MegaLight 25032021 Wi-Fi and Bluetooth Smart Strip Instruction Manual
- June 6, 2024
- MegaLight
Table of Contents
MegaLight 25032021 Wi-Fi and Bluetooth Smart Strip
Hereby, MAUAGmbH dedares that the radio equlpmenttype Mega Light Smart Device Is In compliance with Directive 2014/53/EU. The full text of the EU declaration conformity is available at the following internet address: mega- llghtde/declaration-of-conformity Details for Wireless radio used in MegaUght Smart lamp luminaires/ devices/components Wireless protocol: 802.11 b/g/n: transmitting frequency band: 2400-24835MHz, the max transmitting power Is : 17.9dBm. Bluetooth 4.0 with Blf: transmitting frequency band: 2400-24835MHz. the max transmitting power Is : 83dBm. To comply with RF exposure requirements, the device and the antenna for this device must be installed to ensure a minimum separation distance of 20 cm or more from a person’s body.
PARAMETERS
COLOUR| INPUT VOLTAGE| OUTPUT VOLTAGE(DC)/
CURRENT(MAX)
| MErER
---|---|---|---
us IEU/AU/EN
WHITE| 100-120Vl220-2-40V| 12V/2A| Sm
RGB| 100-120v1220-2-40v| 12V/2A| Sm
RGB+WHITE| 100-120v1220-240v| 12V/1.5A| 3m
- Use DC12Vpower supply.
- Install the Wi-fi & Bluetooth controller correctly. Use 3M tape to fix it.
- Please unfold the LED strip to ovoid the overheat issues. Please connect the cables of LED strip with the right position on the controller. Test the APP to check if it can control the LED strip correctly. If everything goes well, just keep going.
- Check and ensure the power supply, WIFI controller and LED strip are connected correctly.
ATTENTIONS
- Do not put any metal around the WIFI controller, which could blocked WIFI signal.
- Ensure power supply and controller are connected correctly.
- The power supply output voltage should be same asLED strip working voltage.
- Do not cover anything on the surface of power supply, WIFI controller and LED strip.
- Ensure the connection is correct before powering.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.
**PRODUCT FUNCTIONS DIAGRAM
**
- DC 12V input connection port
- Output connection port to connect to LED strip
- Function buttons:
Press the button once: turn on your device.
Press the button twice: tum off your device.
Press the button for 6 seconds: reset your device.
Press the button quickly once: change to your
favorite scenes.
| LEOSTRIP’ltHfTE| LEOSTM’RG8| LEDSTRJPRGB+WIITE
---|---|---|---
| lritilil-..tllelfght 60%,
ac,llingllalhes
| lnlial bl.ieligh1 50%,
li,rtingll!lshes
| lritial blul light 50%,
�flllllha
| | Gr-,lgh1100% brighlnesa| Whltellgh1100% brlghlMH
REMOTE CONTROL
LED STRIP CUTTING
The flexible LED Strip can be shortened with a scissor at the marked positions.
DOWNLOAD APP
1 Search “Tuya Smart” from App store or Google play.
2 Scan the QR code from the label or user manual.
3 The APP is compatible with Android 4,0 and IOS8.1 and higher version.
LOG IN / REGISTER ACCOUNT NUMBER
Open the Tuya Smart APP, sign up for a new account or log in with an existing account.
PRODUCT FUNCTIONS DIAGRAM
- Tum on the LED strip and enter the home of APP while ensure Bluetooth on and the WIFI signal is good and stable.
- LED strip will flashing when turn on the power supply. Stay at the home page and found the push notification, then click Go to add.
- Select the Wi-Fi connected to the smart device, input the Wi-Fi password, and then click “Next” to wait for the matching to succeed. {Make sure smart devices share the same Wi-Fi)
DEVICE PAIRING-AUTO SCAN
- Turn on the LED strip and enter the home of APP while ensure Bluetooth on and the WIFI signal is good and stable.
- LED strip will flashing when turn on the power supply. Stay at the home page and enter the APP adding device interiace, click Auto Scan to find the device then click next.
- Select the Wi-Fi connected to the smart device, input the Wi-Fi password, and then click “Confirm” to wait for the matching to succeed. (Make sure smart devices share the same Wi-Fi)
DEVICE PAIRING-BLUETOOTH MANUALLY
- Tum on the LED strip and enter the home of APP while ensure Bluetooth on and the WIFI signal is good and stable.
- LED strip will flashing when turn on the power supply. Stay at the home page and enter the APP adding lighting device interface, click “Lighting(Bluetooth)”.
- If the LED strip is not flashing when turn on the power supply, long press the Reset button for more than 6 seconds. While LED strip flashing, select “confirm the light has flashed”, then click “Next”.
DEVICE PAIRING-AP PAIRING
- Turn on the LED strip and enter the home of APP while ensure Bluetooth on and the WIFI signal is good and stable.
- LED strip will flashing when turn on the power supply. Stay at the home page and enter the APP adding lighting device interiace, click “Lighting{BLE+Wi-Fi)”.
- If the LED strip is not flashing when turn on the power supply, long press the Reset button for more than 6 seconds. While LED strip flashing, select “confirm the light has flashed”, then click “Next”.
- Select the Hotspot connected to the smart device, input the Wi-Fi password, and then click “Next” to wait for the matching to succeed. {Make sure smart devices share the same Wi-Fi)
APP FUNCTION INTRODUCTION
Click the interface to control it according to the specific mode of the
specific LED strip. The following is public function
introduction.
THIRD-PARTY CONTROL
In the Tuya Smart APP: Find more service in “Me” menu, click to enter “voice
service” (Alexa/ Google Assistant) and other services, click on the service
you need. Connect to the third-party service device according to the operation
guide
For any product and APP updating.please contact with customer service.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>