RollMaster MARK1000 4K Wireless Video Transmission System User Manual
- June 6, 2024
- RollMaster
Table of Contents
RollMaster MARK1000 4K Wireless Video Transmission System
Product Features
-
[Wireless/wire double-purpose video transmitter/ receiver]
-
[Big colorful screen. Easy to read. When the transmitter is far from people, the screen still can be seen.]
-
[With fan cooling system, the performance is more steady.]
-
[Various power options(low power warning)]
-
[KM Grade video transmitter/ receiver]
The transmission distance can be as far as 1km when the transmitter matches ProFocus Directional antenna -
[300m/ 1000ft meters transmission distance.]
With Standard antennas,the signal can travel up to 300m/1000ft Sight in the real test. -
[ Real-time transmission with steady signal.]
Dual CPU, Dual system.Video processing and signal transmission operate independently. -
[channal]
Transmitter and receiver can be used normally when they are on the same channel. 15 channels can be chosen and be switched manually to avoid interference. -
[signal symbol on screen]
Signal symbol can display the strength of signal. -
(video format supported)
Mark-1000(4K) :4K(3840*2160)30fps 1080P/I 720P/ 60HZ. -
[Widely Match different photography accessories.]
Batteries need to be purchased separately.
The interface is designed with universal 1/4 threaded hole which can connect with magic arm, tripod, camera hot shoe adaptor and other accessories etc. It ensures simple and quick set-up for your units. -
[Various power options]
Three different powering ways(DC7-16V, V mount Battery, FSS0 series battery) meets your requirements in different conditions and occasions. -
[withstand wear and tear]
CNC oxidation treatment and Aluminum Alloy material enable the device solid as well as durable. Glossy processing on edge make it looks beautiful and exquisite. -
[compact and flexible]
The set only weighs24lg/pcs.lt is portable and practical. -
[OSD display and firmware upgrade]
HDMI loop out port on transmitter and output video of receiver support OSD display. Firmware upgrade is available. -
[Protection base]
Special protection base for antenna port to avoid bumps. -
[HDMI loop out port]
HDMI loop out port provides convenient real-time monitoring on transmission end. -
[AES128 bit encryption Transmission.]
Transmission is encrypted to guarantee more safety and reliable protection. -
[long-lasting operation hours.]
Internal high performance and low power consuming chip extends operation hours and solves the problem of frequent charging after long time use. -
[Supportive app scan system]
Open app to check surrounding idle channel and occupied channel information.The information is corr-esponding to the channel on 7 segment LED display of the video transmitter.
Packing list
Please check the package inside to assure it contains the parts as below.
If any part missed, please contact the distributor or supplier.
- Transmitter body * 1
- Receiver body * l
- Antenna * 4
- HDMI wire * 2
- Hot shoe adaptor * 2
Product Introduction
- Antenna protection base
- colorful digital screen
- Ethernet interface
- cooling fan
- IN DC
- battery safety lock button
- battery amount
- transmitter slgnal input
- transmltter signal loop out
- usb upgrade port
- video indicator
- vent
- threaded hole
- receiver signal output
- channel selection button
- set button
- fan button
- on/ off button
- mode
- power mode
- signal strength display
- fan symbol
- voltage
- transmitter/ receiver antenna
- transmitter/ receiver body
Installation steps
Warning & Attention
Step 1: Connect4 antennas with the antenna pedestal on the top of the
main body before operating. (2 antennas fortransmitter,2 antennas for
receiver).
The antenna should stand vertical upwards(As the picture shows below).
HDMI in port of the transmitter connect the video source device(camera or
camcorder.
HDMI out port of the receiver connect the monitor.
The
antenna should stand vertical upwards
Signal is best when panels of Transmitter and Receiver are parallel to each other.
Display and button functions
K1.on/off
K2.fan cooling button
K4.set button
K5.Channel button
-
mode display
-
power mode display
-
signal strength display
-
fan symbol
-
voltage display
-
image quality mode
-
on/off button Kl
Press Kl button for 2 seconds to start and operate the same way to shut down.
Press Kl button twice to switch the mode (A B C).
Mode A: wireless mode.
Mode B: wire mode.
Transmitter and receiver can be used as extender when they are connected with one pcs Ethernet cable.
Mode C: wireless Ethernet interface data transmission. -
fan on/off button K2
Press K 2 button for 2 seconds, the fan symbol on screen will rotate.
Press K2 button for 2 seconds, the fan symbol on screen will stop rotating.
Press K2 button twice to switch LCD open mode and LCD close mode. -
Press Kl and K2 at the same time to switch power input way (The lower power warning will be different when input way is different)
Way LDC input
Way 2. NP FSS0, F750 battery input
Way 3. V mount battery input -
set button K4
A. Press K4 button for 3 seconds to start OSD display, Press K4 button
for 3 seconds to close OSD display function
B. Image quality mode:
1.standard mode
2.Distance priority mode
3.image quality strengthened mode
▲ Press K 4 button twice to switch mode 1 and mode 2
It is standard mode when VIOD symbol on screen is on while it is distance priority mode when VIOD symbol is off.
Press K 4 button for three times to switch mode 1 and mode 3
▲ It is standard mode when VIOD symbol on screen is on while it is image quality strengthened mode when VIOD symbol flash once per second. -
Channel selection- K 5 button Press KS button once to switch channel. The device can be normally used when transmitter and receiver are on the same channel.
Technical Parameters
Item No.
| Mark-1000(4k)
---|---
Net Weight|
24lg/ pcs do not include battery and wire
Dimension
|
1007533 mm (include built-in Battery Plate, do not include battery)
material
|
Aluminum alloy
Battery Plate
|
Compatible with Sony Series Battery, such as F550 F750 F970 etc.
External V-mount battery plate is available.
(can be purchased separately)
Working hours
|
F550 for about 2 hours
F750 for about 4 hours
F970 for about 6 hours
Current
| 8V 700MA/600MA
power supply|
7-16V DC F series battery V Mount Battery
Video format
|
Mark-1000(4k)
|
4k(3840*2160)30fps
1080P/1 720P/60HZ
Frequency
|
5.18-5.24GHZ
Interface
|
Transmitter: HDMI input/loop out
Receiver: HDMI output, antenna port*2 DC 7V-16V power port, FSSO Battery
series power port
HDMI standard
| HDMI .4
Ethernet Interface|
RJ45
Channel
| 15 5G channels
transmission distance|
1000ft/300M + (Light of Sight)
Environment temperature
| 0°C -45°C (32°F – 113°F)
Transmitter/ receiver Highest working temperature|
50°C (l22°F) transmitter/40°C (l04°F) receiver
Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’ s authority to operate the
equipment.
Warning:
After you set up the device, in order to better experience, please keep a
distance of at least 20cm of use
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
televi~ion reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
RF exposure compliance statement
This device has been evaluated to meet the general RF exposure requirement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.