STREAMLINE FP-TR2000-03 230v Mains Powered Filterplus Mobi Maxi Single Double Filtration System Instruction Manual

June 5, 2024
Streamline

STREAMLINE FP-TR2000-03 230v Mains Powered Filterplus Mobi Maxi Single

Double Filtration System

STREAMLINE® Warranty

The warranty on all Machines and Equipment is for 1 year (12-months) from the RECORDED DATE OF PURCHASE. THIS WARRANTY EXCLUDES NORMAL MAINTENANCE ITEMS, including but not limited to HOSES, FILTERS, O-RINGS, DIAPHRAGMS, VALVES, GASKETS, CARBON BRUSHES and damage to motors and other components as a result of failure to replace normal maintenance items. THIS LIST IS NOT EXHAUSTIVE. If STREAMLINE® receives notice of such defects during the warranty period, STREAMLINE® will either, in its opinion, repair or replace components that prove to be defective. Replacement parts will only be supplied under warranty, upon the inspection and approval of the defective parts by STREAMLINE®. Should it be necessary to supply replacement parts before the opportunity to inspect, these will be charged at current prices and a credit will only be issued upon subsequent inspection and warranty approval by STREAMLINE®. The customer is responsible for the cost of the return of the defective part. If the warranty is approved, STREAMLINE® will pay for the cost of the repaired or replacement part. This warranty excludes the following conditions and circumstances which are at the discretion of STREAMLINE®

Wear and tear, misuse, abuse improper maintenance, frost damage, the use of chemicals other than those supplied or approved by STREAMLINE®, improper installation or repair, unauthorized modification, incidental or consequential costs, loss or damage, service, labor, or third-party charges, the cost of returning defective parts to STREAMLINE®. This warranty constitutes the exclusive remedy of any purchaser of a STREAMLINE® unit and is in lieu of all other warranties, express or implied, including without limitation any implied warranty of merchantability or fitness for use, to the fullest extent permitted by law. In no event shall any implied warranty of merchantability or fitness for use exceed the term of the applicable warranty stated above and STREAMLINE® shall have no other obligation or liability.

Important Unfortunately, these rights cannot be transferred to a third party.

Responsibilities

General Responsibilities

  • These operating instructions allow you to use the FILTERPLUS® MOBI® filtration system safely and efficiently. The instructional booklet must be read before setting up, starting, or using your STREAMLINE® equipment. It is an integral part of the product itself.
  • Please keep this booklet in a safe place near your FILTERPLUS® MOBI® filtration system for future consultation. Your FILTERPLUS® MOBI® filtration system is constructed according to current safety standards and regulations. The latest and current edition is illustrated in this manual. The contents of this booklet should be bought to the attention of all users.

Manufactures Responsibilities

  • VARITECH SYSTEMS Ltd the manufacturer of STREAMLINE® holds a 12-months warranty on all machines and equipment from the date of purchased (see Warranty section 2)
  • VARITECH SYSTEMS Ltd the manufacturer of STREAMLINE® is in no case responsible for failures or errors caused by modifications to the unit by customer or other persons.

Personnel Responsibilities

The FILTERPLUS® MOBI® filtration equipment is designed and manufactured to be operated in industrial applications. It is important that the operator(s) of the FILTERPLUS® MOBI® filtration equipment have read through these operating instructions thoroughly, and understand all safety instructions and regulations. The FILTERPLUS® MOBI® filtration equipment is not intended for use by children, adolescents, persons under the influence of alcohol / drugs or simply lacking experience and knowledge. These operating instructions are designed to educate the user, informing the operator how to carry out the task at hand successfully, whilst avoiding potential dangers that might occur.

If needed, training videos can be found on the manufacturer’s website: www. streamline.systems

Technical Specifications

Specification Data

PRODUCT CODE FP-TR2000-03 FP-TR3000-03
Country of Origin United Kingdom United Kingdom
Maximum Height 1340mm 1340mm
Maximum Length 600mm 600mm
Maximum Width 450mm 450mm
Dry Weight 54kg 62kg
Wet Weight 56kg 64kg
Inlet Pressure Requirement 2.8bar / 40psi 2.8bar / 40psi
Optimum Operating Pressure 8.2bar / 120psi 8.2bar / 120psi
Standard Water Inlet Connection (Male hose lock) 3/4 inch 3/4 inch
Waste Water Outlet Connection (Male hose lock) 3/4 inch 3/4 inch
Pure Water Outlet Connection (Male hose lock) 3/4 inch 3/4 inch
Electrical Power Supply 230V mains 230V mains
Optimum Water Quality 000ppm 000ppm
Water Quality Range 000ppm – 1000ppm 000ppm – 1000ppm
Pure Water Flow (optimum output) 6.8Lpm 9.6Lpm
Waste Water Flow 4.5Lpm 6.4Lpm
Operating Time Continual Continual

