diode led DI-DMX-TW-WMDC-1ZWH Tunable White DMX Wall Mount Zone Controller Installation Guide

diode led DI-DMX-TW-WMDC-1ZWH Tunable White DMX Wall Mount Zone

Controller

SAFETY & WARNINGS

1. Install in accordance with national and local electrical code regulations.
2. This product is intended to be installed and serviced by a qualified, licensed electrician.
3. DO NOT connect directly to high-voltage power. Install with a compatible Class 2 constant voltage LED driver (power supply).
4. Only install compatible 12V and 24VDC constant voltage luminaires.
5. This product is rated for indoor installation and is not protected against moisture.
6. Do not modify the product beyond instructions or the warranty will be void.

QUICK SPECS / MODELS

DI-DMX-WIFI-WMDC-1ZWH

WiFi Transmitting

Distance

| 40 ft.

TOOLS FOR INSTALL

Specification

INSTALLATION

1. TURN THE POWER OFF AT THE CIRCUIT BREAKER
   SHOCK HAZARD! May result in serious injury or death. Turn the power OFF at the circuit breaker prior to installation.

2. DETERMINE THE LOCATION TO INSTALL COMPONENTS
   See SYSTEM DIAGRAM for more information. DMX luminaires can be connected directly to the controller. DMX Decoders are only utilized to control Non-DMX type luminaires.

3. CONNECT COMPONENTS
   Only use copper wiring. Reference WIRING CONNECTIONS and SYSTEM DIAGRAM further in this guide for visuals.
   

4. TURN THE POWER ON AT THE CIRCUIT BREAKER

If the system remains unresponsive or is working improperly, turn OFF main power at the breaker and verify all connections.

INSTALLATION

MOBILE DEVICE OPERATION

The DMX controller can also be controlled remotely via WiFi with a compatible IOS/Android mobile device. Go to iOS or Google Play App Store. Search for “TOUCHDIAL” and download an application.

PAIRING CONTROLLER TO MOBILE DEVICE

1. Go to the WiFi settings of the mobile device.
2. Connect to WiFi Network ‘EasyLighting’.
3. Type in Password ‘0123456789’.
4. Open the TOUCHDIAL™ Application.

WIRING CONNECTIONS

• DO NOT connect directly to 120VAC.
• See ‘System Diagram’ for a general system design.

MOUNTING

SETTING DMX ADDRESS

Each DMX decoder or DMX luminaire needs to be addressed correctly so the controller can communicate with each decoder. To pair a DMX decoder or luminaire to the controller, set each decoder/luminaire to the following address:

• Set to address ‘001’ (will be fixed to address 001 – 002)
  • The controller is fixed with 2 DMX addresses to control the 2 channels:
  • CH1 – Warm White, CH2 – Cool White.
• Once the DMX address is set on the luminaire or DMX decoder, ensure to Press Zone 1, 2, or 3 on the controller to control the desired zone.

Example of DMX Addressing Display

PINOUT CONNECTION GUIDE

The following diagrams/tables indicate the appropriate connections for patching your own CAT5/RJ45 and XLR-3 splice cables. These diagrams are for general reference and may slightly differ between different cable manufacturers.

Pin No. Function

1. Ground
2. Data –
3. Data +

SYSTEM DIAGRAM

The following diagram is provided as an example of system design. CAT5 (RJ45 connections) data cables are the most cost-effective solution for transmitting DMX-512 signals. XLR-3 cables may also be installed but require an additional adapter for connecting to DMX decoders. Always review each component installation guide for detailed and up-to-date wiring instructions. Install in accordance with NEC and local regulations.

TROUBLESHOOTING

For thorough troubleshooting of LED strip light and luminaires, see LED luminaire installation guides. LED luminaires not responding to touch

1. Ensure the blue indicator light is on by pressing ‘Power.’ A red indicator signifies the device is off. The blue indicator light will blink rapidly when pressing/holding any key on the touchpad.
2. Ensure the DMX decoder/luminaire is addressed properly. For example, address ‘001’ will respond to zone 1 of the controller. See ‘Setting the DMX Address’ for additional addressing information.

LED luminaire responding incorrectly
Ensure all wiring connections are correct. Reversing the Data + and Data – will cause lights to flicker and not respond to the controller.

1. Check power connections of all components (drivers, DMX decoders/luminaires, DMX controller).
2. Check DMX Data connections – See Pinout Connection Guide and System Diagram for RJ45 hard-wiring connections.
3. Check DMX decoder connections – See System Diagram for CH 1-4 connections.

ADDITIONAL RESOURCES

• Visit the online product page at www.DiodeLED.com for additional product specifications & warranty information.
• TUNABLE WHITE DMX512 CONTROLLER SPECIFICATION SHEET
  • For full specifications.
• VOLTAGE DROP CHARTS
  • Use to specify the appropriate wire gauge for installation. Available at the ‘Resources’ page at www.DiodeLED.com.
• ® Toll-Free: 877.817.6028
• Fax: 415.592.1596
• www.DiodeLED.com
• info@DiodeLED.com
• © 2021 Elemental LED Inc. All rights reserved. Specifications are subject to change without notice.

Documents / Resources

| diode led DI-DMX-TW-WMDC-1ZWH Tunable White DMX Wall Mount Zone Controller [pdf] Installation Guide
DI-DMX-TW-WMDC-1ZWH Tunable White DMX Wall Mount Zone Controller, DI-DMX-TW- WMDC-1ZWH, Tunable White DMX Wall Mount Zone Controller, Wall Mount Zone Controller, Mount Zone Controller, Zone Controller, Controller
---|---

References

• Illuminate Your Space - LED Lighting Solutions | Diode LED

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>