SVIVE PYX 35D601 35-Inch Gaming Monitor User Manual

PYX 35D601 35-Inch Gaming Monitor
User Manual

Safety Precautions

Do not place the monitor in the rain, humid environment or open the monitor case to avoid any shock, electrical hazards, and/ or mechanical hazards.

Operation

• Keep the monitor out of direct sunlight and away from stoves or any other heat source.
• Keep the monitor out of water.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics.
• Do not block the ventilation holes.
• Do not knock or drop the monitor during operation or transportation.

Maintenance Guidelines

CAUTION
Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.

Cleaning your monitor

• To clean your screen, slightly dampen a soft, clean cloth with water.
  If possible, use a special screen-cleaning tissue or solution. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.

• Use a slightly dampened, warm cloth to clean the frame. Avoid using detergent of any kind as some detergents might leave a milky film on the plastics.

• Unplug the monitor if you are not going to use it for an extended period of time.

• To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment. If your monitor gets wet, wipe it with a dry cloth as soon as possible.

HIGH-DEFINITION MULTIMEDIA INTERFACE
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in Norway and other countries.

Box Contens

Product Overview

Monitor Buttons

1. M Menu Button: Press to display the OS□ menu or enter sub-menus.
2. ▼ Down Button: Press to move down in the menus.
3. ▲Up Button: Press to move up in the menus.
4. E Exit Button: Press to exit.
5. Power Button: Press to tum the monitor on/off.
6. LED Indicator: changes color according to status.

Monitor Ports

7. Audio Output: Insert one end of the Audio cable into the computer’s audio output to receive the audio signals from your monitor.
8. DP Connectors: Insert one end of the DP cable into the computer’s DP output and connect the other end to the monitor’s DP port.
9. HDMI Connectors: Insert one end of the HDMI cable into the computer’s HDMI output and connect the other end to the monitor’s HDMI port.
10. Power Connector: Insert the power cable to supply power to the monitor.

Stand Installation

Make sure the monitor is laid on a flat surface before removing the stand.

1. First open the carton, take out the foam and align it on the desktop, remove the PE bag, and place the body on the foam. Press the lockdown vertically with your hand to remove the hinge assembly.
   

2. As shown in the figure, match the base with the bracket, and tighten the screws.

3. As above, vertically push the lock catch. Put stands assembly parts into the slot of the back cover accordingly and locks them in place.

During the process of assembling the screen, do not directly pinch the screen with your hands to prevent the screen from breaking.

VESA Mounting

This monitor only includes screws that may be used when attaching the monitor to a VESA 75*75mm type mount. No VESA mount or mounting accessories are included.

1. Open the package, take out the screen, still attached to the foam, and then gently place it on the table. Remove the upper styrofoam and place it on your desktop, do not remove the lower styrofoam from the screen, and remove the four screws on the backside.

2. Take out the wall mount adapter, lock the four PM4x12 screws and tighten it.
   • Do not discard the original screws.
   • Use only the provided 4 PM4 * 16 screws.
   

3. Your monitor is now ready to be attached to a wall-mounting bracket.
   To avoid damage, please do not pinch the screen during bracket installation.
   

Connectivity Options

1. Connecting the Power Cable
   Connect the included power cable to the power connector, and then plug the other end into a wall outlet.
   

2. Connecting Your Earphones
   Plugin your earphones to receive audio signals from your monitor.
   

3. HDMI Connectivity
   In order for the monitor to receive HDMI signals from the computer, use a HDMI cable to connect the monitor to the computer.
   

4. DP Connectivity
   In order for the monitor to receive DP signals from the computer, use the DP cable to connect the monitor to the computer.
   

Basic Operation

1. Insert one end of the DP cable into your PC’s graphics card. An HDMI cable may also, be used.

2. Connect the other end of the cable to the corresponding connector on your monitor.
   

3. Connect the power cable to your monitor then connect the other end to your power source.

4. Locate the power button on the monitor and press it to turn on the monitor.

Adaptive-Sync
This feature is off by default. To activate, you must have hardware with Adaptive-Sync capability, a DP or HDMI cable, and the latest graphic drivers. Alter connecting your omputer and monitor with a DP or HDMI cable, you may receive a prompt to enable the feature on your computer. If you do not, you may need to enable the function in your graphics card menu. See your graphics card manufacturer’s documentation for instructions.

Indicator Light

Solid blue light indicates power is on and the monitor is operating normally. Flashing blue light­ indicates no video source, no horizontal or vertical signal has been detected or voltage is low. Please ensure your computer is on and all video cables are fully inserted and/ or connected.

