MaxLite ML9LAABN23CS LED Architectural Wall Sconce User Manual
- June 9, 2024
- MaxLite
Table of Contents
ML9LA Series
Operating Instructions
MaxLite® LED Architectural Wall Sconce
Picture is for illustration purposes only. Your model may vary.
General Safety Information
- To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
- Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
- For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
- DO NOT INSTALL DAMAGED PRODUCT!
- This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
WARNING:
-
Risk of Fire – Supply conductors (power wires) connecting the fixture must be rated minimum 90℃.
If uncertain consult an electrician. -
Risk of Fire/Electric Shock – If not qualified, do not attempt installation. Contact a qualified electrician.
CAUTION:
- For your safety read and understand instructions completely before starting installation.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Before attempting installation, check your local electrical code, as it sets the wiring standards for your locality.
NOTES:
- If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch.
- Make certain no bare wires are exposed outside the wire nut connectors.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- Warranty is not applicable to lamps not installed in compliance with:
– National Electrical Code (NEC)
– The Standard for Safety of Underwriters Laboratories Inc. (UL)
Illustrations on the manual are for installation purposes only. It may not be
identical to the fixture purchased.
Models:
ML9LARBN Series
ML9LAABNCS Series
Input Rating: 120VAC 60Hz
Operating Temperature: -20C° to 40°C
Damp Location Rated
General Wiring Diagram
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
- Connect the black fixture wire to the (+) LINE supply wire.
- Connect the white fixture wire to the (-) COMMON supply wire.
- Connect the green fixture wire to supply ground wire.
WARNING: RISK OF ELECTRICAL SHOCK
- Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
- Turn off the power when you perform any maintenance.
- Verify that supply voltage is correct by comparing it with the luminaire label information.
- Make all electrical and grounded connections in accordance with the National Electrical Code and any applicable local code requirements.
- All wiring connections should be capped with UL approved wire connectors.
-
Slide diffuser upwards to remove from fixture.
-
Install screws on the junction box.
(Take out screws in attached bags; partially tighten the machine screws in the junction box.) -
Connect LED wire.
(Take out wire connectors in attached bags, connect the input wire from fixture with internal wire from the junction box ground wire to ground wire, L to L, N to N.)
-
Install the Base Plate.
(Align the holes of the rear plate of the light fixture with the machines screws and turn clockwise locking the plate into place. Tighten the machine screws, make sure the plate is fixted firmly.)
Note A: Use M4*30 screw to connect the lamp body on the junction box.
Note B: For CCT selectable models, select the preferred CCT. (See Fig B)
- Install the cover.
(Reinstall the diffuser, by turning the glass clockwise until securely fastened.)
Install the plastic housing to the lamp body.
Warranty Information
MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from
the date of original purchase from MaxLite or its authorized
distributor/dealer (the “Warranty Period”), as follows: If a Product fails to
operate during the Warranty Period as a result of defects in materials or
workmanship, MaxLite will, at its option, repair it, replace it with the same
or like Product.
Please refer to Maxlite’s website (at
http://maxlite.com/resources/warranties) for the complete terms and
conditions of our warranty.
Limitation of Liability
THE FOREGOING WARRANTY IS EXCLUSIVE, AND IS THE SOLE REMEDY FOR ANY AND ALL
CLAIMS, WHETHER IN CONTRACT, IN TORT OR OTHERWISE ARISING FROM THE FAILURE OF
PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH
WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED TO THE EXTENT PERMITTED BY LAW AND,
IN ANY EVENT, SHALL BE LIMITED TO THE WARRANTY PERIOD SPECIFIED ABOVE. THE
LIABILITY OF MAXLITE SHALL BE LIMITED TO THE TERMS OF THE EXPRESS WARRANTY SET
FORTH HEREIN. IN NO EVENT WILL MAXLITE BE LIABLE FOR ANY SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES RESULTING FROM
LOSS OF USE, PROFITS, BUSINESS OR GOODWILL, LABOR COSTS, REMOVAL OR
INSTALLATION COSTS, DECREASE IN THE LIGHT OUTPUT OF THE LAMP, AND/OR
DETERIORATION IN THE LAMP’S PERFORMANCE, WHETHER OR NOT MAXLITE HAS BEEN
ADVISED OF THE POSSIBILITY THEREOF. UNDER NO CIRCUMSTANCES SHALL MAXLITE’S
ENTIRE LIABILITY FOR A DEFECTIVE PRODUCT EXCEED THE PURCHASE PRICE OF THAT
PRODUCT. WARRANTY SERVICES PROVIDED UNDER THESE TERMS AND CONDITIONS DO NOT
ENSURE THE UNINTERRUPTED OPERATION OF PRODUCTS; MAXLITE SHALL NOT BE LIABLE
FOR DAMAGES CAUSED BY ANY DELAYS INVOLVING WARRANTY SERVICE.
This Limited Warranty gives you specific legal rights and you may also have
other rights that may vary from state to state. Because some states or
jurisdictions do not allow the exclusion or limitation of liability for
consequential or incidental damages, this limitation may not apply to you.
© Copyright 2021. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006
Tel: 973-244-7300
Fax: 973-244-7333
Email: info@maxlite.com
REV: 8/02/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>