Cwce Lighting HN030-01 WiFi Module User Manual

Cwce Lighting HN030-01 WiFi Module User Manual

Product overview

Shw-tuyawb3s-0-10v is a low-power independent WiFi protocol module jointly developed by Sunhiway Electronics using graffiti intelligent 1835.
It consists of a high level of integration of radio frequency chip BK7231T and a small number of peripheral devices, built-in Wi-Fi network protocol stack and rich library functions.
WB3S also includes 32-bit MCU with low power consumption, ITIR WLAN, the highest master frequency of 120MHz, built-in 256K SRAM,2Mbyte FIFlash and abundant peripheral resources. W83S is an RTOS platform, which integrates all function libraries of Wi-Fi MAC and TCP/IP protocols. On this basis, Sunhiway converts 3.3V PIM driver signal into 0-10V voltage signal, which can be applied to products with 0-10V signal externally.

features

• Operating voltage range :5V-12V(Iimit 15V)
• Built-in 32-bit LOW-power CPU, which doubles as an application processor
• frequency 120 1612
• Peripherals: 9XGPIOs, 1XUART, IXADC
• Wi-Fi connectivity 802.11 b/g/n
• channel I-11 412.4ghz
• Support REP, WPAAPA2, PSK(AES) safe mode
• Operating temperature: -20t to 801:
• BLE \ Support los. power Bluetooth

Application Fields

• Smart buildings
• Smart home/appliances
• Smart socket, smart lamo
• Industrial wireless control
• 0-10V dimming products

Module interface

Dimensional packaging

There are three pins. Size: 48mm (W))(2.8mm (L) XlImm (II).
Note: The default size tolerance is ± 0.35mm. If the customer has specific requirements for the key size, please communicate it in the specification.
Perform explicit calibration.

Pin definition

Pin symbol function

1. pin GND power reference ground
2. pins +12V power supply pin, working voltage range :5V-12V(limit 15V)
3. -pin 0-10V 0-10V signal output control pin

Electrical parameters

Parameter describes the minimum maximum unit

Storage temperature -40, 150 ‘C

Electrostatic discharge voltage

TAMB=-25°C 2 KV
Electrostatic discharge voltage

TAMB=-25°C 0.5kV
VCC supply voltage 5F I5V

Working Conditions

Parameter describes the minimum value a typical unit of maximum value
Ta operating temperature -20-85
VCC power supply voltage: 10.5, 12, 15 V

FCC Statement

FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247
Integral PCB antenna with antenna gain OdBi
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device If not to apply for any further FCC approval related to SAR, etc. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID:2AXAA-HNO30-01 Or Contains FCC ID:2AXAA-HNO30-01′
When the module is installed inside another device, the user manual of the host must contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

   • This device may not cause harmful interference.

   • This device must accept any interference received, including interference that may cause undesired operation.
     Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against hamiful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

   • Reorient or relocate the receiving antenna.

   • Increase the separation between the equipment and receiver.

   • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

   • Consult the dealer or an experienced radio/TV technician for help.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturers instructions as described in the user documentation that comes with the product.

Any company of the host device which install this modular should perform the test of radiated & conducted emission and spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 &15.207 ,158 Class B requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 &15.207 ,15B Class B requirement, then the host can be sold legally.

WIFI MODULE
Model No: HN030-01
FCC ID: 2AXAA-HN030-01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>