beko HNT61110X Cooker Hood User Manual
- June 6, 2024
- Beko
Table of Contents
beko HNT61110X Cooker Hood
Please read this user manual first!
Dear Valued Customer,
Thank you for preferring this Beko appliance. We hope that you get the best
results from your appliance which has been manufactured with high quality and
state-of-the-art technology. For this reason, please read this entire user
manual and all other accompanying documents carefully before using the
appliance and keep it as a reference for future use. If you handover the
appliance to someone else, give the user manual as well. Follow the
instructions by paying attention to all the information and warnings in the
user manual.
Remember that this user manual may also apply to other models. Differences
between models are explicitly described in the manual.
Meanings of the Symbols
Following symbols are used in various sections of this user manual:
Important safety and environmental instructions
General safety
Important Safety Instructions Read Carefully And Keep For Future Reference
This section contains safety instructions that will help protect from risk of
fire, electric shock, exposure to leak microwave energy, personal injury or
property damage. Failure to follow these instructions shall void any warranty.
-
Beko products comply with the applicable safety standards; therefore, in case of any damage on the appliance or power cable, it should be repaired or replaced by the dealer, service center or a specialist and authorized service alike to avoid any danger. Faulty or unqualified repair work may be dangerous and cause risk to the user.
-
This appliance is intended to be used in household and similar applications such as:
– Staff kitchen areas in shops, offices and other working environments;
– Farm houses
– By clients in hotels, and other residential type environments;
– Bed and Breakfast type environments. -
Operate the appliance for its intended purpose only as described in this manual.
-
The manufacturer cannot be held liable for damages resulting from improper installation or misuse of the product.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Children shall not be allowed play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of your product must be at least 65 cm.
-
If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account.
-
Make sure that your mains power supply complies with the information supplied on the rating plate of the appliance.
-
Never use the appliance if the power cable or the appliance itself is damaged.
-
Prevent damage to the power cable by not squeezing, bending, or rubbing it on sharp edges. Keep the power cable away from hot surfaces and naked flame.
-
Use the appliance with a grounded outlet only.
WARNING: Do not connect the appliance to the mains until the installation is fully complete. -
Place the appliance in a way so that the plug is always accessible.
-
Do not touch the lamps if they have operated for a long time. They can burn your hands since they will be hot.
-
Follow the regulations set out by competent authorities on discharge of the exhaust air (this warning is not applicable for use without flue).
-
Operate your appliance after putting a pot, pan etc. on the hob. Otherwise, high heat may cause deformation in some parts of your product.
-
Turn off the hob before taking the pot, pan etc. from it.
-
Do not leave hot oil on the hob. Pans with hot oil may cause self combustion.
-
Pay attention to your curtains and covers since oil may catch fire while cooking food such as fries.
-
Grease filter must be cleaned at least monthly. Carbon filter must be replaced at least every 3 months.
-
Product shall be cleaned accordance with user manual. If cleaning was not carried out in accordance with user manual, there may be fire risk.
-
Do not use non-fire-resistant filtering materials instead of the current filter.
-
Only use the original parts or parts recommended by the manufacturer.
-
Do not operate the product without the filter and do not remove the filters while the product is running.
-
In the event of be started any flame, de-energize your product and cooking appliances.
-
In the event of be started any flame, cover the flame and never use water to extinguish.
-
Unplug the appliance before each cleaning and when the appliance is not in use.
-
The negative pressure in the environment should not exceed 4 Pa (4×10 bar) while the hood for electric hob and appliances running on another type of energy but electricity operate simultaneously.
-
In the environment where the appliance is being used, the exhaust of devices running on fuel oil or gas, such as room heater must be absolutely isolated or device must be hermetical type.
-
When connecting the flue, use pipes with a diameter of 120 or 150 mm. Pipe connection must be as short as possible and have as few elbows as possible.
-
Danger of choking! Keep all the packaging materials away from children.
CAUTION: Accessible parts may become hot when used with cooking appliances. -
The product outlet must not be connected to air channels that include other smoke.
-
The ventilation in the room may be insufficient when the hood for electric hob is used simultaneously with the devices operating on gas or other fuels (this may not apply to appliances that only discharge the air back into the room).
-
Objects placed on the product may fall. Do not place any objects on the product.
-
Do not flambe under the your product.
WARNING: Before installing the Hood, remove the protective films. -
Never leave high naked flames under the hood when it is in operation
-
Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
Compliance with the WEEE Directive and Disposing of the Waste Product:
This product complies with EU WEEE Directive (2012/19/EU). This product bears
a classification symbol for waste electrical and electronic equipment (WEEE).
