ZEBRA MC2700 Mobile Computer User Guide
- June 5, 2024
- ZEBRA
Table of Contents
ZEBRA MC2700 Mobile Computer
Regulatory Information
This device is approved by Zebra Technologies Corporation. This guide applies to the following model numbers:
- MC27AK
- MC27BK
- MC27AJ
- MC27BJ
- MC27CK
- MC27CJ
All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required.
CAUTION: Only use Zebra approved and NRTL-certified accessories, battery
packs, and battery chargers. Do NOT attempt to charge damp/wet mobile
computers, printers or batteries. All components must be dry before connecting
to an external power source.
Bluetooth® Wireless Technology This is an approved Bluetooth® product. For
more information on the Bluetooth SIG listing, please visit www.bluetooth.com.
Regulatory Markings
Regulatory markings subject to certification are applied to the de-vice
signifying the radio(s) is/are approved for use. Refer to the Declaration of
Conformity (DoC) for details of other country markings. The DOC is available
at: www.zebra.com/doc.
To access e-label information, go to Settings >>> Regulatory
Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer about any equipment that has been added to your vehicle. Position the device within easy reach. User should be able to access the device with-out removing their eyes from the road.
IMPORTANT: Before installing or using, check national and local laws regarding distracted driving.
Safety on the Road
Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the areas where you drive. The wireless industry reminds you to use your device / phone safely when driving. Restricted Use Locations Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in restricted use locations. Safety in Hospitals and Aircraft
NOTE: Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircraft’s operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied. The
device complies with internationally recognized standards covering human
exposure to electromagnetic fields. For information on international human
exposure to electromagnetic fields, refer to the Zebra Declaration of
Conformity (DoC) at www.zebra.com/doc. Use only Zebra tested and approved
headset, belt-clips, holsters, and similar accessories to ensure RF exposure
compliance. If applicable, follow the instructions for use as detailed in the
accessory guide. The use of third-party belt clips, holsters, and similar
accessories may not comply with RF exposure compliance requirements and should
be avoided. For further information on the safety of RF energy from wireless
devices, refer to RF exposure and assessment standards section at
www.zebra.com/responsibility.
LED Devices Classified as ‘EXEMPT RISK GROUP’ according to IEC 62471:2006 and
EN 62471:2008. Pulse Duration: 22.8 ms or CW (MC2700 with SE4100)
Power Supply
WARNING ELECTRICAL SHOCK: Use only a Zebra-approved, Certified ITE [LPS] power supply with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous.
Batteries and Power Packs
This information applies to Zebra-approved batteries and power packs containing batteries.
Battery Information
CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to instructions.
Use only Zebra approved batteries. Accessories which have battery charging
capability are approved for use with the following battery models:
Model BT-000418 (3.6 VDC, 3300 mAh)
Zebra approved rechargeable battery packs are designed and constructed to the
highest standards within the industry. However, there are limitations as to
how long a battery can operate or be stored before needing replacement. Many
factors affect the actual life cycle of a battery pack such as heat, cold,
harsh environmental conditions, and severe drops.
When batteries are stored over six months, some irreversible deterioration in
overall battery quality may occur. Store batteries at half charge in a dry,
cool place, removed from the equipment to prevent loss of capacity, rusting of
metallic parts, and electrolyte leakage. When storing batteries for one year
or longer, the charge level should be verified at least once a year and
charged to half charge. Replace the battery when a significant loss of run
time is detected.
• Standard warranty period for all Zebra batteries is one year, regardless if
the battery was purchased separately or included as part of the host device.
For more information on Zebra batteries, please visit:
www.zebra.com/batterydocumentation and select the Battery Best Practices link.
Battery Safety Guidelines
- IMPORTANT – SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
- WARNING – When using this product basic safety precautions should always be followed, including the following:
The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment.
- Read all the instructions before using the product.
- Follow battery usage, storage, and charging guidelines found in the user’s guide.
- Improper battery use may result in a fire, explosion, or other hazard.
- To charge the mobile device battery, the battery and charger temperatures must be between 0°C and +40°C (+32°F and +104°F).
- Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any
- questions about the compatibility of a battery or a charger, contact Zebra support.
- Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
- Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
- Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
- Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard. Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source.
- Do not place battery into a microwave oven or dryer. To reduce the risk of injury, close supervision is necessary when used near children.
- Please follow local regulations to promptly dispose of used re-chargeable batteries.
- Do not dispose of batteries in fire. Exposure to temperatures over 100°C (212°F) may cause explosion. Seek medical advice immediately if a battery has been swallowed.
- In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
- If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection.
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with
Directives 2014/53/EU and 2011/65/EU.
Any radio operation limitations within EEA countries are identified in
Appendix A of EU Declaration of Conformity. The full text of the EU
Declaration of Conformity is available at: www.zebra.com/doc.
Waste Electrical and Electronic Equipment
(WEEE)
For EU Customers: For products at the end of their life, please refer to
recycling/disposal advice at: www.zebra.com/weee.
FCC STATEMENT
United States and Canada Regulatory Radio Frequency Interference Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada Innovation, Science and
Economic Development CanadaICES-003 Compliance Label: CAN ICES-3
([B])/NMB-3([B])
This device complies with Innovation, Science and Economic Development
Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause interference; and (2) This device
must accept any interference, including interference that may cause undesired
operation of the device.
RF Exposure Requirements – FCC and ISED
The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid.
Handheld Devices
To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1 cm or more from a user’s body and nearby persons.
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those already approved in this filling.
Hotspot ISED Notice
When operating in hotspot mode, this device is restricted to indoor use when operating in the 5150 – 5350 MHz frequency range.
UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the Global Positioning System (GPS) hardware, operating software, or other aspects of this product. UL has only tested for fire, shock, or casualties as outlined in UL’s Standard(s) for Safety for Information Technology Equipment. UL Certification does not cover the performance or reliability of the GPS hardware and GPS operating software. UL makes no representations, warranties, or certifications whatsoever regarding the performance or reliability of any GPS related functions of this product.
India
The sending and receiving of texts is supported in the following Indian
languages: Assamese, Bengali, Gujarati, Hindi, Kannada, Kashmiri, Konkani,
Malayalam, Manipuri, Marathi, Nepali, Oriya, Punjabi, Sanskrit, Sindhi, Tamil,
Telugu, Urdu, Bodo, Santhali, Maithili, and Dogri.
Warranty
For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.
Service Information
Before you use the unit, it must be configured to operate in your facility’s
network and run your applications.
If you have a problem running your unit or using your equipment, contact your
facility’s Technical or System Support. If there is a problem with the
equipment, they will contact Zebra support at
zebra.com\support.
For the latest version of the guide go to:
zebra.com\support.
Additional Information
For information on using the MC2700, refer to the MC2700 product guide available at: zebra.com/support.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>