Guangdong Wealwell Technology YF658G Bidet Toilet Seat User Manual

Guangdong Wealwell Technology YF658G Bidet Toilet Seat

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

DANGER – To reduce the risk of electrocution:

1. Do not pour water or detergent on the power plug. It may cause fire, electric shock and other accidents.
2. Do not bring lit cigarettes or burning species close to the product. It may cause a fire.
3.  Please do not continue to use the product when the product fails. Please contact the after-sales service staff for maintenance. When the following situation occurs, please remove the power plug and close the inlet angle valve.
4. If the product is still used in the event of a malfunction, it may cause problems such as fire, electric shock, water inflow in the room. (The normal life of this product is six years, continued use beyond the service life may lead to accidents.)
5.  This product belongs to the electrical products, do not put it in places where there is water or places of high humidity. When used in the bathroom, please install a ventilation fan or ventilation port to keep the bathroom in good air circulation. Otherwise, it may cause a fire or electric shock.  If the power cord is damaged, do not disassemble it yourself and must be replaced by the manufacturer or its service department or relative department.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons.

1. It is absolutely forbidden to disassemble, repair and transform this product by yourself. It may cause fire, electric shock and other accidents.
2. Only tap water can be used. Otherwise may cause infectious dermatitis and other diseases.
3.  Forbiddance sitting on the seat for a long time, the seat temperature should be adjusted in low-grade, please note that low-temperature burns. The following personnel should set the seat temperature at low-grade when using the toilet.
4. Do not forcibly stretch the connecting pipe of the water supply pipe. Otherwise it may cause water leakage.
5. Defecation clean function, a special cleaning function, only allowed to use one time whenever you use the toilet, non-repeated use!
6. Do not rely on the seat cover or forcibly press the control panel. Otherwise it may result in malfunction or breakage. Forced application of force may cause seat cover and control panel damage, resulting in personal injury
7. Do not place containers containing liquid such as vials, cups, cosmetics, pharmaceuticals, etc. or small metal objects on top of the product. Inadvertent entry into the product may result in fire or electric shock.
8. Do not place the product in direct sunlight, otherwise the appearance of products may be aging deformation.
9. People with disabilities, mental retardation, etc. (including children) need to use this toilet under supervision, do not let children play with this toilet.
10. Do not use the toilet to flush expect shit, urinate and toilet paper, or it may cause toilet jam, sewage overflow.
11. Please do not hit the ceramic to prevent damages that result in leakage
12. Please do not use in the environment below 3℃.
13. When installing the inlet angle valve, please tighten firmly. Otherwise, it will lead to water leakage
14. Prevent damage caused by freezing. Freezing can cause damage to the water hose and product interiors and cause water leakage.
15. When traveling for long periods of time or when not in use, please unplug the power plug from the outlet.
16. This product is only for bathroom, and should not be used for any purposes other than the ones described in this manual. Otherwise maybe cause to fire, electric shock, personal injury or malfunction.
17. Do not allow urine and other contaminants to touch the smart toilet. Doing so may cause odor or cause malfunction.
18. Do not forcibly close the seat and seat cover. It is necessary to avoid the collision of the seat lid and the seat cover when turning them. Otherwise maybe cause malfunction.

DANGER – Improper use of the grounding plug can result in a risk of electric shock.

1. Do not use loose power outlet. It may cause a fire or electric shock.
2. Please use the power outlet within the specified conditions (110-120V~, 13A, 60Hz socket). Do only use 110-120V~ power supply. Using power beyond the socket regulations may cause the socket to heat up and cause a fire.
3.  Do not damage the power cord and seat wire.
4. Do not damage, do not process, do not heat;
5.  Do not force bending, do not curly tied, do not pull;
6. Do not put heavy objects on the power cord and the seat lid connection, ignoring product damage and continuing to use may result in fire, electric shorts and other conditions.
7. Please check if grounding is done. A product that is not grounded may cause an electric shock in the event of a malfunction or leakage.
8. Unplug the power plug when lightning occurs
9. For external maintenance, unplug the power plug from the socket for safety reasons. Otherwise maybe get an electric shock.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject
to the following two conditions:

1. This device may not cause interference.
2.  This device must accept any interference, including interference that may cause undesired operation of the device

Product functions

Heated Seat, Soft Night Light, Energy Saving, Deodorization, Warm Air Drying, Rear Wash, Front Wash, Defecation Wash, Menstrual, Cold & hot SPA, Children Wash, Nozzle Self-clean, One Touch, Adjustable Water Temperature, Adjustable Seat Temperature, Adjustable Air Temperature, Adjustable Water Pressure.

Using guide

Please follow up the process below before product operation.

1.  Turn on the valve.
2.  Plug the power cord into electrical inlet.
3.  If power button indicator lights, the bidet seat is good to use.

Standby Model
By pressing the power button on the control panel.

1.  Short touch: stop washing or drying model.
2.  Long press: start or stop standby model when it’s in off seat model.

Rear Wash
Touch rear wash button when you are in seat, and start the washing process.

Front Wash
Touch Front wash button when you are in seat, and start the washing process.

