TOGUARD CE80A Touch Screen Streaming Video Rear View Mirror User Manual

SIZE:90mm X 120mm : : :
PANTONE Black C
CE80A
TOUCH SCREEN STREAMING
VIDEO REARVIEW MIRROR

If you have any other questions or problems,please feel free to contact us at support@toguard.cc
We have a professional team at your service, and your satisfaction is guaranteed.
V20201224

Important Notice:

• NOTICE: Due to the high power consumption of this unit, it should always be connected to an external power supply we provided inside the package. This camera should not power on without an external power supply connected.
• This product is intended for use in motor vehicles only. DO NOT install the device where it might block the driver s view of the road (including the mirrors) or the deployment of the airbag.
• Before using this device, please insert the memory card first, and need to format the micro SD card to FAT32 format on PC first, then format the memory card in the camera menu.
• This device records video at high resolution, Be sure to use a high-speed memory card, U3 or above is recommended, 16GB or 32GB cards are recommended.
• We do recommend doing a benchmark test and making sure the unit is working perfectly before installing the unit on your vehicle.
• Be sure the lens is clean and there is nothing blocking the lens.
• Make sure you are using the originally included power adapter to power the unit.
• DO NOT leave the device in direct sunlight for a long period of time or where the temperature could go above 170°F(75°C).
• The GPS function have to work with a customized GPS module, please download “GX player”. Please contact the seller for details.

Installation Guide

1. Before installation, please insert a high-speed memory card in the unit and format the memory card in the unit set, also do a simple test to make sure the unit is working perfectly.

2. Mount the mirror over the original rearview mirror and use the included rubber ring to fix it. Make sure the mirror is in the right place and secured.

3. Adjust the mirror angle according to your driving position, make sure the mirror is right in place and the view is clear.

4. Adjust the angle of the lens. Make sure you get the best coverage over the hood and the road ahead, so you can record what happens.

5. Connect the power adapter to the mirror and the cigarette lighter, then routes the power cable along with the interior trim board, you can route it as indicated below, and hide the excess cable in the gaps for good-looking.

6. The rearview camera should be installed at the rear end of the car, normally the best place is above the number plate. The camera can be fixed with a sticker or a screw. You can see the diagram for reference.
   (NOTE: Please check whether the backup camera is installed upside down before you install screws.)

7. The excess RED lead near the rearview camera is used for reverse status sensing. Connect the RED cable to the positive lead of the reverse lamp power.

8. Route the backup camera cable to the front of the car and connect it to the main unit. There are 2 pictures for reference.
   (NOTICE: Holes might need to be drilled to pass the cable and please check whether the cable for the backup camera is long for your car before you install it.

9. After the installation is completed, please start the engine and have a test run, making sure all functions are working.
   NOTICE: The wiring and the installation requires certain handwork and some professional electrician skills, if you are not sure about it, please get some professional help.

Adjust the Reversing Camera

Adjust the reversing camera angle, the best angle is the camera can cover the rear of the car and the ground surface under the rear end.
NOTICE: When the car is in reverse, the rear camera will automatically display in full screen, and turn to the lowest angle, so you can see the ground surface under the rear end while reversing.

Interface and Button Functions

1. Touch screen
2. Securing clip
3. Mini USB
4. Real camera interface
5. Memory card slot
6. GPS interface(Optional)
7. Power
8. Reset
9. Lens

Power button

NOTICE: Due to safety reasons and the high performance of the CE80A mirror, the power consumption of the CE80A is relatively high, it should always be connected to an external power supply to ensure working normally.

Power On/ Power Off
Long press the power button for 3 seconds to power off the unit.

Turn off / Tum on Screen Display
When the unit is on, short press the power button to turn off the screen display, enter the power saving mode(the recording is still working with screen off); Short press the power button or touch the screen to reactivate the screen display again.

Reset button
if the recorder somehow crashes or malfunctions, press the (RESET) key to reset the unit and press the (POWER) button again to restart the device.

The main interface and Operations

When the mirror is powered properly, when you start the car engine, the unit will automatically power on and start recording. In the video recording interface, touch the screen to call up the tool bar.

| Click to turn ON/OFF audio recording in video.
---|---
| Click to take a photo.
|  Click to start/stop video recording.
|  Click to enter Setup menu.
|  Click to manually lock the current video.

Shortcut Operation

In the recording interface, there are several shortcut operation:

1. In the recording interface, slide horizontally to the right to enter Playback Mode.
2. In the recording interface, slide horizontally to the left to switch Front and Rear camera display mode.
3. In the main recording interface and on the Right side of the screen, slide vertically up and down to adjust screen brightness.
4. In the main recording interface and on the Left side of the screen, slide vertically up and down to move lens view angle.

Playback Mode

1. Return to the video interface.
2. Front video folder.
3. Rear video folder.
4. Front lock recording folder.
5. Rear lock recording folder.
6. Front photo folder.
7. Rear photo folder.=

1. Delete selected files
2. Lock selected file
3. Select all
4. Unlock selected files
5. Video file, click to play
6. Turn page
7. Turn page
8. Return to the previous menu

Setup Menu

CAdamjusetrav,idRefooreresoalructaiomne, rFaf.or Front
Loop Record| 15 mins/ 3 mins /| lAednjgutsht.Loop Recording video clip
Record Audio| OFF / ON| Turn-ON / OFF audio recording.
G-Sensor| high/ Low / Middle / OFF / Low / Middle /| Adjust G-sensor lock sensitivity.
Parking Guard| High| Adjust Parking Guard sensitivity.