This symbol indicates that this product shall not be disposed with other
household wastes at the end of its service life. Used device must be returned
to official collection point for recycling of electrical and electronic
devices. To find these collection systems please contact to your local
authorities or retailer where the product was puchased. Each household
performs important role in recovering and recycling of old appliance.
Appropriate disposal of used appliance helps prevent potential negative
consequences for the environment and human health.
Compliance with RoHS Directive
The product you have purchased complies with EU RoHS Directive (2011/65/EU).
It does not contain harmful and prohibited materials specified in the
Directive.
Package Information
Packaging materials of the product are manufactured from recyclable
materials in accordance with our National Environment Regulations. Do not
dispose of the packaging materials together with the domestic or other wastes.
Take them to the packaging material collection points designated by the local
authorities.
General appearance
Overview
- Slinder panel
- Control panel
- Grease filter
- Lighting
Technical data
Model | HNT61110X |
---|---|
Supply Voltage and Frequency | 220-240V ~ 50 Hz |
Lamp Power | 2 x 3 W |
Motor Power | 125 W |
Flow rate – 3. Level | 253 m³/h |
Insulation Class of Motor | Class F |
Insulation Class | Class I |
Using the appliance
Controlling the appliance
KEY | FUNCTION |
---|---|
A : Light On / Off | Pull the sliding plate to the |
front. Press the button downwards to turn on the lamp or upwards to turn off
the lamp.
B : 1 and 2 Speed Button| Pull the sliding plate
to the front. Press the button upwards to op- erate the hood at speed level 1,
and downwards to operate the hood at speed level 2.
C : 3rd Speed Button| Pull the sliding plate to the front. Press the
button downwards to operate the hood at speed level 3.
Energy efficient usage
- When using your appliance, adjust the speed settings according to vapour and odour intensity, in order to save energy.
- Use low speeds (1-2) under normal conditions, and high speed (3) for intense odour and vapour.
- The lamps on the hood are placed for illuminating the cooking area.
- Using them for environmental lighting shall cause unnecessary energy expenditure and insufficient lighting.
Operating the hood
- Your appliance contains a motor that has various speeds.
- For better performance, we recommend using low speeds under normal conditions and high speeds in cases of strong odours and intense vapour.
- You can start your appliance by pressing on the desired speed setting button. (B, C)
- You may illuminate the cooking area by pressing the lamp (A).
Replacement of lamp
CAUTION: Disconnect the electrical supply of the hood. Leave the lamps
to cool down first because they co-uld burn your hands when they are hot.
Remove the aluminium cartridge filter. Remove the defective bulb and replace with a new one with the same rating.
Bulb|
---|---
Bulb Power| 3 W
Holder / Socket| E 14
Bulb Voltage| 220 – 240 V
Size| 35 x 100 mm
ILCOS Code| DRBB/F-3-220- 240-E14-35/100
Luminous flux| 400 lm
Correlated colour tem- perature| 2700 K
This product contains a light source of energy ef-ficiency class “E”.
Operation with chimney connection
- Vapour is extracted through the flue duct, which is fastened to the connection head on the hood.
- The diameter of the flue duct must be the same as the connection ring. In horizontal settings, the pipe has to have a slight upward slope (around 10º) so that the air can exit the room easily.
Operation without chimney connection
- Air is filtered through the carbon filter and recirculated in the room. Carbon filter is used when it is impossible to use a flue in the house.
- In flueless use, remove the flaps inside the flue adapter.
- Remove the aluminum grease filter. To install the carbon filter, fit the filter to the tabs by centring it on the plastic piece on both sides of the fan body. tighten it by turning right or left.
- Replace aluminum grease filter.
Cleaning and Maintenance
Before cleaning and maintenance, unplug the product or turn off the switch.
Cleaning of grease filter
Grease filter is used to retain the oil particles in the air. Grease filter
may change colour after repeated cleaning. This is normal, and you do not have
to replace your filters.
- External grease filter
- Internal grease filter
- Pull the sliding plate out by holding the front panel. Remove the external grease filter first, and then the internal grease filter.
- Push the grease filter lock forward.
- Then pull it slightly down and pull it out. Otherwise, you may bend the filter. Wash and rinse grease filter with liquid detergent and replace grease filter to their seats by carrying out the steps specified above in reverse order. These grease filter are used to retain the oil particles in the air.
You may also wash the grease filter in the dishwasher.
CAUTION: In case of normal use, clean your grease filter once in a month.
Replacement of carbon filters
Odour removing filters contain charcoal (Active carbon). Grease filter must be
installed in the product, regardless of whether or not carbon filters are
used.
- Remove the grease filter.