Parts and Accessories

The FILTERPLUS® MOBI® filtration system will include the following parts

  • 1x 3mtr length of black Standard Water Inlet hose with stainless steel connections
  • 1x 3mtr length of red Waste Water Outlet hose with stainless steel connections
  • 2x 3mtr length of blue Pure Water Outlet hose with stainless steel connections
  • SPAN3 filter spanner for changing filters

STREAMLINE FP-TR2000-03 230v Main-Fig3

Electrical Specifications & Safety

This applies to both FP-TR2000-03 and FP-TR3000-03 FILTERPLUS® MOBI® filtration systems. Please check that the installation and sockets are adequate for the maximum power of the appliance indicated on the rating plate. If in doubt, consult a qualified electrician. The correct plug should be fitted by a qualified electrician. Stay alert, watch what you are doing, and use common sense when operating the FILTERPLUS® MOBI® filtration system. Do not use the filtration system while you are tired or under the influence of alcohol, drugs, or medication. A moment of inattention while operating the filtration trolley may result in serious personal injury. Additional protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection may be required depending on the safety regulations in the operator’s surroundings. The water cannot be used for human consumption. Use personal protective equipment to avoid personal injury

  • VARITECH SYSTEMS Ltd, the manufactures of STREAMLINE®, declines all liability for damage caused by the faulty earthing of the appliance.
  • VARITECH SYSTEMS Ltd, the manufacturer of STREAMLINE® declines all liability for damage to persons, animals or things caused by faulty or incorrect connection. – Before connecting the equipment, check that the specification given on the rating plate corresponds to that of the mains electrical supply.
  • If the equipment is connected via an extension, use cables with an adequate cross-section, never less than 1,5 mm. The plug and socket must be watertight.
  • The electrical safety of the equipment is guaranteed only when correctly and efficiently earthed as specified in current electrical safety legislation (in compliance with the provisions of the IEC 60364-1 standard). This fundamental safety requirements should be verified. If in doubt, ask a professionally qualified electrician to check the system thoroughly. It is recommended that the electric supply to this machine should include a residual current device that will interrupt the supply if the leakage current to earth exceeds 30 mA for 30ms or a device that will prove the earth circuit.

The equipment can be disconnected from the mains only by unplugging the plug from the mains socket.

  • When using any electrical appliance, certain fundamental rules should be respected
  • Do not touch the appliance with wet hands or feet
  • Do not touch the appliance with bare feet or unsuitable clothing
  • Do not pull the power cable or appliance itself to unplug the plug from the mains.

Personal Safety

Stay alert, watch what you are doing, and use common sense when operating the FILTERPLUS® MOBI® filtration system. Do not use the filtration system while you are tires or under the influence of alcohol, drugs, or medication. A moment of inattention while operating the filtration trolley may result in serious personal injury.

STREAMLINE FP-TR2000-03 230v Main-Fig4

System Safety

The FILTERPLUS® MOBI® filtration trolley is manufactured with the safety of the operator in mind, including some key features such as; result in serious personal injury

Over Pressure

If the water pressure in the FILTERPLUS® MOBI® filtration system is above the standard 10bar pressure, the pressure relief valve opens on the pump allowing a greater flow through the wastewater outlet, reducing the pressure in the system and through the pure water outlet • It is important to never open the filter vessels or membrane housings during operation or whilst under pressure

Over Heating

If the powerful booster pump overheats on the FILTERPLUS® MOBI® filtration system, an activation switch is triggered and the system will automatically switch off.

Electrical Hazards

As the FILTERPLUS® MOBI® filtration system is powered by an electrical source, never use the equipment in the rain, snow or strong winds. • Never use the filtration system to clean people and/or animals. • Before each use, undertake a visual check on all electrical cables for damage. Never use the filtration system with a damaged cable.

Mechanical Hazards

  • To avoid all mechanical hazards, place the FILTERPLUS® MOBI® filtration trolley on an even surface only, and ensure sufficient stability.

Operating the FILTERPLUS® MOBI® Filtration System

Use only original accessories that come with the FILTERPLUS® MOBI® filtration system, offering maximum quality and security. Failure to use original accessories absolves VARITECH SYSTEMS Ltd, the manufacturer from all liability.

When purchasing the product, make sure it has an identification plate. If this is missing, notify the distributor/manufacturer where you purchased the unit from. The use of an appliance without an identification plate absolves the manufacturer from all liability. Products without an identification plate should be considered anonymous and potentially dangerous.

Unpacking the FILTERPLUS® MOBI® filtration system

Your FILTERPLUS® MOBI® Filtration System has been carefully manufactured, checked through QC and packaged as a kit. Carefully unpack your new FILTERPLUS® MOBI® Filtration System and carry out a thorough visual check on all parts. If in doubt, do not use the system. Contact your dealer and/or manufacturer. Packaging (bags, boxes, nails, tape, etc.) should be kept out of reach of children as they may represent a potential hazard. Packaging can be recycled according to your local legislation.

