Soundcore Life P2i True Wireless Earbuds User Manual
- June 6, 2024
- Soundcore
Table of Contents
Soundcore Life P2i
USER MANUAL
Charging
-
Remove the protective film from the earbuds before the first use.
-
Fully dry off the earbuds and the USB port before charging.
-
Use a certified USB-C charging cable and charger to prevent any damage.
-
Fully charge both the earbuds and the charging case before the first use.
1. Place the earbuds in the charging case and close it.
2. Connect the charging case to the power supply by using a USB-C charging cable. -
The LED indicator on the charging case indicates the charging status.
Wearing
- Choose the ear tips that fit your ears best.
- Insert the earbuds into the inner canal of your ears and turn gently until you find the most comfortable and secure position.
Your earbuds come with 3 pairs of ear tips, among which Medium-sized are pre- installed. 01 EN
Powering On/Off
- Open the charging case, the earbuds will automatically power on.
- To power off, place the earbuds into the charging case and close it.
- The earbuds will automatically power off after 10 minutes if no device is connected.
- To manually power on, press and hold the multi-function button on both earbuds for 3 seconds.
- To manually power off, press and hold the multi-function button on either earbud for 8 seconds.
Bluetooth Pairing
-
Open the charging case, the earbuds will automatically enter Bluetooth pairing mode.
The LED indicator on the charging case will flash white. -
Select “Soundcore Life P2i” on your device’s Bluetooth list to connect.
When successfully connected, the LED indicator on the charging case will turn off.
- When earbuds are out of the charging case and powered off, to manually enter Bluetooth pairing mode, press and hold the multi-function button on both earbuds for 3 seconds.
- Each time you power on your Soundcore earbuds, they will automatically connect to your last successfully connected device if available within the Bluetooth range.
- Mono mode: When Bluetooth is connected, you can use either one of the earbuds only by placing the other one into the charging case.
- When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.
- When you are on a call, place either one of the earbuds into the charging case, and the microphone in the other earbud will be activated.
Controls
Play/Pause| Press twice (R)
Next track| Press and hold for 2 seconds (R)
Previous track| Press and hold for 2 seconds (L)
Volume up| Press once (R)
Volume down| Press once (L)
Switch EQ| Press three times
Answer a call| Press once (L/R)
End a call| Press twice (L/R)
Reject a call| Press and hold for 2 seconds (L/R)
Activate Siri or another voice assistant| Press twice (L)
Mono mode
| Play/Pause | Press twice |
|---|
End a call
Answer a call| Press once
Reject a call| Press and hold for 2 seconds
**Reset
**
You might need to reset the earbuds if you experience any connectivity problems or function issues.
- Place the earbuds into the charging case and remain the case open.
- Press and hold the button on the case for 10 seconds until the LED indicator on the charging case flashes red 3 times. This confirms that the reset was successful and your earbuds can be connected normally.
Specifications
Specifications are subject to change without notice.
| Input | 5 V 0.5 A |
|---|---|
| Rated output power | 5 mW (@1% THD) |
| Battery capacity | 55 mAh x 2 (earbuds); |
500 mAh (charging case)
Charging time| 2 hours
Playtime
(varies by volume level and content)| Up to 8 hours
(Total 28 hours with the charging case)
Driver size| 10 mm x 2
Frequency response| 20 Hz – 20 kHz
Impedance| 16 Ω
Waterproof level| IPX5 (earbuds)
Bluetooth version| V 5.2
Bluetooth range| 10 m / 33 ft
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>