- To remove the carbon filter, remove the carbon filter from its housing by rotating it counter-clockwise from the tab.
- Install the new carbon filter.
- Install the grease filter.
CAUTION
- Carbon filter shall never be washed.
- Replace carbon filters once every 3 months.
- You can obtain the carbon filter from the authorized services.
Installation of appliance
WARNING: Before starting the installation, read the safety information on
user manual.
WARNING: Failure to install with screws and stabilizers in accordance
with these instructions may result in electric shock.
For the installation of the hood, please contact the nearest Authorized
Service.
It is the customer’s responsibility to prepare the location and electrical
installation of the hood.
Position of the appliance
- Distance between the cooker and the cooker hood must be considered prior to assembly. This distance should be 65 cm.
- Distance must be measured from the surface of grate for gas cookers,
- from surface of glass for electric cookers.
Installation accessories
- Hood
- 4x 4 x 40 Screws
- User manual
- Mounting Template
- Ø120mm Plastic Flue Flap
The information required to make the location suitable for the installation of the hood is given below.
installation of the Hood
CAUTION: Use protective gloves and goggles for drilling and cutting
operations.
- Paste the installing template provided with the hood on the surface where the hood is to be mounted.
- Make holes with Ø4 mm diameter on the points marked as A, B, C, D on the installation template.
- Drill the flue outlet hole specified in the installing template in the sizes given.
Remove the appliance from its packaging. Install the plastic flue flaps provided in the accessories to the air outlet flue of the appliance as shown below.
- Flap Pin Socket
- Flap Pin
Insert the plastic pin (Figure 1/area no. 2) on the pin socket on the motor exhaust (Figure 1/area no.1). Then bend the flap lightly to insert the other pin on the flap and insert the other pin to its socket (Figure 1).
By using the 4 x 40 screws provided with the hood, install the appliance to the cabinet from the points A, B, C and D. When the slider set moves, the front panel shall not rub on the cabinet door (Figure 2)
Install flexible aluminium pipe to plastic flue outlet. Install the other end of the pipe to the flue hole on the wall (Figure 3).
Connecting to flue
If you are going to use the Ø 120/150 mm plastic flue adapter, connect one end
of the pipe to this adapter, if you are not going to use it, to the direct
output on the product. Connect the other end of the pipe to your flue. Check
that these two connections are tight enough so they will not come out when the
appliance runs on full power. Ensure that the flaps inside the flue work when
tightened with clamp. Connect the flue connection duct outside the adapter. If
the connection duct is fitted inside the adapter, the covers that prevent air
return shall remain closed and air won’t be sucked in. The length of the pipe
connection, as well as the number of elbows, must be as minimum as possible.
A: Flue exit pipe
B: Non return flaps
C: Plastic Flue
The valves are closed then the appliance is not operating and prevent possible outside odour and dust from entering inside.
Storage
- If you do not intend to use the appliance for a long time, please store it carefully.
- Please make sure that the appliance is unplugged, cooled down and totally dry.
- Store the appliance in a cool and dry place.
- Keep the appliance out of the reach of children
Handling and transportation
- During handling and transportation, carry the appliance in its original packaging. The packaging of the appliance protects it against physical damages.
- Do not place heavy loads on the appliance or the packaging. The appliance may be damaged.
- Dropping the appliance will render it non-opera-tional or cause permanent damage.
Troubleshooting
Troubleshooting | Root cause | Help |
---|---|---|
Appliance is not working. | Check your fuses. | Fuse may be blown, inspect and |
restore it.
Appliance is not working.| Check the electrical connection.| Mains voltage
shall be between 220 and 240 V.
Appliance is not working.| Check the electrical connection.| Check if other
appliance in your kitchen operate.
Illumination light does not operate.| Check the electrical connection.| Mains
voltage shall be between 220 and 240 V.
Illumination light does not operate.| Inspect the lamp switch.| Lamp switch
shall be at “on” position.
Illumination light does not operate.| Inspect the lamps.| The lamps of the
appliance shall illuminate.
Air inlet of the appliance is inadequate.| Inspect the grease filter.| Under
normal operating conditions, grease filter shall be cleaned at least once in a
month.
Air inlet of the appliance is inadequate.| Check the air discharge chimney.|
The air discharge chimney shall be at “on” position.
Air inlet of the appliance is inadequate.| Inspect the carbon filter.| The
filters of the appliances with carbon filters shall be replaced once in every
3 months under normal conditions.
References
- Arctic Romania - Electrocasnice pentru intreaga familie
- Beko Global
- Beko Romania - Electrocasnice cu Tehnologii Ingenioase
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>