behringer XENYX X2442USB 24-Input USB Audio Mixer with Effects User Guide

behringer XENYX X2442USB 24-Input USB Audio Mixer with Effects

Important Safety Instructions

• Terminals marked with this symbol carry an electrical current of sufficient magnitude to constitute a risk of electric shock. Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installations or modifications should be performed only by qualified personnel.

• This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.

• This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

• Caution
  To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user-serviceable parts inside. Refer servicing to qualified personnel.

• Caution
  To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

• Caution
  These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

WARNINGS

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with a dry cloth.
7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by the manufacturer.
12.  Use only with the cart, stand, tripod, bracket,  or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15.  The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
17.  Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.
18.  Do not install in a confined space, such as a bookcase or similar unit.
19.  Do not place naked flame sources, such as lighted candles, on the apparatus.
20. Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed of at a battery collection point.
21.  This apparatus may be used in tropical and moderate climates up to 45°C.

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances, and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.

Installation

Step 1: Hook-Up

Step 2: Controls

Getting started

1.  Make sure the power to all devices is turned off!
2.  Connect all the appropriate power, audio, and USB cables to the mixer.
3.  Set all controls as shown above (EQ and PAN/BAL centered, all others down/off).
4. Turn the mixer on
5.  Set the GAIN for each channel. See the Gain Setting section for details.
6. With the MAIN MIX fader(s) and PHONES/CTRL ROOM knob all the way down, turn your PA system or powered monitors on.
7.  Adjust the relative level of various microphones and instruments by raising each CHANNEL FADER.
8.  Adjust the left-right position of a channel in the stereo field if necessary by turning the channel’s PAN or BAL knob.
9.  Adjust the COMP knob to add compression to input if necessary.
10. For live applications, adjust the overall output from the mixer to the power amp or powered speakers by raising the MAIN MIX fader(s). If the red CLIP LEDs on the VU METER light, lower the MAIN MIX fader(s).
11.  Use the channel AUX knobs and master AUX SEND knobs to send the channel signals to an effects processor or stage monitor connected to the AUX SEND jacks. If used for effects, route the signal back from the processor to the AUX RETURN jacks.

Gain Setting

1. (EN) Press the Channel 1 SOLO button. Press the MODE button next to the VU METER to allow the METER to operate in PFL

2. (EN) Sing, speak or play at a normal level through the microphone or instrument connected to Channel 1.

3. (EN) While singing or playing, turn Channel 1’s GAIN control. The VU METER will display the signal level. Set the GAIN control so that the loudest peaks reach 0 on the
   VU METER. Press the Channel 1 SOLO button again.

4. (EN) Repeat steps 1-3 for any other channels that will be used.

Multi-FX Processor

• Your mixer has a built-in effects processor. Follow these steps to add an effect to one or more channels.
•  Turn the FX knob up halfway on each channel to which you would like to add an effect.
•  Turn the FX SEND and FX RETURN knobs to 0. You may adjust them later.
•  Scroll through the effects by turning the PROGRAM knob. The preset number will flash in the display. Press the
•  Adjust the effect’s first parameter: After you have selected a preset (step 3), press the PROGRAM knob to enter Edit Mode. The right LED inside the display will start blinking. Turn the PROGRAM knob to adjust the parameter. After 5 seconds of inactivity, the mixer exits Edit Mode and the LED goes out.
•  Adjust the effect’s second parameter: If the effect’s second parameter is an on/off or toggled value, press the TAP  button to select between settings. 2 LEDs inside the display will start blinking. • If the effect’s second parameter is speed-based, press the TAP button in rhythm with the desired tempo. The TAP LED will flash to the current tempo. If ‘Lo’ is displayed, the tapped tempo is too slow. If ‘Hi’ is displayed, the tapped tempo is too fast. After 5 seconds of inactivity, the mixer exits Edit Mode and the LEDs go out.
• Readjust each channel’s FX knob to make sure the right amount of effect is added.

Multi-FX Processor Preset Chart

Specifications

Other important information

• Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
• Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
• Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

FCC Statment

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

XENYX X2442USB/X2222USB/X1622USB This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

• this device may not cause harmful interference, and
•  this device must accept any interference received, including interference that may cause undesired operation.

Important information
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU,Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive
1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark

References

• Music Tribe
• Music Tribe
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>