Shantou Zingo Hobby 904 Remote Control Car Series Instruction Manual
- June 6, 2024
- Shantou Zingo Hobby
Table of Contents
Shantou Zingo Hobby 904 Remote Control Car Series
Vehicle lnstuction Manual
BATTERY INSTALLATION
IMPORTANT uses a 9.6V Rechargeable Battery Pack and the Battery Pack is Please
charged note by a the USB vehicle cable
BATTERY LOADING
Please charge the rechargeable battery for 4 hours prior to use
(WARNING: Never over than 6 hours – overcharging will cause permanent
damage to the battery.
- Plug battery.) the USB cable into socket (See Diagram #1)
- the battery pack with the USB cable. Make sure the battery pack is secure with USB Connect cable.
- You should charge the battery pack for 6 hours the first two times .Then subsequent
- charges will only 4 require hours, 4 the hours. battery will be warm. This condition is normal for fully After charged charging batteries. for
- lf the speed of the car slows down suddenly, it is time to recharge.
- After use, the battery Recharging pack a will warm be or hot hot !Wait battery at least pack 20 will minutes greatly until shorten it cools the use before life of the recharging. battery.
- The vehicle must be used with the recommended transmitter .
- The transmitter is not a toy.
BATTERY PACK CARE
- If battery pack and connector are wet, thoroughly dry before charging .
- We recommend unplugging the battery pack if battery pack will not be used for several days.
ATTENTIONS PARENTS
examined for potential It is hazards and recommended that any that this
potentially toy and all hazardous accessories parts be to be repaired or
periodically replaced.
HOW TO INSTALL BATTERY IN VEHICLE
- Turn TO over the INSTALL vehicle BATTERY and push IN the VEHICLE ON/OFF to “OFF position .(See Diagram #2)
- lnsert the 9.6V battery pack into battery compartment.
- Replace the battery cover
HOW TO PLAY
START TO PLAY
- push theON/OFF switch to the “ON” position of the vehicle (See Diagram6)
- Push the ON/OFF switch to the “ON” position of the transmitter FORWARD & REVERSE RUNNING
- forward and reverse, pull or push the trigger in the transmitter respectively. To (See make Diagram the car 7\8) FRONT WHEELS STEERING ADJUSTMENT
- adjust the lever for satisfactory alignment on the If the underside vehicle of the does vehicle not run (See straight Diagram forward, #9)
- If the vehicle runs towards left, turn “Steering Alignment Lever” towards “R”.
- If the vehicle runs towards right, turn “Steering Alignment Lever” towards “L” STEERING OPERATION
- Turn trigger backward at the same time, the the car steering will turn wheel right or forward left or and run backward forward. while (See pulling Diagram the 10)
- Turn trigger forward at the same time, the the car steering will turn wheel left or forward right or and backward reverse. while (See pushing Diagram the 11)
Battery Caution
- For maximum performance, use alkaline batteries.
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
- Do not recharge non-rechargeable battery.
- Ensure the batteries are inserted with the correct polarity.
- Remove batteries when vehicle is not in use.
- Rechargeable batteries should only be charged under adult supervision .
- Remove rechargeable batteries from toy before charging.
- The supply terminals are not to be short-circuited.
- The antenna are not inserted into socket outlet.
NOT SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE DUE TO SMALL PARTS
- (Diagram #1) < > 9.6V battery pack > < 3 USB cable ry pack and battery
- (Diagram #2) < < 5 4 > > On/Off Connect switch battery < 6 > Battery Cover the battery compartment < < 7 8 > > 9.6V Unscrew battery to open pack
- (Diagram #3)< <1 9 O> > AA Battery 1.sv•2 Panel of battery(excluded) transmitter
- (Diagram #4)<11> <12> On/Off Transmitter switchLED light
- (Diagram (Diagram #5) <13> LED LIGHT
- (Diagram #7) #6) <14> On
- (Diagram #8) rd <18><19> BackwaReverse alignment lever
- (Diagram #9) <20> Steering Wheel
- (Diagram #10) <21> Steering Steering Wheel
- (Diagram (Diagram #11) #12) <22> <23> Stop
FCC ID 2ASGE9O4
This device comp I ies with Part 15 of the FCC Ru le e s.
- this ration is device subject may not to the cause fo l loharmfu wing I two interference. conditions: and
- including this device interference must accethat pt any may cause interference undesired received, operation.
“Hereby, comp I iance SHANTOU with the ZINGO essHOBBY ential CO. , LTD, requirements dec l ares and that other rethis l evant Remote provisions contro l car of Diserectries ive is in 1999/5/EC. Manufacture Name: SHANTOU ZINGO HOBBY CO .. Manufacture Address: Fengx in lndustr i a I Zone. LTD Fengx i ang Street. Chengha i Di stri ct, Shantou, Guangdong, China
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or
relocate the receiving antenna. Increase the separation between the equipment
and receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/ TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>