Warm Air Drying
Touch air drying button when you are in seat, and start the washing process. It’s off in 4 minutes.

Packing list

Product size

Technical data

Warm water

temperature

| Four grades (Room temperature to 40℃)

Spray volume

| Buttock

cleaning

| About 0.5 to 0.8L/min
Women-only| About 0.5 to 0.8L/min
Warm water heater| 1100W
Safety applause| Temperature sensor, temperature fuse, temperature jumper, flowmeter
Drying device| Wind speed| ＞4m/s
Air temperature| Four grades (Room temperature to 40℃)
Drying heater| 250W
Safety devices| Double-sheet-metal switch, temperature fuse
Deodorizing device| Deodorant| Activated carbon
Power consumption| 1.5W
Thermal| Seat temperature| Four grades (Room temperature to 40℃)
Seat heater| 28W
Safety devices| Temperature sensor, temperature fuse
Switch structure| Seat and cover with damping slow down device

Rated power : at room temperature 20±5℃,inlet water static pressure is 0.18+0.02Mpa. The average power of turning on the cleaning function and working steadily for one cleaning cycle at the inlet temperature of 15±1℃.

Remote control user manual

Remote control code matching steps:
Power off the bidet. Put a wet towel on the bidet sensor label area to pretend someone is sitting on the bidet or put hand on the bidet. Press and hold the STOP/POWER and AIR TEMP. Buttons simultaneously for about 2 seconds, until the 5 indicator lights are turned on and flashing. Turn on the bidet.
When all the 5 indicators turned on, the remote control is connected successfully. Then you can press any button to start using it. If the connection is not successful, try again after about 30 seconds.

Main function

Rear Wash
Short press: start wash buttocks. Long press: start / stop mobile wash.

Front Wash
Short press: start female wash. Long press: start / stop mobile wash.

Warm Air Drying
Short press: start warm air drying.

Stop Current Work
Short press: quit current wash or drying. Long press: turn the toilet power on or off.

Parameter adjustment

Adjust water pressure
Short press “+”, water pressure grade +1, short press”-”, water pressure grade -1. Adjust tube front and rear position. Short press “∧”, tube position grade +1, short press “∨”, tube position grade -1.

Adjust seat temperature
Short press: cyclically adjust seat temperature.

Adjust water temperature Short press: cyclically adjust water temperature.

Adjust air temperature Short press: cyclically adjust air drying

Auxiliary functions

One-touch completes rear wash and warm air drying.

Short press: start automatic “One Touch” mode.

Defecation clean : clean water column shoots into the end of the anorectal to help defecation.

Short press: start defecation clean.

Children: customized the appropriate parameters for children, wash the buttocks. Short press: start children care cleaning.

Cold & Hot SPA: water alternately massages and washes.

Short press : start cold & hot massage. Press continuously: turn mobile cleaning on or off. Night light during night

Short press: turn night light on or off. Press continuously: enter or exit energy saving mode.

Nozzle cleaning: when not seated, stick out the nozzle for daily cleaning.

Short press: start nozzle cleaning.

Others
Energy saving
After the user leaves the seat, intelligently adjust the heating power of the seat.

Remote control installation steps

Product installation methods

Precautions before installing the toilet

1.  This product uses the 110-120V~ voltage, electrical construction requires the commission of professional electrical companies.
2.  When using this product, tap water pressure must be 0.08Mpa – 0.75Mpa.
3.  After the installation, plug the product power into the socket. When you hear a “D”, it means that the product is p1. Precautions before installing the toiletowered on and the self-test is completed.
4.  Please use the water supply pipe attached to the toilet for installation. Do not use the old water supply pipe, otherwise it may affect the performance of the product.
5.  Please do not use cloth cover or cushion on the seat, otherwise it may cause seat induction not good.
6.  In low-temperature environment, please leave the product in a warm room for 2 hours before installation to prevent internal moisture from damaging the machine.
7.  The following picture shows the toilet standard specifications of the product that can be installed.

Dimensions of the toilet that can be installed

The method of separating the installed toilet seat and fixed water purification filter.

1.  Turn the hose valve (supply stop) to the right and lock it, and then separate the water tank from the water pipe valve (supply stop) with the water supply pipe.Please use the supply hose included. Do not use the old one.
2.  Detach the installed toilet seat. (Disassemble the product according to the original method of toilet seat.

Take proper care of seat cover, bolt, nut seal. They will be needed when moving or reinstalling.

Connect the T valve to the water pipe valve (supply stop), and then separately connect the water tank and the seat water supply pipe to the assembled T valve.

Fixing method of fixed plate and intelligent toilet

1. Insert expansion nut into toilet seat holder. Place mounting plate on toilet seat. Stainless steel screws are threaded in turn Square gasket, moving fixed plate, fixed on the installation plate fixed plate, the installation plate fixed plate fastening on the toilet.
   

2.  Insert the mounting plate assembly into the center of the rear of the smart toilet seat cover. If there is “click” sound, it is in normal installation state.
   Do not flip the toilet during operation.

3.  Sway the smart toilet seat cover back and forth, and left and right to check whether it will come off.
   

Smart toilet disassembly method
Press the removal button on the side of the smart toilet and pull the product forward in this state, then the toilet is separated from the seat.

