timeTec TT-W033C-NL Smart Indoor Siren User Guide
- June 6, 2024
- timeTec
Table of Contents
timeTec TT-W033C-NL Smart Indoor Siren
INTRODUCTION
A wireless TimeTec Siren is a device that sends warning signals to people in
the form of sound and light whenever danger is detected. It is equipped with a
bright LED luminous tube and a super buzzer, which can deliver a stronger
warning effect. When the front-end sensors detect abnormal situ-ations such as
intrusion, fire, emergency, etc. The sound and the light siren will emit a
high-decibel alarm warning light after the sound and light siren is connected.
This will deter intruders and remind users.
INSTALLATION METHOD
Plug into three-hole socket
INSTRUCTIONS
ADD A DEVICE
Please use with TimeTec Gateway Camera.
Added by QR code scanning:
- Download and log onto the i-TimeTec APP on your mobile phone. Click “+” on the Smart Home page to enter the scanning interface;
- Scan the QR code on the TimeTec Siren cover to add the wireless Siren to the TimeTec Gateway device according to the prompt (requires network connec-tion)
Added by manual input:
- Download and log onto the i-TimeTec App on your mobile phone. Click “+” on the Smart Home page to enter the scanning interface, and then click the [Enter] button to enter manually the serial number of the front device below the QR code of the wireless TimeTec Siren.
CHECK THE NETWORK ACCESS
Network access check:
After adding the TimeTec Siren device, check if the replaceable plug is
fastened. Power on the TimeTec Siren, and it will automatically register for
network access (Click the TimeTec Gateway Camera device interface [Settings]>
[Devices]>
[Device List] to ensure the corresponding icon is turned Gray as an indication
of network connection);
Exit network check
After pressing the exit-network alarm button on the side of the TimeTec Siren,
the strobe light will flash once to indicate that the network has been
success-fully disconnected.
ALARM ARMED AND CANCELLATION
Please use with i-TimeTec probes (such as wireless TimeTec Door/Window
Magnetic Sensors, Wireless TimeTec PIR/Motion Sensor, Wireless TimeTec Panic
Button, Water Leaking Sensors, Smoke sensors, etc.). Add any required probes
to the same TimeTec Smart Gateway device.
- Alarm arming: Once the TimeTec Siren is connected to the network and the probe sensor is triggered, the TimeTec Siren alarm will be activated while pushing the alarm information to the i-TimeTec App server. (If the probe type is: i-TimeTec motion sensor, wireless door/window magnetic sensor, wire-less smoke sensor and etc., you need to set the arming state on the Gateway device interface of the i-TimeTec App before you can trigger TimeTec Siren alarm);
- Alarm cancellation: The Smart Gateway device interface of the i-TimeTec APP is set to disarm and to cancel the alarm. If other probe sensors are using a spe-cial alarm cancellation method, please refer to the alarm cancellation method in its product manual.
Q&A AND TECHNICAL TIPS
-
Q1: TimeTec Siren does not respond when the probe sensor alarm is triggered.
A : TimeTec Siren is not connected properly to the network. Add the device again in the i-TimeTec App. -
The device should be installed in a dry place without chemical corrosion.
-
It is strictly forbidden to install under the power-on state during the installation. The installation place of Smart Siren should be far away from magnetic interfer-ence.
-
This product can reduce the occurrence of accidents, but there is no foolproof guarantee. For safety caution and to use this product correctly, it is recommend-ed that you stay vigilant and strengthen the awareness of safety precautions practice.
-
Do not frequently disassemble the device, or repair and/or replace its original components, this can cause serious damage to the product. Any questions or help required, please contact our support centre at support@timeteccloud.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>