RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan Owner’s Manual
- June 6, 2024
- RYOBI
Table of Contents
The RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan Owner’s Manual provides important safety instructions, assembly guidelines, and operational information for the RYOBI PMF01 18 Volt Bucket Top Misting Fan. This product is designed to provide outdoor cooling while connected to a 5-gallon bucket or a garden hose, as well as fan-only mode. The manual includes detailed instructions on how to adjust the misting angle, install and remove the battery pack, and use the misting fan with a water bucket or garden hose. It also provides important safety instructions on how to avoid electric shock, fire, and serious personal injury. The manual emphasizes the importance of reading and understanding all instructions before using the product to reduce the risk of injury. The RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan Owner’s Manual is an essential guide for anyone who wants to use this product safely and effectively.
OPERATOR’S MANUAL
18 VOLT BUCKET TOP MISTING FAN
PMFO1
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.
- Children can fall into buckets and drown. Keep children away from buckets with even a small amount of liquid.
- To reduce the risk of injury, close supervision is necessary when a product is used near children.
- Do not allow children to operate this product. It is not a toy.
- Exercise caution to avoid slipping or falling.
- Use only recommended accessories. The use of improper accessories may cause risk of injury.
- Never leave product running unattended. Turn hose faucet completely off and remove battery pack. Don’t leave product until spray comes to a complete stop.
- Never direct mist or water toward any electrical wiring or devices.
- Ensure that all hoses and accessories are properly connected before using the product.
- ONLY use clean, cold water.
- For outdoor use ONLY.
- Do not use this misting fan to spray pesticides, liquid fertilizers, chemicals, or any liquids other than clean water. Spraying these substances could result in serious injury or illness to the operator or bystanders.
- Make sure hose and mist tube are located so that they will not be stepped on, tripped over, come in contact with sharp edges or moving parts, or otherwise subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury and damage to the hose and mist tube which could prevent the product from working properly.
- Use caution when positioning the product for use. Never place the unit near electrical outlets or switches.
- Check hoses and parts for signs of damage. Replace any damaged hoses or parts.
- Verify that all connections are secure before operating the unit.
- Use caution when using in windy conditions. Winds may carry mists into electrical wiring or devices.
- Do not kink or overbend the hose or mist tube.
- Be careful not to spill water when filling a water bucket. Ensure all hose connections are secure before using misting fan. Spilled water and leaks can result in a slippery surface and create a slip and fall hazard.
BATTERY PRODUCT USE AND CARE
- Use battery-operated products only with specifically designated battery pack. Use of any other batteries may create a risk of fire.
- Use battery only with charger listed. For use with 18V lithium-ion battery packs, see tool/appliance/battery pack/charger correlation supplement 987000-432.
- Dress properly. Do not wear loose clothing or jewelry, Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
- Avoid accidental starting. Be sure switch is in the off position before inserting battery pack. Carrying battery products with your finger on the switch or inserting the battery pack into a product with the switch on invites accidents.
- Do not use battery product if switch does not turn it on or off. A battery product that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect battery pack from product before making any adjustments, changing accessories, or storing the product. Such preventive safety measures reduce the risk of starting the product accidentally.
- When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or fire.
- Keep the product dry, clean, and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your battery product. Following this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.
- Know your product. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this battery product. Following this rule will reduce the risk of electric shock, fire, or serious injury.
- Battery products do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery product or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
- Do not place battery products or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury.
ASSEMBLY
WARNING:
Do not use this product if it is not completely assembled or if any parts
appear to be missing or damaged. Use of a product that is not properly and
completely assembled or with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create accessories or attachments
not recommended for use with this product. Any such alteration or modification
is misuse and could result in a hazardous condition leading – to possible
serious personal injury.
If any parts are damaged or missing, please call 1-800-525-2579 for assistance.
OPERATION
WARNING:
Do not allow familiarity with products to make you careless. Remember that
a careless fraction of a second is sufficient to inflict serious injury.
WARNING:
Keep water and mist discharge pointed away from all electrical devices to
reduce the risk of electrocution or electric shock.
WARNING:
Ensure all hose connections are secure before using misting fan. Spilled water
and leaks can result in a | slippery surface and create a slip and fall
hazard.
WARNING
Do not use any attachments or accessories not recommended by the
manufacturer of this product. The use of attachments or accessories not
recommended can result in serious personal injury.
WARNING:
Always remove battery pack from the product when you are assembling parts,
making adjustments, cleaning, or when not in use. Removing battery pack will
prevent accidental starting that could cause serious personal injury.
