FS FIP-5112 Volp Phones with 2.8 Inch Color LCD User Guide

: June 6, 2024
: FS

Table of Contents

FS FIP-5112 Volp Phones with 2.8 Inch Color LCD
Introduction
Accessories
Hardware Overview
- Instruction of Keypad
**Installation Requirements
Mounting the IP Phone
Configuring the IP Phone
Basic Call Features
Support and Other Resources
Product Warranty
Documents / Resources

FS FIP-5112 Volp Phones with 2.8 Inch Color LCD

FS-FIP-5112-Volp-Phones-
with-2.8-Inch-Color-LCD

Introduction

Thank you for choosing the FIP-5112 IP phone. This guide is designed to familiarize you with the layout of the IP Phone and describes how to deploy the IP phone in your network.

Accessories

NOTE: There is no wall stand in the accessories of FIP-5112, therefore wall stand need to buy separately.

Hardware Overview

Instruction of Keypad

Table 1–Key Features

NO	BUTTONS	DESCRIPTION
4	Navigate/OK Keys	The user can press the up/down navigation key to

change the line or move the cursor in the screen list. On some Settings and text editing pages, the user can press the left/right navigation key to change options or move the cursor in the screen list to the left/ right.

OK key: Default is equivalent to soft button confirmation, user can customize the function.

5| Line key| Default to line 1/line 2, support the custom configuration of DSS key.
6| Volume Up/ Down Key| In the standby state of ringing and the ringing configuration interface, press this button to increase/reduce the ring volume; Press this button to increase/lower the volume on the call or volume adjustment screen.
7| Mute Key| During a call, the user can press this key to mute the microphone.
8| Standard Telephone Keys| The 12 standard telephone keys provide the same function as standard telephones, but further to the standard function, some keys also provide special function by long-pressing the key, Key# Long- pressed to lock the phone.
9| Headset Key| Users can press this key to open the headset channel.
10| Redial| Press the Redial key to redial the last number dialed.
11| Hands-free Key| The user can press this key to open the speakerphone.
12| Side Key| Long press the side key to enter the settings interface and set the required functions.

**Installation Requirements

**

Before you begin the installation, make sure that you have the following:

Store or use the device in a proper environment that meets environmental requirements, including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc.
Make sure the device is securely installed or placed on a flat surface to prevent falling.
Protect the device from liquid of any kind.
Make sure the power supply provides a stable voltage that meets the power requirements of the device.
Using the device may involve the collection of personal information such as phone number, GPS. Please abide by your local laws and regulations while using the device.

Mounting the IP Phone

Bracket Desktop Installation

Embed the stand into the phone.

Wall Mounting

Remove the sliding buckle and embed it in the opposite direction.
Fix the wall stand (buy separately) and embed it in the phone.

NOTE : Wall hanging bracket needs to be purchased separately.

Connecting to the Device
Connect the power adapter, network, PC, handset and headset to the corresponding ports.

Table 2–Hardware Interface Description

NO	Ports	Description
1	USB Port	Connecting USB Disk or USB WIFI Adapter
2	Power Port	Connecting Power Adapter
3	Network Port	Connecting to LAN or Internet
4	PC Port	Network Interface for Connecting Computer
5	Headset Port	Connecting Headset
6	Receiver Port	Connecting Microphone Receiver

Configuring the IP Phone

SIP configurations
A line must be configured properly to be able to provide telephony service.

Phone interface: To manually configure a line, the user can press the line key for a long time, or press the button in the function menu [Menu] >> [Advanced Settings] >> [Accounts] >> [Line n] configuration, click ok to save the configuration.
NOTE : User must enter correct PIN code to be able to advanced settings to edit line configuration. The default PIN is 123.
WEB interface: After logging into the phone page, enter [Line] » [SIP] and select SIP for configuration, click apply to complete registration after configuration, as shown below:

Network Configurations
The device relies on IP network connection to provide service. Unlike traditional phone systems based on a circuit-switched wire technology, IP devices are connected to each other over the network and exchange data in a packet basis based on the devices’ IP addresses.
To enable this phone, you must first correctly configure the network configuration.
To configure the network, users need to find the phone function menu button
[Menu] » [Advanced Settings] » [Network] » [Network].
The default password for advanced Settings is “123”.
NOTE : If the user saw a ‘WAN Disconnected” icon flashing in the middle of the screen, it means the network cable was not correctly connected to the device’s network port.
Please check the cable is connected correctly to the device and to the network switch, router, or modem.

