing the jar
Place the lid| No lid is placed| Exit after placing the lid
E05| Overheated| The bottom temperature sensor gives a high-tem- perature alarm| The device will resume the program automatically when the temperaturi drops, and at this moment press th E Cancel button to enter the standby state
E010| Temperature sensor error| The bottom temperature sensor is open-/short- cir- cuited| Fault is not repairable
E011| Communication error| Communication is abnormal between the power supply board and the display board| Fault is not repairable

Troubleshooting

· Add water until it reaches the correct water level line
· Select a mode as instructed herein
· Contact after-sales service
Burning on the bottom| · Add an appropriate amount of ingredients
· Do not add flour or other ingredients building up and causing serious burning on the bottom
· Add water until it reaches the correct water level line
· Wash and clean the jar thoroughly before use
· Select a mode as instructed herein
· Contact after-sales service
Ingredients is not cut fully| · Add an appropriate amount of ingredients
· Add water until it reaches the correct water level line
· Select a mode as instructed herein
· Contact after-sales service
Food is not hot when the program is completed| · Select a mode as instructed herein
· Contact after-sales service
The display screen is not on| · Check whether the power cord is proper and make sure it is plugged and powered on correctly
· Contact after-sales servic
The display screen is on, but the device doesn’t work| · Re-select and confirm a mode, and press the screen to start the device
· Add water until it reaches the correct water level line, wait until the device cools, and then restart the device
· Unplug the power cord, then plug it again and operate the steps as normal
· Contact after-sales service
Work noise| · Blending sound from the motor is a normal phenomenon
· Contact after-sales service

Tip 1: Check whether the power supply is connected properly and whether the jar and lid are installed in place. In case of an abnormal situation such as abnormal noise, smell, and smoke, immediately power off and stop the device.
Tip 2: If the device does not work properly even after the inspections above, please contact after-sales service.

Basic Parameter

After-sale Service
Please visit the official website at https://www.joyami.com ,if you need after-sales service or other information, or encounter any problem.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

User Manual Version: V0.6
Maunfacturer：Chunmi Technology (Shanghai) Co., Ltd.
Address：Building 11, 1333 Jiangnan Avenue, Changxing Science and Technology Park, Lingang,
201203 Shanghai, PEOPLE’S REPUBLIC OF CHINA

References

• joyami

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>