ZKTECO ZL700 Lock Body America Standard Mortise with 5 Latches Installation Guide

ZKTECO ZL700 Lock Body America Standard Mortise with 5 Latches

Important Notes

1. A new lock is defined as always in open mode until it is locked once by a IC card.
2. Please register an authorized card, a time sync card, and a room card initially for the new lock.
3. The lock is equipped with keys for manual unlocking. Remove the keys from the package and keep them in a safe place.
4. To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove the batteries when the lock is in working state.
6. When the battery power is low, the lock will beep to remind the user to replace the batteries. Make sure not to mix up the polarities while replacing the batteries.
7. Avoid contact with corrosive substances. Do not hang any object on the handle.
8. The built-in software manages the operation of access cards. Please refer the software user manual.

For further queries, please contact the seller.

Packing List

Note: This type of lock is suitable for a door thickness of 36 mm to 55 mm. If the door is thicker than 55 mm, this lock will not be suitable. Please contact the sales person for queries.

Installation Diagram

Installation Procedure

Check Opening Direction

Note : Please install the Mortise and Strike Plate according to the above illustration.

Drill Holes on the Door
Paste the Installation Template at the desired handle height. Mark for the holes to be drilled and drill the marked places.

Remove the Guide Plate

Unscrew the Screw A and remove the Guide Plate.

Installing Mortise

1. Make sure the side of Mortise without circle points is toward outdoor, then insert the Mortise into the drilled hole, secure it with Screw B.
2. Make sure the Cylinder toward Outdoor Unit, secure Cylinder with Screw C and Screw D by Hex Wrench A.
3. Secure the guide plate with Screw A, make sure the cable toward Outdoor Unit.

Note : Screw C has been secured in the Mortise before delivery.

Installing Outdoor Unit

1. Connect 6 PIN end of Transfer Cable with Mortise cable.
2. Insert a Spindle A into the clutch toward Outdoor Unit.
3. Attach the Outdoor Unit to the door by connecting 8 PIN end of Transfer Cable with mainboard on the drilled holes.

Installing Indoor Unit

1. Insert another Spindle A into clutch toward Indoor Unit, and insert the Spindle B into turn knob.
2. Secure the below of Indoor Unit with 2 Screw E.

Connect the cable of Battery Box with Transfer Cable, put in 4 Alkaline AA batteries, and insert the Battery Box into Indoor Unit. Secure the Battery Box and Indoor Unit with 2 Screw E.

Installing Strike Plate and Box

1. Make sure that the Strike Box is aligned with the latch bolt. Then, use the Installation Template to drill holes.
2. Align the Strike Plate and Box with the drilled holes and secure them with Screw B.

Test the Lock by Mechanical Key

1. Remove the cover on the key hole with the Vacuum Sucker.
2. Insert the key into the Cylinder and rotate it by 90°, then rotate down the handle to open the door, it means normal.

FCC

Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

• This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.

IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China.

• Phone : +86 769 – 82109991
• Fax : +86 755 – 89602394
• www.zkteco.com
• Copyright © 2022 ZKTECO CO., LTD. All Rights Reserved

References

• ZKTeco | Biometrics and Computer Vision

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>