TOGUARD CE13 Dual Lens Rearview Mirror Dash Cam User Manual

: June 6, 2024
: TOGUARD

Table of Contents

Overview
Specification :
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TO GUARD CE13
Dual Lens Rearview Mirror
Dash CamUser Manual

Important Notice:

This product is intended for use in motor vehicles only Do NOT install the camera where it might block the driver’s view of the road (including the mirrors) or the deployment of the airbag.
Before using this camera, please insert the memory card first, and format the memory card in the camera menu first.
This camera records video at high resolution, Be sure to use a high-speed Micro SD card, Class 10 or above is recommended, 16GB or 32GB cards are recommended.
For safety reasons, this camera has a small built-in battery, It’s used only for saving the video file after the external power supply cuts off (the car turns off).
Be sure the camera lens is clean and there is nothing blocking the lens.
DO NOT leave the camera in direct sunlight for a long period of time or where the temperature could go above 1707(75°C).

Overview

Main Interface and Touch Screen Function

Clock / Time Setting
Video Recording Mode
Photo Mode
Playback
Manual Lock Current Video
Mute Audio Recording
Power OFF
Format memory card

Set up and Installation:

Before installation, please check the camera’s normal function, make sure you are using a high-speed Micro SD card (speed Class 10 or above.), and format the card in the camera menu before recording.
Mount the camera over the original rearview mirror and use the included rubber rings to fix it, make sure the camera is in place, and fasten.
Adjust the mirror angle according to your driving position, make sure the mirror is right in place and the view is clear.
Adjust the lens angle of the camera, make sure you get the best coverage over the hood and the road ahead, so you can record what happens.
Connect the power to the camera and the cigarette lighter, hide the rest of the cable in the gap of the Interior trim board.
The rear camera should be installed above the number plate, screw pad upward, connect the red power cable to the reverse lamp wire positive lead.
Route the camera cable to the front of the car, and connect the rear camera to the main device. There are 2 pictures for reference.
Start the engine and leave a test run.

Setting Menu and Featured Functions

Return to Main Interface
Memory Card Status
Video Resolution
Recording Time
Power Status
Rearview Camera
Mute Audio Recording.
Manual Lock
Start/Stop Recording
Picture in Picture Mode Switch
Setting Menu

Video Recording Menu:
Resolution: Adjust the recording video resolution, 1080P/ 720P/VGA available
Loop Recording: This function allows you to set video file length to 1/2/3minutes, Select a value to activate loop recording, so when storage fills up, it will automatically loop back to the earliest file and record over it.
Enhanced Night Vision: turn on to optimize video quality with wider light range and image details.
Switching stone: Turn on and off the power-on and power-off prompt.

Date Stamp: Enable/Disable the date and time marks in video files.

Gravity Sensing: G-sensor will detect significant or sudden shock and movement then automatically locks current recording from loop recording, Low/medium/High sensitivity available.
Parking Monitor: It’s used to protect your car after parking, with this function on, after you stop the car and the camera turns off, it stays on standby, when the camera detects shacking, it will automatically turn on and take a short video, then shut down automatically.
Anto Power Off: Set the time for the camera to automati-cally power to save energy, after the camera is idle for a set time, it will power off.
Language: English/French/ Spanish/ German/ Italian/ Russia/Japanese available.
Frequency: Set light frequency to 50Hz or 60Hz, and press OK.
Format: Format the Micro SD card.
Screen Saver. Set the time to automatically turn off the LCD display after no operation.

Off-Screen Clock: Turn ON/OFF the time display after the screen saver is activated.
Date/Time: Change the time and date by using the UP and DOWN button, then press OK to confirm.
Default Setting: Reset all settings back to factory default. Version: Check the firmware version.

Photo Mode Interface and Setting Menu

Return to Main Interface
Memory Card Status
Photo Resolution
Remaining Storage
Power Status
Rearview Camera Switch
Take Photo
Setting Menu

Resolution: Set the photo resolution, Up to 3 Mega Pixels available.
Quality: Defines the quality of image you capture, Fine / Normal / Economy available.
Anti-Shaking: Turn ON/OFF the image stabilization function.
Date Stamp: Enable/Disable the date and time marks in image files.
ISO: Adjust the ISO value to adjust the brightness of the video. Sharpness: Defines the clarity of details in the photos. Language: English/French/ Spanish/ German/ Italian/ Russia/Japanese available.
Frequency: Set light frequency to 50Hz or 60Hz, and press OK.

Common Problems and Solutions:

The dashcam will stop automatically when recording. Solution:
(1) Check whether the memory is full.
(2) Check whether the loop recording function of the dashcam is working.
(3) Check whether the Micro SD card is high-speed above C10
(4) Check the memory card, there might be too many locked videos that the loop recording won’t work right.
If the video played on the computer is somehow not fluent or jammed. There might be some problem with the memory card.
Solution:
(1) Format your Micro SD card in the camera.
(2) Change one high-quality card
There is stripes interference in the image. There should be a wrong light frequency. Solution: According to the local main frequency, make the appropriate settings 50HZ or 60HZ
When the video play on your computer, the video will pause. Or the video mode is not compatible with the player. Solution:
(1) The Micro SD card does not suit this dash camera, please try with another memory card.
(2) Use some other media player.
Without an external power supply, the camera only lasts a very short time, or it just can’t turn on.
Solution: The built-in battery is very small for safety reasons, not designed to work alone, so please keep it connected to the external power supply.

Specification :

Model	TO GUARD CE13
Image Sensor	High-Resolution CMOS Sensor
Screen	4.3 inch LCD Display
Lens	170°High Resolution Wide Angle Lens
Video Resolution(Front):	19201080P(Front Lens Only)/ 1280720P(Dual