WARNING
Do not use this product to spray pesticides, liquid fertilizers, chemicals, or
any liquids other than clean water. Spraying these substances could result in
serious injury or illness to the operator or bystanders.
APPLICATIONS
You may use this product for the following purposes:
- Outdoor cooling while connected to a 5-gallon bucket or a garden hose
- Fan only
FAN LOW/OFF/HIGH SWITCH
See Figure 1, page 9.
The LOW/OFF/HIGH fan switch is located on the left front of the base.
- To select LOW speed, press (1).
- To select HIGH speed, press (Il).
- To turn the fan OFF, select the center position (O ).
PUMP LOW/OFF/HIGH SWITCH
See Figure 1, page 9.
The LOW/OFF/HIGH pump switch is located on the right front of the base.
- To select LOW speed, press (1).
- To select HIGH speed, press (II).
- To turn the pump OFF, select the center position (0 ).
INSTALLING/REMOVING THE BATTERY PACK
See Figure 2, page 9.
NOTE: This product is not recommended for use with RYOBI ONE+ battery packs
larger than 4.0Ah. If installed, large capacity battery packs will prevent the
battery cover from closing completely exposing the battery and the battery
port to moisture, debris, and other contaminants.
- Set both switches to the OFF (QO) position.
- Press the tab to open the battery compartment latch.
- Insert the battery pack into the battery port.
- Make sure the latches on each side of the battery pack snap into place and the battery pack is secured before beginning operation.
- Close the battery compartment cover and press until it snaps shut.
ADJUSTING THE MISTING ANGLE
See Figure 3, page 9.
The fan can be angled forward -15° or back 45° to adjust the direction of the
mist.
USING THE MISTING FAN WITH A WATER BUCKET (NOT INCLUDED)
See Figures 4 – 5, pages 9 – 10.
WARNING:
Children can fall into buckets and drown. Keep children away from buckets with
even a small amount of liquid.
The misting fan is designed to operate atop a 5-gallon water bucket.
NOTE: Clean the bucket with soap and water before each use.
-
Place the bucket on a flat, level surface.
-
Set the fan switch and pump switch to the OFF (QO) position.
-
Set the fan’s base securely onto the rim of the bucket.
NOTE: The fan cannot be attached to the bucket; they cannot be moved as a single unit. -
The end of the intake tube should go straight down into the bucket.
-
Install the battery pack and close the battery compartment cover.
-
Add ONLY clean, cold water into the bucket. Do not overfill.
-
Press the pump switch to LOW (1) or HIGH (II).
-
Press the fan switch to LOW (1) or HIGH (II).
WARNING:
When filling, moving, or emptying bucket, be careful not to spill water and do not overfill bucket. Spilled water can result in a slippery surface, create a slip and fall hazard, and cause property damage. away from buckets with even a small amount of liquid.
To move the fan to another location:
- Set the fan switch and pump switch to the OFF (0) position.
- Allow the the fan and pump to stop running before lifting the fan off the bucket.
- The intake tube may be stored in the space provided on the unit.
NOTE: The intake tube cannot be removed.
USING THE MISTING FAN WITH A GARDEN HOSE (NOT INCLUDED)
See Figure 6, page 10.
WARNING:
Always route hoses away from traffic areas to prevent a tripping hazard.
- Choose a flat, steady surface, such as a concrete patio or tabletop.
- Set the fan switch to the OFF (QO) position.
- With the water faucet turned completely off, attach a garden hose (not provided) securely to the intake tube coupler and hand tighten.
- Install the battery pack and close the battery compartment.
- Turn the garden hose faucet on all the way and allow the hose to fill with water.
- Press the fan switch to LOW (1) or HIGH (II) position.
USING THE FAN WITHOUT MIST
lf desired, this product may be used as a fan only, when not connected to a
water source. Always disconnect the garden hose and place the misting tube in
its storage area.
NOTE: The pump is not needed when the fan is connected to a garden hose.
Using the pump unnecessarily may cause additional wear and shorten the life of
the unit.
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts. Use of any other parts
could create a hazard or cause product damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are
susceptible to damage from various types of commercial solvents and may be
damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-based products,
penetrating oils, etc., come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which could result in serious personal
injury.
WARNING:
With the battery pack removed from the misting fan, always clean and
thoroughly dry out all parts of the misting fan, intake tube, and buckets when
not in use to prevent the possible formation of bacteria or mold. Spraying
mist that contains bacterial or mold can result
in serious personal injury or illness.
NOZZLE MAINTENANCE
See Figure 7, page 10.
