Fulcrum Products 30019-30A Wireless Remote Control Switch Instruction Manual
- June 5, 2024
- Fulcrum Products
Table of Contents
Wireless Remote Control Switch
Operating Instructions
Battery Installation & Replacement
- Remove the battery cover by depressing the tab on the back of the switch as shown in the diagram.
- Install 2 AAA batteries making certain to match the polarity as shown in the diagram in the battery compartment.
- Do not mix battery types. Use only fresh batteries. Alkaline is recommended.
- Check the switch operation to confirm that batteries are correctly installed.
- Replace the battery cover.
Operating the Lights with the Wireless Remote Control Switch
You can operate the lights in one of two ways: manually or by using a wireless
remote control switch.
Manual Operation
Follow the instructions provided with the light you are operating.
RC System Compatible
Use any combination of up to 20 RC lights or switches to solve your lighting
problems.
Remote Control Switch Operation
- Press the on symbol I once to turn the lights on.
- Press the off symbol 0 once to turn the lights off.
- To dim the lights, press and hold the on symbol I until the desired light level is reached, then release. Please note that some light types cannot be dimmed using the remote switch.
- The Smart DimmerTM will continue to operate at this light level until it is reset.
Group Code/ DIP Switches
Each light and switch comes with 3 DIP switches that enable the user to
operate 2 or more groups of lights without interfering with each other. These
switches come preset from the factory and will not require adjustment unless:
- You are adding lights to the group, or
- You are operating 2 or more groups of lights within 50′ of each other.
Adding Lights to Your Group
- Remove the battery cover.
- Use a pointed object to gently move the DIP switches to match the settings on the switch.
- Check operation by pressing the switch on and oft
- Replace the battery cover.
- Repeat the process with all of the remaining lights in the group.
Adding Switches to Your Group
- follow the instructions above and arrange the 3 DIP switches to match the code of the group to which you are adding lights.
- We do not recommend groups in excess of 20 lights and switches (total combined).
Installing additional Lights
The chief benefit of using 433Mhz radio frequency control is that it works
through most common barriers (walls, clothing, shelving, etc.) and so does not
require line of sight operation as is the case with infrared systems.
Therefore you can choose a switch location that is most convenient for you to
operate the system. You can locate the lights where they are needed most
without concern for the barriers that might exist. This provides the user with
enormous flexibility. Lights can be located in different rooms, different
closets, or even on different floors of the house if desired. We recommend
choosing the desired location for the lights and testing the operation of the
system before commencing the actual installation. Locate the lights where they
are most needed without regard for physical barriers and test them by turning
them on and off several times. You may occasionally experience a slight delay
in one or more lights. This is normal. Although we have made every effort to
synchronize the operation of these lights, external conditions may cause a
slight delay and on rare occasions, the lights may not turn on or off. If this
happens, turn the lights off and then on again. If it happens repeatedly,
there may be external factors that are disrupting the signal and the location
of the light may need to be altered. Once the final location of the lights has
been determined please ! prove the battery cover and follow the steps below to
mount the light.
Please note : For optimal performance, we recommend installing the lights
12″ or more apart from each other.
Battery Saver
Our unique and innovative battery saver feature is designed to help prevent
unintended battery usage by automatically turning your lights off after a
preset amount of time. There are 3 user-selectable settings: OFF, 30, or 60
minutes. Slide the switch to the desired run time. That’s all there is to it!
Mounting Instructions
Determine the location of the lights and switch, as noted above, then remove
the mounting plate from the switch and the battery cover/mounting plate from
the light and follow the steps below to mount them.
Double-sided Tape Mounting: Be certain that the intended mounting surface
is clean, dry, and suitable for attachment. Take care to select a location
that will not be damaged by the adhesive tape. Remove the protective film and
apply the tape to the mounting bracket. Peel off the protective film and press
the mounting bracket firmly to the intended surface.
Screw Mounting — Wood Surfaces: Drill an 1116″ pilot hole, insert the
screw and gently tighten it until the mounting plate is secure. Do not
overtighten.
Screw Mounting — Drywall: Drill a 3/16″ pilot hole, insert the drywall
anchor, and press firmly until it is fully seated on the wall. Insert the
screw and gently tighten it until the mounting plate is secure. Do not
overtighten.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy. if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the radio or TV antenna.
- Increase the separation between the lights and the radio or TV.
- Consult the dealer or an experienced radio/TV technician for help.
Limited 2 Year Warranty
This product is guaranteed against defect and workmanship for a period of 2
years from the date of purchase. If the product fails during normal use,
please return it to the place of purchase together with a copy of the sales
receipt. Alternatively, you may contact us at infoefulcrumproducts.com and we
will arrange to have the product replaced or repaired at our discretion.
WARNING: Modifications to this or other products by anyone other than an
authorized repair agent may void that product’s warranty.
Specifications — Model # 30019-308
Operating Mode: 433MHz radio frequency control
Operating Distance: 60′
Battery Type: AM (x2), alkaline recommended
Battery Standby Life: approx. 30 months, actual
battery life will vary according to the frequency of use.
Included Items
Double-sided adhesive tape • Screws & drywall anchors Operating Instructions
CAUTION Do not mix battery types Use only fresh batteries for reliable
operation
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Fulcrum Products, Inc.
• into@LightitLED.com
• 503-274-1227
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>