baseaire O-UVC2 Pro Ozone Generator User Manual
- June 6, 2024
- BaseAire
Table of Contents
- O-UVC2 Pro Ozone Generator
- Device Description
- Structure
- Operation
- State Description of Switch
- Overall Workflow
- Mistakes and Shortcomings
- Maintenance
- Cleaning
- Clean Electrode
- Transportation and Storage
- Transportation
- Storage
- Technical Annex
- Electrical Wiring Diagram
- Limited Warranty
- Warranty Period
- BaseAire Warranty Steps:
- Limited Warranty Exclusions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
O-UVC2 Pro Ozone Generator
Installation & Operations Manual
Tel: 1-888-641-8862
Web: www.baseaire.com
E-mail: sales@baseaire.com
Device Description
The O-UVC2 Pro Ozone Generator of the Baseaire series uses oxygen in the surrounding air as a molecular compound.
The ozone generator sucks in the surrounding air and performs a discharge procedure. After that, energy breaks the diatomic oxygen molecule into two single oxygen atoms in the form of free radicals.
Atomic oxygen recombines with oxygen molecules (A) to form ozone.
Ozone is a very powerful oxidant with high reaction potential. This makes it an effective agent for decomposing destructive substances in the surrounding air. The free radicals bound in the ozone molecule are separated from the molecular compound (B) and react with all substances in the surrounding air, even if these substances are only present in a small concentration. The oxidative decomposition of pollutants in the air and immovable pollutants (for example, on the floor, wall or ceiling) will eliminate and eliminate odors by killing viruses, bacteria, molds, and carcinogenic/allergenic microorganisms.
After the reactant oxidizes the oxygen atoms, the ozone molecules will be converted into oxygen molecules.
Due to their metastable bonds, unoxidized ozone molecules will also decompose into oxygen after a period of time without leaving harmful residues. In indoor spaces and under normal conditions, the half life of ozone is approximately. 30 to 60 minutes. This means that the ozone concentration in indoor air is naturally reduced by at least half every hour.
Structure
- Upper shell
- Plastic handle
- Knob
- Gasket
- Fan
- Bottom shell
- Circuit board
- Circuit board
- Generator protective shell
Operation
State Description of Switch
-
The default shutdown state is OFF, power on state is ON, the indicator remains on,
indicating that the ozone generator , fan are always running. -
Rotate the arrow of the knob to the corresponding position, set the operating time with in the range of 00:00 to 02:00, during the operation, the indicator light will turn on, the ozone generator and the fan will keep running, and the arrow of the knob will return to OFF to shut down.
Generally, ozone will automatically decompose into oxygen in about an hour. If a person stays indoors for a long time, it is generally subject to not being able to smell the strong ozone smell.
Overall Workflow
When performing odor neutralization and cleaning cycles, follow the steps below:
- Place the O-UVC2 Pro Ozone Generator in the center of the room.
- Make sure that the equipment and connecting cables are not damaged
- Connect the power cable and connect the device to the power source. Observe the technical parameters.
- Set the timer to the required run time.
- Then turn on the device. The display panel will light up. The cleaning cycle will begin immediately.
Once the preset time has passed, the O-UVC2 Pro Ozone Generator will automatically shut down.
Warning
A The risk of ozone causing harm to the human body!
During use, if you smell ozone outside the working area, the machine must stop
working immediately. Ventilate the room thoroughly.
The following values are used as a general reference for determining the processing time:
Mistakes and Shortcomings
The equipment has been checked for normal function several times during the production process. If the fault still occurs, please check the equipment according to the following list.
Warning
A Electric shock is life threatening!
Before performing any operation on the device, please unplug the power plug
from the socket. Do not bypass any electrical safety devices!
In order to ensure the normal operation and trouble-free operation of the equipment, it must be cleaned and maintained regularly.
Maintenance
Electric shock is life-threatening!
Before performing any operation on the device, please unplug the power plug
from the
socket. Do not bypass any electrical safety devices!
Inhalation of ozone can cause injury!
After the equipment stops running, please wait for a while to ensure that the
ozone
concentration is lower than the specified value, and then perform maintenance
and
cleaning
Please perform regular maintenance and maintenance to ensure the normal
operation
and trouble-free operation of the equipment.
The type and frequency of maintenance tasks basically depend on the operating
environment and the time and type of use.
During use, dust and moisture will accumulate inside or inside the component,
which
may affect its function and efficiency.
In a dusty room or after repairing a fire (high humidity level), inspection
and
maintenance should be carried out immediately.
The basic principles for determining equipment operation and maintenance intervals:
- Often
- Per hour
- 1-2 times a week
- In an overly dirty environment
- In a humid room
Regardless of the operating conditions described, you should perform
maintenance if one or
more of the following signs appear:
- The noise level increases when the fan is running,
- Severely polluted soft magnetic stickers.
- Dirty electrodes (identifiable by hissing sound).
The substances produced during the ozone production process gradually disappear.
House Cleaning
Clean the case with a soft, damp, lint-free cloth. Make sure that no moisture
enters the enclosure,
Prevent electrical components from getting wel. Do not use any harsh cleaning
agents, such as cleaning sprays, solvents, alcohol-based cleaning agents, or
abrasives to soak the cloth,
Cleaning
Within the framework of regular maintenance work, it is not only necessary to check the normal condition of the equipment and its accessories, but also to thoroughly clean the equipment and its components.
Proceed As Follows:
Clean the fan
1. Remove the screws on the dust cover.
2. Remove the shell.
3. Disassemble and clean the fan. Always check whether the fan is working properly. If it is only slightly contaminated, you can use a vacuum cleaner or a tap to clean it. If the contamination is serious, clean the reaction generator with a soap solution. After cleaning, insert the fan only after it is completely dry!
