REALTREE RLT6005 Tackle Box Bluetooth Speaker User Manual
- June 5, 2024
- REALTREE
Table of Contents
RLT6005 Tackle Box Bluetooth Speaker
User Manual
Important Information
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USING
KEEP INSTRUCTIONS FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTION
Please read below safety warnings carefully. If you don’t read, don’t understand, and don’t comply, there is the possibility to cause death and serious human & property damages. death and serious human & property damages.
- Do not use a speaker near water.
- Clean only with a dry cloth. Disconnect the power cord from the outlet before cleaning.
- Only use the original power cord supplied with the speaker.
- Do not place near heat sources including radiators, ovens, etc.
- Do not use it if the power cord or speaker has been damaged.
- Do not make any modifications to the speaker.
- Carefully arrange the power cord so it can not be tripped over or pulled by children.
- Please put the power button in the “OFF” position when charging the battery.
- Please do not overcharge the battery. the standard charging time is Max.6 hours. overcharge the battery may cause danger.
- Please do not soak the bag in water. the electronic part has a limited function of waterproofing, soaking the bag in water will destroy it.
Package
Interface Description
- Power Code (input 5V 1A)
- Power Switch ON/OFF
Charging instructions:
Charging | Insert the power cord to charge. |
---|
Red light indicates that the unit is charging.
The red light turns off when fully charged.
Do not charge for more than 6 hours even if the red light stays on.
Unplug the power cord once charging is complete.
Playtime| More than 3 hours at 50% volume.
Bluetooth Pairing
|
---|---
1. Press the Power Switch to the “ON” position to power on your speaker.| 2.
The LED Indicator Light will turn blue and rapidly fash to indicate that your
speaker is in pairing mode.
|
3. G0 to the Bluetooth settings menu on your phone.
Make sure that Bluetooth is turned on. Connect to the device listed as
“RLT6005.”| 4. The Bluetooth Indicator Light will stop blinking and remain
blue to indicate that your speaker is paired with your phone. Note that the
light may blink slowly anytime music is playing.
Specification
Function | Specification |
---|---|
Distance | 6.0m at Max |
Frequency Range | 2.402GHz-2.48GHz |
Power Supply | Built Chargeable Li-ion Battery |
Playtime | more than 3hrs at 50% volume |
RMS | 5W+5W |
Driver Impedance | 40 |
Frequency Response | 90Hz-20KHz |
Working Temperature | 10 C ~ 40 C |
Waterproof IPxx | IP41 |
FCC Statement:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator& your body.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.