OSD

The On-Screen Display(OSD) Menu may be used to adjust your monitor’s settings and appears on the screen after turning on the monitor and pressing the M button.
When using the monitor for the first time, settings will automatically adjust to \;;.I optimal settings according to your computer’s configuration and parts etc.

1. Press any one of the buttons [ M, ▼, ▲, E, ] to activate the navigation window.
   

2. Press M ) to enter the OSD menu.
   

3. Press ▼or ▲browse functions.
   • Highlight the desired function, then press M to enter the sub-menu.
   • Press ▼or▲ to browse sub-menus, then press M to highlight the desired function.
   • Press▼ or ▲to highlight an option, then press M to confirm the settings and exit the current screen.

4. Press E to exit the current screen.

OSD Menu Functions

Set Gamma add-in
Gamma 2.0
Gamma 2.2
Gamma 2.4
Gamma 2.6
Picture Mode| Standard, Photo, Movie, Game,
FPS, RTS| Set visual mode according to activity
Color Temperature| Warm, Cool, User| Select color temperature
Low Blue Li • ht| 0-100| Set blue li.ht Merin. level
Hue| 0-100| Adjust hue levels
Saturation| 0-100| Adjust saturation levels
Picture
Quality
Setting| Sharpness| 0-100| Set display sharpness
Response Time| Off, High, Middle, Low| Adjust response time
Noise Reduction| Off, High, Middle, Low| Reduce the interference of image noise caused by signal source interference
Super- Resolution| Off, High, Middle, Low| When the resolution of the display
the screen is low, this function can be turned on to enhance the image resolution
Dynamic Luminous Control| On, Off| Compensate for grayscale display screen and strengthen the expression of
grayscale
OverClock| On, Off| Open OverClock under the DP port and the refresh rate is increased to 180Hz: Overclock gray is not optional on the HDMI port.
Display| Aspect Ratio| Wide Screen, 4:3, 1:1, Auto| Select the on-screen aspect ratio
Audio| Mute| On, Off| Turn mute mode on/off
Volume| 0-100| Adjust audio volume
Audio Source| DP1, DP2, HDMI 1, HDMI 2| Select audio signal input via HDMI or DP
Main Menu| Sub-Menu| Options| Description
---|---|---|---
Multi-Window| Multi-Window| Off, PIP Mode, PBP 2Win| Select PIP/PBP modes according to the number of input signals etc.
Sub Win2 Input| DP 1, DP 2, HDMI 1, HDMI 2| Select according to an input signal for PIP/ PBP mode
PIP Size| Small, Medium, Large| Adjust the PIP/PBP display window size
PIP Position| Top Right, Top
Left, Bottom Right, Bottom Left| Adjust the PIP/PBP window position
Swap| NONE| Swap the two-channel signal source of only the PIP/PBP 2 screens function
OLD| Language| English, 04 fd–cii, Pyccionl, Espanol, 9* it, Francais| Set OSD language
OSD H-Position| 0-100| Adjust the OSD’s horizontal position
OSD V-Position| 0-100| Adjust the OSD’s vertical position
05D Transparency| 0-100| Set the OSD’s overall transparency
OSD Time Out| 5-100| Set how long the OSD remains open after non-use
OSD Rotation| Normal, 90, 180, 270| When the user flips the display, this function can also flip the OSD to achieve the best display angle
Other| DP Version| DP1.1, DP1.2, DP1.4|
Adaptive-Sync| On, Off| Turn the Adaptive-Sync function on/off
HDR| On, Off; Auto-Detect| Turn the HDR mode on/off
Reset| None| Reset monitor configurations

ECO Modes and Game plus

1. Press any of the buttons[ M,▼,▲ , E, ] to activate the navigation window.
   

2. Press▼ the button to switch Game plus modes. According to the needs of your game, choose the corresponding game icon. These game icons are primarily designed to optimize your aim during shooting games, though they can be used for other scenarios.
   

3. Press ▲the button to switch ECO modes. These modes include Standard, Text, Movie, Game, FPs, and RTS and can be used to optimize settings according to your activity. Standard mode is suitable for most activities.

4. Press E to switch color gamut mode between “Limited” and “Full” when the optimal configuration is used.

Specifications

Audio
Speakers| No
Audio Out| Yes
|
Accessories
Power| AC 100-240V– 50/60Hz 2.0A
DisplayPort Cable| Yes
Power Cable| Yes
Additional Functions|
Low Blue Light| Yes
Flicker-Free| Yes
Physical Dimensions
Dimensions (w/ Stand)| 837.4245.6539.8mm
Dimensions w/o Stand| 837.4126.1377.9mm
Net Weight| 8.1kg
Gross Weight| 11.7kg

Imported by Svive, (stre Kullerad 4,
N-3241 Sandefjord, Norway
Made in China I www.svive.gg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>