Xiao Hao Poooli L3 Smart Pocket Printer User Guide
- June 5, 2024
- Xiao Hao
Table of Contents
Quick Start Guide
Poooli L3
Packing List
Poooli L3 Quick Start Guide
Thermal Paper Roll USB Cable
Note: The packing items are actually based on the order.
Appearance
- LED Indicator
- Power Button
- Paper Outlet
- Cover Opening Button
- TYPE-C Charging Port
- TPH
- Paper Guide
- Platen
- Fastener for Top Cover
- Reset Button
Using Guide
LED Indicator Status
- Green LED is lighting: power on/standby/fully charged/printing
- Green LED is slowly flashing: receiving gray-scale data
- Green Notify LED is slowly flashing: charging/firmware updating
- Red LED is lighting: cover opened/out of paper
- Red LED is quickly flashing: low-power status (quick flash twice, slow flash once)/TPH over temperature
- Red LED is slowly flashing: label positioning failure
Charging
Use it for the first time after purchase
- Recommended to use after full charge
- For computer USB port charging only
USB Cable
In addition to the supplied USB cable, you can also use the charging cable
of mobile device
- Recommended to use the supplied USB charging cable to charge
- It takes about 3.5 hours to charge with 5V/1A
Paper Purchase
From APP, Tmall, Jingdong Mall
- Official website (www.poooli.com)
Download APP
Scan the QR code below or search for “Poooli” in the app store to download and install the app:
Official WeChat service:
Official Weibo service:
Connection
Register and log in to the app, click Add Device. Connect to the device by searching for Bluetooth or scanning code.
APP Setting
Bluetooth 4.0
Bluetooth pairing
- If the first connection succeeds, the next time you start the application, it will be automatically connected to Poooli.
Simple operation
APP setting
- You can view information such as remaining power, firmware versions in device management.
Replace Supplies
1. Place the printer on the flat surface.
Please be careful about your fingers when holding the printer.
2. Press the cover opening button, and the top cover will be opened automatically.
When changing supplies, do not touch the print head in case of overheating.
3. Insert two paper guides into the corresponding place (57.8/80/110) according to the paper width, and then place the paper roll.
Note:
Insert tie paper guides into the slot of each value and make them fixed, then
place the paper roll.
-
2-inch width: insert two paper guides into the place of 57.8 as the figure shown below:
-
3-inch width: insert two paper guides into the place of 80 as the figure shown below:
-
4-inch width: insert two paper guides into the place of 110 as the figure shown below:
4. Pull the end of the paper roll towards the paper outlet, then close the cover.
Official Supplies Types
Self-adhesive Paper| With adhesive backing, cuttable size, can be preserved
for 10 years
---|---
Ten-year Thermal Paper| Clear printing, stable color rendering, suitable for
daily use, can be preserved for 10 years
Gray-scale Paper| Suitable for photo printing, waterproof, oil proof and
scratch proof, can be preserved for 7 years
Label Paper| Stickers with adhesive backing, fixed size, car be preserved for
10 years
Affordable Thermal Paper| Affordable, suitable for text printing, can be
preserved for 2 years
All Poooli paper does not contain bisphenol-A.
If the printer failure is caused by using other paper, you will not be able to
enjoy the three guarantees policy.
Safety
Battery Overheating
Battery Management and Cautions
- When charging is completed, please unplug the USB cable.
- To avoid fire, do not charge at high temperature (e.g. sweating rooms, bonfire nearby, etc.).
Charger Attention
Print Head Management and Cautions
- There may be damage to the print head due to improper charging.
- We recommend not to use Poooli in high humidity or dusty areas.
Burn Hazard
Print Head Overheating
- After printing, do not touch the print head directly to prevent burn.
Charging Port Damage
Charging Cautions
- Please gently insert or unplug the USB cable to prevent excessive damage to the charging port.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
FCC ID: 2AUJS-L3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>