MARLEY EM-JT002-SB Stir It Up Semi-Automatic Two-Speed Turntable User Guide

: June 5, 2024
: MARLEY

Table of Contents

MARLEY EM-JT002-SB Stir It Up Semi-Automatic Two-Speed Turntable
PRODUCT MAP
FUNCTION LAYOUT
SETUP
BLUETOOTH® PAIRING
NON-BLUETOOTH® CONNECTION SETUP
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MARLEY EM-JT002-SB Stir It Up Semi-Automatic Two-Speed Turntable

PRODUCT MAP

LEGEND

Spindle
Turntable
45 Adaptor
Balance Weight
Anti-Skating Knob
Tone Arm Lift Level
Tone Arm Rest Holder
Tone Arm
Stylus
Needle Cover
Off/33/45 Knob
Power Adaptor With 4 Interchangeable Plugs

FUNCTION LAYOUT

LEGEND

RCA Line Out
Pre-Amp Switch Button
USB to PC Recording
Off/33/45 Knob
Bluetooth® Button
– VOL + Knob
Headphone Jack
Anti-skating Knob

SETUP

POWERING ON YOUR STIR IT UP WIRELESS

Your Stir It Up Wireless uses an AC power supply and is powered by a standard wall outlet.
Connect the power adaptor to the wall outlet.

ATTACHING THE DRIVE BELT
Note:
The drive belt is stored underneath the aluminum platter. Look on the under side of the platter, it will be the black elastic band stored around the center.

To fit the belt, lift the belt over one of the larger holes in the platter and hook it around your finger.
Keeping the belt looped around your finger, place the platter on the turntable base.
Line up the large hole with the gold-colored spindle and gently loop the belt around it. The belt should now be around the base of the platter and the gold spindle. The platter should be attached to the base.
Now place the REGRIND™ silicone slip mat on the turntable.

BLUETOOTH® PAIRING

Power on the external Bluetooth® device first before turning on the BT function on the Turntable.
Press the BT button on the turntable to turn on the Bluetooth® transmitter.
Press button again to enable the unit to search the Bluetooth® device till BT indicator light becomes solid. This will indicated your devices are paired.

NOTE:
If the Turntable does not pair with your Bluetooth® device within 30 seconds, press the Bluetooth® search button again on the turntable and it should pair.

Blue LED light flash
Blue LED light stable

DISCONNECT BLUETOOTH® PAIRING
Long press and hold the BT button till the BT indicator light turns off. Turntable will then disconnect from an external device.

PLAYING A RECORD

Put a vinyl record on the turntable.
Assemble the balance weight and set it to a proper position.
To adjust the balance weight rotate the balance weight at counter-clockwise.
Lift and move the tone arm to turntable. Place the tone arm on the edge of the record.
Turn the RPM Dial knob to select the speed according to the record you are playing.
The turntable platter will auto stop when the music has ended. Lift the tone arm and place it to tone arm rest manually.

To listen to side B, flip record and repeat the above steps. 33 RPM speed to play corresponding size 33 vinyl disc 45 RPM speed to play corresponding size 45 vinyl disc To power the unit off Rotate the RPM Dial knob to the off position.
Note:
Remove the needle cover before you balance the tone arm. Hold tone arm whenever you make any adjustment or action so as to protect the tone arm. Do not try to adjust the balance weight while playing a record as this could break the needle and scratch the record. Re-secured the tonearm before transportation to protect the needle. Remove the balance weight before transportation to prevent damage or breakage to the unit. Do not stop or turn the platter manually. Moving or jarring the turntable without securing the Tone arm clamp could result in damage to the Tone arm.

ANTI-SKATING
Normally the anti-skating should be set to its minimum setting. Anti-skate compensates for inward tracking forces that occur with certain pick-up when the stylus nears the center of the record. If the turntable is experiencing excessive skipping while nearing the center spindle, try increase the anti- skating in the increments indicated on the dial. Start by adding an increment of 1, test its performance, then increase it more, and so on.
Note:
During adjusting the anti-skating knob, leave the tone arm and balance weight alone to prevent damaging the stylus (needle).

VOLUME CONTROL
Increase Volume: Rotate the Volume Knob clockwise. Decrease Volume: Rotate Volume Knob counterclockwise.

HEADPHONE OPERATION VIA HEADPHONE JACK
Connect a set of headphone (not included) in the headphone jack.

Note:
Never put on the headphone till you have plugged in the headphones plug.

USB TO PC RECORDING
Download Full instructions for the Audacity Software at: http://www.audacityteam.org/download/

Connect the Turntable and the computer via the provided USB cable.
Follow the instruction of the software installation steps and operation interface.

NON-BLUETOOTH® CONNECTION SETUP

CAUTION:
Switch off the power to all equipment before making connections. Read the instructions of each component you intend to use with this unit. Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord.

LINE OUT OPERATION

Switch the PRE-AMP OFF/ON SWITCH to ON position.
Plug one end of the RCA cable (included) into the LINE OUT socket at the back of the unit. Be sure to match the color with the socket.
Plug the other end of the cable into the LINE IN socket of your home amplifier device.
Switch on the unit and the amplifier device you connected.
Adjust the volume on the amplifier device.