VIGILATE VIGIPTZ Wireless Pan-Tilt Camera User Guide
- June 6, 2024
- VIGILATE
Table of Contents
VIGILATE VIGIPTZ Wireless Pan-Tilt Camera
Features
Designed for use with VIGILATE Smart alarm systems, the VIGIPTZ Indoor Camera
is a wireless Internet based camera that provides outstanding performance.
This IP camera is easy to configure and operate via the VIGILATE Control App.
It uses Access Point technology to help the camera connect to wireless routers
fastandeasily. By ultising global oversea servers, users can easily watch the
live video or recorded videos on their phone from anywhere anytime.
Video Resolution 1920×1080@30FPS, Auto IR-LED illumination with auto IR-Cut
Switch, 8 IR LEDs, IR Night vision range(30 meters), Wi-Fi compliant with IEEE
802.11b/g/n, 2.4GHz band Support, WEP,WPA-PSK and WPA2-PSK Encryption, Support
recording and playback via micro SD Card, up to 128GB. Compatible with ONVIF
Protocol H.265 main profile video compression format.
Parameters
Setting Up Camera
Power up
Connect the power cable into power connector of the camera, and plug the power
adapter into an outlet.
Note: Please DO NOT use an Ethernet cable to connect the Smart Camerato
LAN before camera setup process is done.
Pairing with system
Tap“+” Add accessory to scan QR codes printed on the camera, you willbe guided
to connect to Camera by connecting the AP’s name which started with IPcam***.
WiFi Settings
- After switching back to the App, you will have the page to set up the Wi-Fi of the camera.
- Select your WiFi router in the list, then input Passwordand Save.
- The camera will start to connect to the router, you will hear the camera play a special tonethat means it was connected tothe router successfully.
- Name it and set the password, then start to use the camera.
Access live video and daily operation
- Go to Camera list from the App, select the camera you would like to access.
- Press the play button on the snapshot of the camera to access live video.
Quick Actions for camera
Use below buttons to take a snapshot, listen and talk
: Change the camera view angle by this button
: Snapshot and save pictures to album.
: Hearing the audio from the camera.
: Talking to the camera
Accessory Setting
Tap camera name to enter Accessory Setting to rename,delete, re-configure camera network and settings.
Camera Settings
Tap “Camera Settings” to re-configure the camera and check more detailed information.
SYNC with phone’s timezone:
SYNC with phone’s timezone.
Horizontal & Vertical Flip:
Flip the screen to view correctly if the Smart Camera was been installed
upside-down.
Wi-FiSetting:
When the camera is online, in the event of a network change, tap ”Wi-Fi
Setting”, and select the new Wi-Fi from the list.
Motion Detection & Recording
Tap “Motion Detection & Recording” to enter Motion Detection & Recording setting page. Users can choose to enable or disable it; setting alarm sound, motion sensitivity and alarm time.
FAQ
I’ve Already Connected My Camera to Internet, But I Can’t Connect It in
the App.
Make sure you used the right QR code during the pairing section.
Make sure you are using the 2.4GHz Wi-Fi, the camera can’t support 5GHz yet.
The camera supports IPV4 only. DHCP Server/Services should be enabled on the
router setting.
If you are using a firewall, all ports from 10000 to 65635 of your cameras IP
address should be allowed for in/out in the firewall rule to allow data from
the camera.
I Can’t Save the Snapshots.
The App will need access to your phone’s album to save the snapshots. The
authorisation might need to be approved while using the function for the first
time in some phones.
If you click the ‘No’ option during the authorisation, you might need to
enable it in the system setting menu.
How to Reset My Camera Network?
If you relocate the camera, launch the APP and tap “NetworkSetting” on the
“Accessory Setting” page. Press and hold the reset button on the back of the
camera for 3s after the camera is powered on, it’ll makea tone and enter AP
mode.
How to Reset My Camera?
PLEASE MAKE SURE YOU CLEARLY UNDERSTAND THE RESULT OF RESETTING:
ALL DATA WILL BE ERASED INCLUDING THE INTERNET SETTINGS.
Press and hold the reset button on the back of the camera for 10s after the
camera is powered on. After successfully resetting, it will make a tone which
means the reset is done and the camera enters AP mode.
Installation Guide
Note: Prior to installation ensure that the installation environment can support at least 3 times the weight of the camera. And do not place objects on top of the camera.
- Drill pilot holes in the position that you wish the camera to be seated using a 3/16 drill bit.
- Screw the mount on the wall with two screws provided.
- Loosen the thumb screws to adjust the mount to the desired position.
- Once the position is set, tighten the screws securely
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>