TOGUARD C200 4K UHD Dash Camera User Manual
- June 6, 2024
- TOGUARD
Table of Contents
TOGUARD C200 4K UHD Dash Camera
Important Notice
-
This product is intended for use in motor vehicles only. Do NOT install the camera where it might block the driver’s view of the road (including the mirrors) or the deployment of the airbag.
-
Before using this device, please insert the memory card first, and need to format the micro SD card to FAT32 format on PC firstly, then format the memory card in the camera menu.
-
This camera records video at high resolution, Be sure to use a U3 or above high-speed Micro SD card. Support
128- 256GB cards. -
The C200 uses a supercapacitor instead of a lithium battery as a power source, which is safer and lighter, It is only used to save the last video after a power cut. The camera will not power on without an external power supply.
-
Be sure the camera lens is clean and there is nothing blocking the lens.
-
DO NOT leave the camera in direct sunlight for a long period of time or where the temperature could go above 140°F(60°C)
Interface and Button Function
- lens
- Screen
- MODE
- UP
- 0K
- DOWN
- MENU
- Power
- Mount Slot
- Mini USB
- AV
Button Function
Set up and Installation
- Use the Suctionc up mount to install the C200 dash cam on the windshield, recommended place near the rearview mirror facing front, adjust the lens angle for best coverage.
- Plug the included power adapter into the car cigarette lighter socket, the indicator will light up meaning power is on.
- Connect the power cable to the camera. For better looking, route the excess cable alongside the interior trim as the diagram shows.
- Install the rear view camera on the rear windscreen (inside the car), adjust the lens angle for best coverage, then connect the rear camera connector to the main unit.
- After installation, please start the engine, and do a bench test to make sure all function works well.
Operating Mode
The C200 operates in 3 modes: Video Recording Mode, Photo Mode and Playback
Mode. These modes also have menu to help you configure recording .
Press MODE button to switch between different modes and access the mode you
want. Watch the icon on top left corner of the screen for each mode.
Video recording Mode
The camera will automatically enter Video Recording Mode and start recording
when connected to a car charger and power on.
A Red dot flashing on the top left corner indicates recording is inprogress.
Press the OK to stop recording, or start recording again.
- Mode
- Loop Recordiing
- G-sensor
- Lock video
- Time&Date
- WDR
- Recording Time
- Video Resolution indicator
- Audio Recording
- SD card
- Power
- In this three modes, you can enter the setting mode by pressing the MENU button.
- Press the UP or DOWN button to select the setting option,
- press the OK button to confirm, press the MENU button again to exit the setting option.
Video Recording Menu
Resolution
Adjust front lens recording video resolution,4K 30FPS/
2K 30FPS/1080P 30FPS available.The rear camera will record in 1080P only.
Loop Recording
Off/ 1 / 3 / 5 Minutes. This function allows you to set the recording video
file length to 1/3/5 minutes to automatically overwrite the earliest file when
the SD card’s storage fills up. We recommend you turn on the loop recording
function to prevent the memory card space runs full and stop recording.
(1-minute settings default).
WDR
ON/OFF. Wide Dynamic Range: turn on to optimize video quality with wider light
range and image details.
G sensor
OFF/ Low/ Middle/ High. G-sensor will detect significant or sudden shock and
movement then the camera will automatically lock the current recording file
from loop recording, detection sensitivity can be adjusted accordingly.
Exposure
+2/ .. ./0/ .. ./-2. Adjust video brightness
Motion Detection
Off/on. Turn ON/OFF motion detection function. For your safety, we highly
recommend turning off this function.
Record Audio
Off/on. Turn recording on and off.
Date Stamp
Off/on. Enable/Disable the date and time marks in video files.
Parking Monitor: (Optional)
With optional hard wire kit connected, the Parking Monitor is enabled, the
camera will stay standby after the engine is turned off. When camera detects
shaking, it will automatically turn on and take a short video, then return to
standby automatically. (Must use the hardwire kit when using the Parking
Monitor function.)
Photo Taking Menu
Resolution
12M(4032X3024)/10M(3648X2736)/8M(3264X2448)/ 5M(2592X1944)/3M(2048X1536)
Date Stamp
Off/on. Enable/Disable the date and time marks in photo files.
Playback Mode:
This mode allows you to playback recorded video or view photos, and manage the
recorded files.
- Stop the video recording, press the MODE button twice to enter Playback Mode, you can view all the files in this mode.
- In playback mode, the folders are displayed in the following order:
- Rear Camera Video
- Front Camera Video
- Use the UP and DOWN button to scroll through the recorded files / photos, and press OK to play or pause playing the selected file.
- Press MODE button to quit playback and return to file list.
- Use the Playback Menu to manage the files. Press Menu button to enter setup menu.
Playback Mode Setup Menu
Delete: Delete the recorded files.
Protect: Use this option to Lock and Unlock files, locked files will not
be overwritten by loop recording. Slide show Select a time gap to activate
this function and all. The recorded file will be displayed in slide show.
Specification
Common Problems and Answers
The dash cam will stop automatically when recording. Solution:
- Check whether the memory is full.
- Check whether the loop recording function of the dash cam is working.
- Check whether the Micro SD card is high-speed above U3
- Playback the recorded video on dash cam to check whether there might be to many locked videos, which cause the SD card space run out and stop looping recording.
If the video played on the computer is somehow jammed or not fluent. There
might be a problem with the memory card speed.
Solution
- Format your Micro SD card in the camera.
- Change a U3 or above high-speed Card.
There are stripes interference in the video. Solution: There should be
wrong light frequency. According to the local main frequency, make the
appropriate settings 50HZ or60HZ.
support@toguard.cc
Suction mount cannot attach on windshield well?
Solution
- Please clean the windscreen where attaching with a glass cleaning wipe. Removed the protective film, If it does not work, warming your windscreen then try it again.
- Please soak suction mount to warm water for a moment.
- If it is still not working, we are glad to send a new suction mount to you, please contact us to get a replacement.
Without external power supply, the camera will not power on, or the camera
will power off immediately after the external power supply is disconnected.
Solution
This C200 dash cam needs a 5V 2A external power supply to be power on. The
camera will not power on without external power supply. Because the power
source of this C200 dash cam is a safer lighter super capacitor instead of
lithium battery, which is only used to save the last video after power cut.
support@toguard.cc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>