Setup your car license plate number,

License| Adjustable| and watermarked in video.
Screen Saver| O5 FmFin/ s1 min / 3 mins/| tSiemtuep. the screen saver activated

Video Encode

| ****

H.264/H.265

| UAjnudstervitdheeofreonncto4dKer.ecording, the svwidietcoheendcodingformat cannot be
Frequency| 50Hz / 60Hz| Setup local power frequency.
Key Voice| ON / OFF OFF/ Low / Middle| Turn-ON / OFF operation prompt.
Speaker| / High| Adjust the speaker volume.
Boot Sound| ON / OFF| nTuortnifiOcaNti/on.FF system boot up
Stream Media| ON / OFF| Turn-ON / OFF streaming media mode.
Language| English / Chinese / Japanese / Russian / German / French / Spanish / Italian| Setup the system menu language.
Setup| Option| How it works
---|---|---
Date/Time| Adjustable| Set up local date and time.
Default Setting| Cancel / Confirm| aFollrdmaatat.the memory card and delete
Default| Cancel / Confirm| sRteasttuosr.e the mirror to factory default
Time Zone| Adjustable| ySoeuturplotchaetitoimn.e zone according to
Voice Command| ON / OFF| Turn-ON / OFF Speech Recognition.
Version| | Check the software version.
GPS test| | Test GPS signal
Speed Calibration| Adjustable| Precision speed
Speed Unit| KM/H or MP/H| Speed unit adjustment

Featured Function

Dual Recording
The CE80A mirror comes with a dual-channel lens, they can record video in Front 4K (28802160)+ Rear 1080P (19201080) simultaneously.

Loop Record
This function allows you to set video file length to 1/3/5 minutes, Select a value to activate loop recording, so when storage fills up, the CE80A will automatically loop back to the earliest file and record over it.

EG
If set the time 3 minutes, then the unit will keep recording video in 3 minutes clips, When the card is full, the unit will keep recording and overwrite the earliest unprotected 3minutes video file and so forth.

G-Sensor
The CE80A has a built-in Gravity sensor, In the event of a serious vehicle collision or rapid acceleration/deceleration, the G-sensor will be triggered and immediately lock the current video file so the file will not be overwritten by loop recording.

Parking Guard
The Parking Monitor is used to protect your car after parking, with this function on, after you stop the car and the unit turns off, it stays in standby, when unit detects significant shock, it will automatically turn on and take a 20 seconds short video, then shut down automatically. Video recorded under the parking monitor will be protected and will not be overwritten by loop recording.

Screen Saver
Set the time after which the unit will automatically turn off-screen. Used to save power and reduce distraction while driving. For example, it is set to 3 minutes, if the unit is not operated in 3 minutes, the unit will automatically turn off-screen while the recording is still working, any button operation or touch the screen will reactivate the screen display.

Voice Command
The CE80A features a Speech Recognition function. You can use the specified Speech Recognition to complete certain operations. With Speech RecognitionFunction on, the CE80A mirror will act by the command you said according to the user manual.

The operation and Voice command are as follow:

The mirror will display the front camera view in

front video on| full smcrierreonr. will display rear camera view in
real video on| full screen.
take photo| The Mirror will take a photo.
record video| Start recording.

NOTICE: The Voice Command function is greatly affected by the accent. Try reading the commands loud and clear.

Streaming Media
The CE80A mirror features a Streaming Media function, with this function on, the camera will display the rear camera view in full screen as default, It will work as a real rearview mirror.
GPS Function
With the optional GPS module connected, the CE80A can display the current speed on the screen. You can enter the setup menu and check the GPS signal status. The speed unit KM/H and MPH is optional.
NOTICE
The speed displayed is an average speed calculated based on the locations and time, there might be certain errors, especially under low speed. It’s for reference only.
GPS Logger
With the optional GPS module connected, the CE80A can record real-time GPS coordinates in the video file, it can be reviewed with the customized GPS player.
NOTICE
The GPS playback needs a customized player “GXPlayer” (Please contact seller support to get it ), for the Windows operating system only.

Specification:

Common Problem and Solution

The recorder shows memory full, unable to loop video, etc.

1. First, when a new memory card is used for the first time on the machine. Please format the memory card to FAT32 format on the PC then format it in the camera.Or the memory card is previously used on another type of device,it needs to be formatted when used on this camera.Or change to another new SANDISK 32G Micro SD CARD.
2. Check the sensitivity of the G-sensor, If the sensitivity is too high,the bumping and shaking of the camera will trigger the G-sensor, and the file will be locked. Locked files cannot be overwritten.If the lock file is accumulated, there will be no memory card to loop the record. When parking monitoring is turned on, shaking will also cause too many stray files, which will also affect the reading and writing of cards.

The device will automatically turn on or turn off.

1. Please format the memory card to FAT32 format on the PC then format it in the camera. 2. Please check whether the parking guard function is on. With a parking monitor on, the device will automatically turn on and record when it detects a collision or shaking. 3. Check the car charger connection status, if the connection is loose, the power supply is not stable, and the camera will automatically turn on and off.

The rear camera does not display the image

1. Please switch the camera display mode to double-check the rear camera status.
2. Please check if the AV plug is properly connected and the cable is plugged incorrectly.
3. Try to disconnect the camera and clean the connector with some Medical alcohol connect it again.

Screen operation or button reaction is slow during recording

1. Please check whether the memory card used is a high-speed card ((J3), If you use a non-high-speed card, problems such as missed seconds, video playback jams, screen display Colorful stripes, and crashes may occur.
2. Reset the camera if necessary.

Even though set the screen saver, but the screen will randomly come back on.
The power supply might not be stable, please change another car charger to try.

support@toguard.cc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>