Shenzhen Qi Quick Technology QTU201 15W Wireless Charging Holder User Guide
- June 6, 2024
- Shenzhen Qi Quick Technology
Table of Contents
Shenzhen Qi Quick Technology QTU201 15W Wireless Charging Holder User Guide
Product Introduction
The wireless car charger with air purification is a wireless charging product with air purification for the car. Intelligent identification control, intelligent induction, touch control contraction, 2.5D toughened glass surface, TYPE C interface for power supply. It can be used through one-handed operation. Charging can be started only by placing the mobile phone with wireless charging function on the product surface. The air purification system in the product will work immediately after power on. The air is sucked into the product by the exhaust fan, and flows out through ultraviolet disinfection and purification.
Product parameters
- Product name: Wireless car charger with air purification
- Product model: QTU201
- Input parameters: 12V/1.5A QC3.0 supporting car charger
- Output parameter: 15WMAX Sensing
- distance: ‘6mm Ultraviolet air purification wave band 185nm and 254nm
- Operating temperature: -10°C to 40°C
- Product dimensions: 120.5mm`74.5mm*43.4mm
Instructions For use
-
Use the retaining clip of the wireless car charger with air purification to fix it on the air outlet, insert 12V/1.5A or QC3.0 supporting car charger into the cigarette lighter port or power port of the car, insert the standard charging cable USB-A into the USB port of the car charger, and connect it to the wireless car charger with air purification through the TYPE-C interface. After power on, the air purification function will start to work, and the clamp arms on both sides of the car charger will automatically open, so as to start normal use.
-
Put the wireless charging mobile phone into the holder, the clamp arms will clamp it automatically after coil induction, and the mobile phone will start charging
-
During charging, keep the mobile phone close to the surface of the wireless car charger for better charging effects.
-
To remove the mobile phone, just touch the side touch switch, or lightly press the mechanical switch, the clamp arm will be automatically opened to remove the mobile phone, but the air purification function will continue to work. The air purification function will stop when the wireless car charger has no power.
Precautions
- The standard high-power car charger power cord and the mobile phone with wireless charging power supporting QI standard shall be used.
- The recommended width of the mobile phone is 68 to 85mm. The actual maximum opening and closing width may vary depending on the manufacturing process and measurement method. Please refer to the actual use.
- If the mobile phone is equipped with a case, be careful not to use a case with metal back, and the thickness of the case shall not exceed 3mm.
- For mobile phones that do not support wireless charging, the car charger holding function can also be used for wired charging.
- The surface of the attached holder shall be clean and flat. Due to strong adhesiveness of the backing, forcible removing after firmly adhered may damage the interior. It is recommended to contact a professional organization for handling.
- Type-C port only supports car chargers with QC3.0 standard fast charging protocol.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Customer Support
Phone: 0769 81031929
Web:www.ququick.com.cn
www.hiqiling.comcu