ZKTeco UHF 6 Pro Series High-Performance Long-Distance RFID Reader User Guide

ZKTeco UHF 6 Pro Series High-Performance Long-Distance RFID

Reader

Product Summary

UHF 6 Pro series is a new generation of RFID UHF series product of our company’s independent research and development of the long-distance card reader system for parking lots. The product adapts Impinj R2000 card reader chip, and the card reader part adapts module integrated design. It has stable card reading performance, good card reading performance consistency, long service span, minimized external interference, and the product adapts waterproof casing design. The product also fully meets the CE, FCC technology requirements of the product, and has obtained CE, FCC and other security certifications.

Overview

Front View

Lateral View and Interface

Cable Definition

(Active-low)

4| Green| Wiegand D0
5| White| Wiegand D1

NOTE:

1. In “Trigger Read” work mode, the reader will not read cards before a low level signal to “Trigger Point” is delivered. “Trigger Point” is mainly used for working with the ground sensor of vehicle parking system.
2. In “Always Read” work mode, once the card is in the effective range, the reader will output the card number via Wiegand continually.

Technical Parameter

Safety Precautions

1. The reader working voltage ranges from DC9V to DC16V, it is recommended to use a DC12V /3A power supply.
2. Please wire according to the cable definition.

Modifying Setting via Demo

Working Frequency

| UHF 6E Pro: 865MHz ~ 868MHz; UHF 6F Pro: 902MHz ~928MHz

1. USB Connection
2. Software Introduction Our company provides Demo, used to set the working parameters of the reader. Demo interface is as shown below:

The default configuration of the reader is as follows:

Demo Using Instructions

• Connect the USB port of the reader to the USB port of the computer.
• It is recommended to use power adapter with DC12V/3A specifications.
• To play Demo in computer, click“Connect”, on the right side of the middle will show “SuccessfullyConnected”.
• Wiegand Output Time: Sets the time interval between adjacent wiegand data.
• Reader Indicate: Set whether the buzzer rings when the machine is on the electricity and brush the card.
• Work Mode: Set the working mode of the machine, and including always read mode, trigger mode. Under trigger mode, time of reading card can be set when it is triggered once.
• RF Setting: Set the RF parameters of the machine, including power, spectrum. Power range is 10~33dBm.
• Wiegand Format: Set the machine’s wiegand outputformat.
• Wiegand Output Settings: Sets the forward or reverse output of the machine’s Wiegand Data, and start output from the first few bytes.
• Tag Reading Interval: Set the machine to read the card interval. Read card interval is the time when from the card is read within the scope of the card to the card is left out of the scope of the card to read the second time card.

Access Control Panels Connection

Installation

• Please install the directional antenna with lower elevation angle of 60~75 to suit the correct line of sight.

NOTE:

• Please install the reader as shown in the above picture.The reader is facing the direction and the direction of travel of the vehicle is in a straight line.
• The distance between the reading head and the parking barrier is maintained at 50cm or more.
• Avoid installing the reader against to another.
• The position of the tag/card in the vehicle is as follows:
• The reader detection distance may vary depending on rain, snow or wind.
• The Reader should be away from strong magnetic field when working.
• 15.19 “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • this device may not cause harmful interference, and
  • this device must accept any interference received, including interference that may cause undesired operation.”

FCC

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with a minimum distance 20cm between the radiator & body.

ZK Building, Wuhe Road, Gangtou, Bantian, Buji town, Longgang District, Shenzhen China 518129
Tel: +86 755-89602345
Fax: +86 755-89602394
www.zkteco.com

© Copyright 2014. ZKTeco Inc. ZKTeco Logo is a registered trademark of ZKTeco or a related company. All other product and company names mentioned are used for.

References

• ZKTeco | Biometrics and Computer Vision

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>