Clean Electrode
The electrode can be cleaned in the built-in state. Before cleaning the electrode, check for cracks. Do not use damaged parts!
Use a dry (lint-free) or damp cloth to clean the components. After cleaning, make sure that no fibers (fluff) remain on the electrode.
Do not use the device before the electrodes are completely dry.
The following requirements must be met when installing the Baseaire O-UVC2 Pro
Ozone Generator:
Only use the Baseaire O-UVC2 Pro Ozone Generator according to the parameters provided in the “Technical Data” chapter.
Make sure that there are no obstructions at the air inlet and outlet.
If possible, place the device in the center of the room to ensure optimal air
circulation.
Do not install this machine near flammable substances or gases.
Make sure to place the device on a dry and vibration-free surface.
Ensure that the equipment is protected from splash water.
Transportation and Storage
If you store or transport the device incorrectly, the device may be damaged.
Pay attention to information about transportation and storage.
Transportation
Before transporting the equipment, please observe the following regulations:
- Turn off the device.
- Hold the power plug while unplugging the power cord from the power outlet.
- If the device was in use before, please wait until the timing period is over before transferring the device.
- Do not drag the device with the power cord during transportation to prevent the device from moving and vibrating to avoid damage to the electrode.
After transporting the equipment, please observe the following regulations:
- Install the equipment in an upright position after transportation.
Storage
When the device is not in use, please observe the following storage conditions:
- Store the Baseaire O-UVC2 Pro Ozone Generator in a dry place to avoid the influence of bad weather, and cover it to protect it from invasive dust.
- When the equipment is not in use, always disconnect the power supply.
Technical Annex
Electrical Wiring Diagram
Limited Warranty
All warranty benefits apply to the original owner only. Warranty cannot be transferred or assigned.
Warranty Period
Warranty becomes effective since the date of original purchase and will last for two (2) years.
Who’s Covered?
This limited warranty is only effective for the original purchaser. It is NOT
transferable.
Who’s Not Covered?
This limited warranty is only effective for the original purchaser. It is NOT
transferable.
- Damage caused by the owner when attempting to fix or alter the product by himself or herself.
- Damage caused by misuse, abuse, neglect, alterations or unauthorized repair.
- Natural depreciation
How to Request Warranty Services?
To obtain the benefit of this warranty, please leave your message online (www.baseaire.com), or send an email to sales@baseaire,com
Our customer service will address your issue in 24 hours.
BaseAire Warranty Steps:
1, Once receive the goods, customers must log in www.baseaire.com to fill out
the warranty Registration form and submit to BaseAire company. We will receive
your purchasing and installation information and
save it
If no warranty registration is sent to us, warranty period will begin the day the shipment left the warehouse. Please be sure to record serial # and date of installation. You will need this information to receive the RAnumber.
2. If warranty service is necessary, customers must contact BaseAire Tech
Support by sales@baseaire.com
or local technical service phone to receive a Return Authorization (RA
number). Once an RAhas been issued, customers should bring the unit to a
certified repair center. BaseAire will arrange the shipping to bring the unit
back to the BaseAire warehouse (at the expense of the customers) if customers
are not available.
3. After the unit has been received by BaseAire (whether al a repair center or the warehouse), BaseAire will have an initial inspection If it is determined to be invalid warranty claim (see exclusions below), customers have to pay for all associated repair costs and shipping costs for units repair.
4, Customers can pick up the unit after repair at their own expense for shipping. Units will have a rigorous, testing before sending it back to customers.
5, Ifthe unit can no longer be fixed, and it is in the warranty period and determined to be valid claim, we will ship the customer a new unit within the same year warranty from the date of replacement.
6. After parts are repaired or replaced by BaseAire, the original warranty period continues to applies until meet its deadline. No extensions to the original warranty period
Limited Warranty Exclusions
EXCLUSIONS:
DAMAGE DUE TO THE FOLLOWING IS NOT COVERED UNDER WARRANTY
1. ACTS OF NATURE- INCLUDING BUT NOT LIMITED TO:
Flooding
Fire
Water Damage
Hurricane Storm Damage
2. IMPROPER USAGE-INCLUDING BUT NOT LIMITED TO:
- Pool/spa/tub Applications
- Misuse, Abuse Or Tampering Whether Intentional Or Accidental
- Improper Installation Or Design
- Mproper Voltage
- Lack Of Normal Care
- Failure To Follow Instructions
3. CORROSION
4. FREEZING
5. ANY ADDITIONAL COSTS DUE TO CHANGES IN LAWS OR BUILDING CODES
6. FREIGHT CHARGES
7. ANY COSTS DUE TO LOST PROFIT OR DELAY
8. DAMAGE TO PROPERTY
9. CAUSE BEYOND CONTROL
10. DIRECT, INDIRECT, COLLATERAL OR INCONSEQUENTIAL DAMAGES OF ANY KIND
THE WARRANTIES AND LIABILITIES SET FORTH ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED IN LAW OR IN FACT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE
BaseAire’s total liability, regardless of nature of claim shall not exceed
original purchase
exceed original purchase price of the product, if a product or component is
replaced while under warranty, the applicable warranty period shall not be
extended beyond the original warranty time period
The foregoing shall constitute the total liability of seller in the case of
defective performance of all or any of the equipment or services provided to
buyer. Buyer agrees to accept and hereby
accepts the foregoing as the sole and exclusive remedy for any breach or
alleged breach of
warranty by seller.
Any dishonesty or fraud in connection with BaseAire warranty thoroughly voids
all warranty
policies. BaseAire expressly reserves the right to pursue legal action in the
event of dishonesty, fraud, or attempted fraud
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>