JAM KIX BT2107 Bluetooth Speaker User Manual
- June 5, 2024
- JAM KIX
Table of Contents
User Manual
JAMKIX Liquid Sound
Before using this product, please read these instructions carefully. Once you have read these instructions, please keep them for future reference.
Product Diagram
Specifications
| Waterproof Level | IPX7 |
|---|---|
| Version | 5.0 |
| Transmission Range | 10m |
| Output Power | 3W |
| Speaker driver | Comm |
| Impedance | 4 Ohm CO) |
| --- | --- |
| Frequency Response | 100112.20101z |
| Lithium Battery | 3.7% 600mAh |
| Material | ABS+silleonit |
| Dimension | 911`98•311mm |
HOW TO USE
- Before using the Bluetooth speaker for the first time, you must charge it for at least 30 minutes.
- Note: The full charge time is 2 hours. To charge the speaker, connect the Micro USB charger cable (included) to an adapter or a computer. 2. Once the speaker is charged, press and hold the button “Power ON/OFF” for 3 seconds. 3. Once the speaker is turned on, the Bluetooth function will turn on automatically and the speaker will start searching for Bluetooth devices. 4. Turn on your device’s Bluetooth and select the name “JAMKIX Liquid” which will appear on your device and pair it with the speaker.
- Notes: After the device is paired to the speaker, the speaker will beep. Once the speaker is turned on, it will pair with the last device is connected with. If the connection with that device fails, the speaker will go into pairing mode with other devices. 5. Press the “Volume down/ Previous song” button once to decrease the volume of the song, and press it for 3 seconds to go to the previous song. 6. Press the “Volume Up/ Next Song” button once to increase the volume of the song, and press it for 3 seconds to go to the next song. 7. To answer calls while the device is connected to the speaker, press the On/ Off button once. To end the call, press the On/ Off button once again. And to reject a call, press and hold the On I Off button for 4 seconds.
PRECAUTIONS
Read the following recommendations before using the Bluetooth speaker:
- Keep the speaker dry and do not take it to humid places to avoid affecting the internal circuit of the product.
- Keep the speaker away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery, or distort certain plastic parts.
- Do not expose the speaker to an extremely cold area. It may damage the internal circuit board.
- Do not disassemble the speaker as it may be damaged and this voids the warranty
- Do not allow other hard surfaces to fall to the tread. The internal circuit may be damaged
- Do not use harsh chemicals or detergents to clean the product.
- Do not overcharge or keep it plugged in for longer than 2 hours as this will decrease the lifespan of the device
If you have any questions or concerns please contact us at support@jamkix.com or go to our website at JAMKIX.com/help
To register your device go to JAMKIX.com/account/register
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>