WARNING:
Ensure all nozzle maintenance is properly performed to prevent leaks. Leaks
can result in a slippery surface, create a slip and fall hazard, or cause
property damage. Irregular mist patterns or leakage may be the result of a
clogged or dirty nozzle.
To clean nozzles:
- Make sure both the power switch and pump switch are in the OFF (QO) position.
- Remove the battery pack.
- Remove the brass nozzles from each side of the fan.
- Soak nozzles in nozzle cleaner (not included) to loosen foreign materials clogging or restricting the nozzle.
- Using a garden hose, flush debris out of nozzle by backflushing (running the water through the nozzle backward or from the outside to the inside).
- Reconnect the nozzles.
FILTER MAINTENANCE
See Figure 8, page 10.
Periodically check the filter at the end of the intake tube for debris and to
make sure it is in good condition. Remove the plastic filter cover and rinse
or replace the filter, then snap the cover back together.
ACCESSORIES
To order these accessories, call 1-800-525-2579.
- Brass NOZZ10…………………………………………………………………………………………………………………Model No. PMC080
- Inline Misting Filter…………………………………………………………………………………………………………..Model No. PMC080
- Nozzle Cleaner ………………………………………………………………………………………………………………..Model No. PMCCO008
WARNING:
Current attachments and accessories available for use with this product are
listed above. Do not use any attachments or accessories not recommended by the
manufacturer of this product. The use of attachments or accessories not
recommended can result in serious personal injury.
TROUBLESHOOTING
PROBLEM | POSSIBLE CAUSE | SOLUTION |
---|---|---|
Leak at nozzle or threaded hole | Nozzles were installed improperly. Nozzles | |
clogged or dirty. | Reinstall nozzles and tighten securely. Clean nozzles. | |
Fan will not start | Battery is defective or fully discharged. | Charge battery |
or contact customer service.
NOTE: ILLUSTRATIONS START ON PAGE 8 AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.
Fig. 1
FAN LOW/OFF/HIGH SWITCH
A -LOW speed
B – OFF
C -HIGH speed
PUMP LOW/OFF/HIGH SWITCH
D -LOW speed
E- OFF
F-HIGH speed
Fig. 2
A- Compartment latch
B-Battery port
C-Battery pack
D- Latches
E – Battery compartment
F -Battery compartment cover
Fig. 3
ADJUST FROM -15° TO 45°
Fig. 4
PLACE FAN ON TOP OF 5-GALLON BUCKET
A-5-Gallon bucket [Seau de 18,93
B- Intake tube
Fig. 5
Fig. 6
A – Garden hose connector
B – Garden hose
Fig. 7
A – Brass nozzles
Fig. 8
A – Filter cover
B – Filter
SPECIFICATION
Product Name
|
RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan
---|---
Model Number
|
PMF01
Power Source
|
18V lithium-ion battery pack
Applications
|
Outdoor cooling while connected to a 5-gallon bucket or a garden hose, fan only
Fan Speeds
|
Low/Off/High
Pump Speeds
|
Low/Off/High
Adjustable Misting Angle
|
Forward -15° or back 45°
Recommended Water Source
|
Clean, cold water
Recommended Water Bucket Size
|
5-gallon bucket
Recommended Battery Pack
|
18V lithium-ion battery pack
FAQS
Can I use the RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan with a
water bucket?
Yes, you can use the RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan with a 5-gallon water bucket. However, you should ensure that the bucket is clean and placed on a flat, level surface before using it with the misting fan.
How do I adjust the misting angle of the RYOBI Fan Mister: PMF01 18V Bucket
Top Misting Fan?
To adjust the misting angle of the RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan, you can angle the fan forward -15° or back 45° to adjust the direction of the mist.
Can I use the RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan to spray
pesticides or chemicals?
No, you should not use the RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan to spray pesticides, liquid fertilizers, chemicals, or any liquids other than clean water. Spraying these substances could result in serious injury or illness to the operator or bystanders.
What are some important safety instructions to follow when using the RYOBI
Fan Mister: PMF01 18V Bucket Top Misting Fan?
Some important safety instructions to follow when using the RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan include keeping children away from buckets with even a small amount of liquid, using only recommended accessories, never leaving the product running unattended, and ensuring that all hoses and accessories are properly connected before using the product.
What is the RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan designed
for?
The RYOBI Fan Mister: PMF01 18V Bucket Top Misting Fan is designed to provide outdoor cooling while connected to a 5-gallon bucket or a garden hose, as well as fan-only mode.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>