Web Configurations
The phone can be configured and managed on the web page of the phone.

Enter the IP address of the phone in the browser and open the web page of the phone.
Enter the user name and password to log in to the web page.
NOTE : The default user name and password are “admin”.

Basic Call Features

Language Setting

Press Menu key> Basic> Language.
Select the desired language and press the OK soft key.

Making a Call

Pre-dialing: enter the phone number and pick up the handset.
Direct dialing: lift the handset and enter the phone number.
Handsfree: enter the phone number and press ••11) or vice versa.
Headset: enter phone number and press O or vice versa.
Designated line: press line key, enter the phone number and press dial key.

Accepting a Call

Using the handset: pick up the handset.
Using the headset: press Headphone).
Using the handsfree: press Volume).

Putting a Call on Hold

Press Pause Button the key or Hold a soft key, the caller is put on hold.
To retrieve the call press Pause key or Resume soft key.
NOTE : With more than one active call, select desired call with the use of the corresponding soft key to hold or resume.

3-party Conference

Once in line with 1st caller, press • key or Conf soft key, 1st caller is put on hold.
Then call the 2nd number.
After, 2nd call is established, press • key or Conf soft key to set up the conference

Call Transfer
Attended transfer:

Press H key or Xfer soft key during the active conversation, the call is put on hold.
Dial the second telephone number.
When the call is answered, then press the H key or Xfer soft key to complete the operation. Blind transfer:
- Press H key or Xfer soft key during the active conversation, the call will be on hold.
- Then enter the 2nd telephone number and press the H key or Xfer soft key.

Call Forward

Press Menu > Features> Call Forward.
Select the line, the type of forward, enter the destination number and status, and press OK soft key

Call Mute

1. Press the Button to Mute the microphone during the call.
2. Press the Button again to un-mute the conversation.

Call List

Press’Arrow key or Menu > Call Log > Local Call Logs.
Scroll through the list using Joystick.
To dial an entry, press Dial soft key or pickup handset or press() ori-I1

Phonebook
Access phonebook:

Press Arrow or Dir soft key or Menu > Contact > Local Contacts.
Select All Contacts or other Group.
To dial an entry, press Dial soft key or pickup handset or press Headphone or Volume).
Add new entry:
Press Dir soft key, Press All Contacts or other group > Press Add.
Enter name and number and press OK soft key.

Programmable Keys

You can configure shortcuts for the programmable keys.
Press Menu> Basic> Keyboard, select among the configurable items, and select your desired type and value, press OK key.

Do Not Disturb

Press DND soft key, and enable the device do not disturb mode.
Or press Menu > Features> DND, and select the Mode and Type, and press OK key.

Voice Mail

To access your voice mailbox, press Message Menu> Message> Voice Message, number of messages will be indicated if provided by your server or pbx.
Select the line and press Play to call.

Bluetooth

Press Menu> Basic> Bluetooth
Press OK soft key to enter the Bluetooth open interface. After opening, press Scan soft key to display the list of Bluetooth scanned. Select any device and press connect.

Wi-Fi

Plug the Wi-Fi Dongle. Press Menu> Basic> WLAN
Press OK soft key to enter the WLAN open interface. After opening, press Scan soft key to display the list of Wi-Fi scanned.
Press Enter soft key to enter the available Network, select the wireless network, press the Connect soft key and enter the password to connect.

Support and Other Resources

Download: https://www.fs.com/download.html
Help Center: https://www.fs.com/service/help_center.html
Contact Us: https://www.fs.com/contact_us.html

Product Warranty

FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a free return within 30 Days from the day you receive your goods. This excludes any custom made items or tailored solutions.

Warranty: IP Phones enjoy 1 year limited warranty against defect in materials or workmanship. For more details about warranty, please check at: https://www.fs.com/policies/warranty.html

Return: If you want to return item(s), information on how to return can be found at: https://www.fs.com/policies/day_return_policy.html

Documents / Resources

| FS FIP-5112 Volp Phones with 2.8 Inch Color LCD [pdf] User Guide
FIP-5112, Volp Phones with 2.8 Inch Color LCD, FIP-5112 Volp Phones with 2.8 Inch Color LCD
---|---