Instruction for testing after installation
After the installation is complete, it must be commissioned and record the results of the installation points in the following form.

Is it connected to the 110-120V~, 13A, 60Hz power outlet? Grounding the equipment is required.|
Is the power outlet loose?|
Is the water supply opened?|
Tighten the various joints (such as the filter, water supply pipes and screw, etc) ?|
Is the indicator light on?|
The spraying nozzle is leaking? After wiping the nozzle, check if there is any water leakage.|
The various functions of the product is normal:

Rear wash and front wash, water temperature and seat temperature adjustment, cold & hot SPA, soft lighting and nozzle cleaning, etc. Are they normal use? The above series of actions should be checked.

|
Date of installation|  | Name of the installation store|  | Installer|

Product cleaning and maintenance methods

Warning: waterproof toilet cleaning precautions

• Do not clean the product with your hands in case of damage or failure, to avoid secondary failure.
• Do not use hydrochloric acid detergent, thinner, bleach, benzene or strong detergent to clean the surface of the toilet. Do not allow pesticides, air fresheners and deodorants to stick to the toilet bowl.
• The body discoloration, cracking and damage caused by the use of the above-mentioned reagents, even within the warranty period also need to paid the services.

Nozzle cleaning

1. On the machine power mode, do not sit on the seat.
2.  Press “Nozzle cleaning”, entering the manual cleaning nozzle mode. (Can not activate “nozzle cleaning” mode when seated)
3.  Please use soft brush or soft cloth when cleaning.
4.  After the cleaning is completed, press the stop button or in the seatingstate, the cleaning tube is automatically retracted.

Warning : do not force out or push into the cleaning tube during cleaning, or it may lead to machine failure.

Toilet appearance cleaning method Clean the toilet when the toilet is in fixed state.

1.  Please use sponge or soft cloth stained with neutral detergent to clean the surface of the toilet.
2.  Please use a soft cloth to clean the nozzle cover and dry nozzle cover. Be careful not to damage the rubber seal.
3. Spray water on the toilet and clean it.
4.  After cleaning, clean the whole cotton cloth.

Do not use strong detergent containing hydrochloric acid. Do not use deodorant. Refer to cleaning precautions.

How to clean the gap between smart cover and ceramic toilet.

1.  Press the disassemble button below the right side of the toilet to detach it.
2.  Clean the nozzle cover and the drying nozzle cover under the toilet bowl with a soft cloth or and clean the lower part of the toilet bowl and the ceramic seat toilet with a tool for cleaning.
3.  After cleaning, clean the whole a cotton cloth and install the toilet.

Seat toilet management methods in winter
In order to prevent freezing in winter, please follow the following methods to manage.

1.  Check whether the power plug is properly inserted into the socket.
2.  When the bathroom has no heating device, please use cloth to wrap connecting pipes or other insulating materials for insulation.
3.  When the toilet will not be used for a long time in winter, please unplug the power plug and discharge the water inside the body.

Note :
Please tighten the filter firmly, otherwise it may cause water leakage. Do not grab the filter net too strongly as it may distort or rupture.b When blockage blocks the filter, the pressure of the flushing water may not be enough, so please change the filter regularly. The filter is usually replaced every six months. If you do not regularly change the filter, the buyer shall be responsible for the consequences of the malfunction. Please clean the toilet filter regularly once in three months. We recommend that you do not use detergent when cleaning. Clean it directly with tap water.

How to deal with common problems

Functions does not work at all.

| The seat sensing area uses cloth cover, mat and other items.| Please remove the cloth cover, mat and other items.
Power is cut.| Please wait for power recovery.
Socket is loose or poor contact.| Plug in, ensure good power supply.
Whether the power reset button is pressed.| Please press the power button on the toilet.
Flushing| ****

Water doesn’t come out.

| No water.| Please wait for the water supply to resume.
Water inlet valve is clogged with dirt.| Open the inlet valve.
Filter is clogged with dirt.| Please change or clean the filter.
Whether the water supply tube is bent and clogged.| Eliminate the water supply pipe bending.

Flushing power is not strong enough.

| Water pressure is set at low-grade.| Please adjust the water potential power by “button description” on the remote control.
Filter is clogged with dirt.| Please change or clean the filter.
Clean the nozzle to see if there is any blockage.| Please clean the nozzle.
Water temperature is not high enough.| Whether the water temperature is set at low or normal temperature.| Please reset the water temperature by “button description” on the remote control.
No water supply when flushing.| Press the”Rear Wash”or”Front Wash”key for about 60s, the machine will automatically stop.| Please click “Rear Wash” or “Front Wash” key again.
Toilet Seat| ****

The heated seat is not heating.

| Thermal seat’s heating strength is set in the low or off state.| Please reset the seat temperature by “button description” on the remote control.
The toilet is set in the energy-saving state.| Please press the power button to exit energy-saving state.
Whether the power outage.| Please wait for power recovery.

Thank you for choosing us
The company is committed to product development and improvement. If there is any difference between the original manual and the improved one, please read the corresponding version of the manual. We apologize for any inconvenience.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>