Shelly E26 Duo Smart Bulb Instruction Manual
- June 6, 2024
- Shelly
Table of Contents
Shelly E26 Duo Smart Bulb
The Shelly DUO (WW/CW or RGBW model) smart WiFi LED bulb by Allterco Robotics is intended to be installed into a standard light socket (E27/E26 or GU10) in order to change the white temperature or color (depending on model) and to dim the light. Shelly may work as a standalone device or as an accessory to a home automation controller.
Specification
| Power supply | 110-230V ±10% 50/60Hz AC |
|---|---|
| Socket | E26/E27 |
| Power Rating | 9W |
| Brightness | Up to 800 lm |
| Color Temperature | WW/CW (2700K-6500K); RGBW |
| Beam Angle | 190° |
| Working temperature | From -20°C to 40°C |
| Complies with EU standards | RED 2014/53/EU, LVD 2014/35/ EU, EMC 2004/108/WE, |
RoHS2 2011/65/UE
Radio signal power| 1mW
Radio protocol| WiFi 802.11 b/g/n
Frequency| 2400 – 2500 MHz;
Operational range (depending on local construction)| up to 30 m outdoors up to
15 m indoors
Dimensions| 60×122 mm| 50×73 mm
Electrical consumption| < 1 W
Technical Information
- Control through WiFi from a mobile phone, tablet, PC, automation system or any other device supporting HTTP and/or UDP protocol
- Microprocessor management
- Controlled elements: multiple LED diods
- Shelly may be controlled by an external switch
CAUTION
Danger of electrocution. Plugging the device to the power grid has to be
performed with caution. Do not allow children to play with the device. Keep
the devices for remote control of Shelly (mobile phones, tablets, PCs) away
from children. Please handle with care! The Shelly® DUO is FRAGILE!
Introduction to Shelly
Shelly® is a family of innovative Devices, which allow remote control of
electric appliances through mobile phone, PC or home automation system.
Shelly® uses WiFi to connect to the devices controlling it. They can be in the
same WiFi net-work or they can use remote access (through the Internet).
Shelly® may work standalone, without being managed by a home automation
controller, in the local WiFi network, as well as through a cloud service,
from everywhere the User has Internet access.
Shelly® has an integrated web server, through which the User may adjust,
control and monitor the Device. Shelly® has two WiFi modes – access Point (AP)
and Client mode (CM). To operate in Client Mode, a WiFi router must be located
within the range of the Device. Shelly® devices can communicate directly with
other WiFi devices through HTTP protocol. An API can be provided by the
Manufacturer. Shelly® devices may be available for monitor and control even if
the User is outside the range of the local WiFi network, as long as the WiFi
router is connected to the Internet. The cloud function could be used, which
is activated through the web server of the Device or through the settings in
the Shelly Cloud mobile application.
The User can register and access Shelly Cloud, using either Android or iOS
mobile applications, or any internet browser and the web site:
https://my.Shelly.cloud/.
Installation Instructions
CAUTION
Danger of electrocution. Before installing the Device into the light socket
please check if it has been powered off. Before beginning the installation
please read the accompanying documentation carefully and completely. Failure
to follow recommended procedures could lead to malfunction, danger to your
life or violation of the law. Allterco Robotics is not responsible for any
loss or damage in case of incorrect installation or operation of this device.
Use the Device only with a power grid that complies with all applicable
regulations. A short circuit in the power grid connected to the Device may
damage the Device. Please check the working voltage of the device and the
supplied voltage of your power grid before installing the device! Installing
the device to a non-recommended power supply may lead to malfunction, danger
to your life or violation of the law. Allterco Robotics is not responsible for
any loss or damage in case of incorrect installation or operation of this
device.
RECOMMENDATION
The Device may be connected to and may control electric circuits and light
sockets only if they comply with the respective standards and safety norms.
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly
DUO is in compliance with Directive 2014/53/EU, 2014/35/EU, 2004/108/WE,
2011/65/UE. The full text of the EU declaration of conformity is available at
the following internet address: https://shelly.cloud/declaration-of-
conformity/Manufacturer: Allterco Robotics EOOD Address: Sofia, 1407, 103
Cherni vrah Blvd. Tel.: +359 2 988 7435 E-mail:
support@shelly.cloud Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official
website of the Device: http://www.shelly.cloud The User is obliged to stay
informed for any amendments of these warranty terms before exercising his/her
rights against the Manufacturer. All rights to trademarks She® and Shelly®,
and other intellectual rights associated with this Device belong to Allterco
Robotics EOOD.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>