Storage of the FILTERPLUS® MOBI® filtration system

Short term and long-term storage are important issues. The FILTERPLUS® MOBI® filtration system must be protected from algae and bacteria growth in the pressure vessels caused by stagnant water. The reverse osmosis (RO) membranes and de-ionizing (DI) resin must not dry out wither.

Important The unit must be protected from freezing.

Storage of your system

Short term storage: 2-4 weeks of no use

  • Remove the prefilter housing and pour out the excess water.
  • Remove the DI resin cartridge housing and pour out the excess water.
  • Remove the RO membrane caps and lay down the trolley unit for the excess water to drain from the membranes.
  • Ensure you reinstall the top caps on RO pressure vessels. Do not allow them to dry out. v. Ensure you reinstall the prefilters and DI resin cartridge. Do not allow them to dry out.
  • Long term storage
  • 4 weeks plus of no use vi. Remove the prefilter housing and pour out the excess water.
  • Remove the DI resin cartridge housing and pour out the excess water. veniremen the RO membrane caps and lay down the trolley unit for the excess water to drain from the membranes.
  • Remove all filters from the trolley system, wrap in individual plastic bags and seal.
  • Replace all filter housings and membrane caps without any filters inside.
  • It is important to store the trolley system where it cannot freeze.
  • It is important for all filters to not be allowed to dry out when not in use.

About your system

STREAMLINE FP-TR2000-03 230v Main-Fig6 STREAMLINE FP-TR2000-03 230v Main-Fig7

  • To operate the FILTERPLUS® MOBI® filtration system, there needs to be accessible to a water supply and mains electricity.
  • The water enters the FILTERPLUS® MOBI® filtration trolley system through the water inlet connection and then passes through the carbon block prefilter removing the largest particles in the water before the water enters the membrane.
  • The reverse osmosis (RO) membrane filters remove up to 98% of the impurities in the water before it reaches the de-ionizing (DI) resin filter where the water is polished and reaches a 000ppm result.
  • From the RO membrane filters, wastewater is discharged through the wastewater outlet. This water is not harmful to the environment or skin, however full of impurities and therefore not suitable for cleaning.
  • In the FILTERPLUS® MOBI® filtration trolley system you have purchased, the booster pump is powered by 230V mains electricity

STREAMLINE FP-TR2000-03 230v Main-Fig8

Assembling the System

All main parts and safety devices are assembled by the manufacturer. Some other secondary parts may be supplied separately. These parts must be assembled by the user following the assembly instructions.

To use your FILTERPLUS® MOBI® filtration system

Ensure the trolley system is safely secure and stable on a level surface

Connect the BLACK hose from the mains water supply to the water inlet

Connect the RED hose from the wastewater outlet and direct it to a drain or nearby soak away

STREAMLINE FP-TR2000-03 230v Main-Fig11

Connect the 2x BLUE hose from the pure water outlet to your watered poles (it is possible to add a STREAMLINE® 100mtr hose reel)

STREAMLINE FP-TR2000-03 230v Main-Fig12

Plugin the system to the mains power supply

STREAMLINE FP-TR2000-03 230v Main-Fig13

Turning your FILTERPLUS® MOBI® Filtration System ON

Once the final position of the FILTERPLUS® MOBI® filtration system has been reached, you are now ready to switch on the water supply and power up the booster pump.

Switch on the water supply at the mains water tap and allow the FILTERPLUS® MOBI® filtration trolley to pressurized

STREAMLINE FP-TR2000-03 230v Main-Fig14

Inlet Pressure will show on the Pressure Gauge when the Mobi Maxi is running, this should be registering 100-120psi. Do not exceed 125psi.

STREAMLINE FP-TR2000-03 230v Main-Fig15

When pure water is following from the watered brush, switch on the booster pump by turning the ‘POWER’ switch to the ON position

STREAMLINE FP-TR2000-03 230v Main-Fig16

The pressure gauge should now be around 120 – 150 psi (8-10 bar)

STREAMLINE FP-TR2000-03 230v Main-Fig17

You are now good to use your FILTERPLUS® MOBI® filtration trolley system

Disconnect the mains power supply before disconnecting the mains water supply

STREAMLINE FP-TR2000-03 230v Main-Fig19

Remove all hoses and safely store them in a storage box

STREAMLINE FP-TR2000-03 230v Main-Fig20

Turning your FILTERPLUS® MOBI® Filtration System OFF

To switch off the FILTERPLUS® MOBI® filtration system after completing the cleaning task, simply:

turn the ‘POWER’ switch to the OFF position, switching off the booster pump

STREAMLINE FP-TR2000-03 230v Main-Fig18

Malfunctions and Troubleshooting

During the usage of the FILTERPLUS® MOBI® filtration system, there may be some small troubleshooting to undertake

Low water pressure or water supply at the watered brush

  • Check for any blockages or kinks in hose b. Disconnect all extension hose reels and connect the FILTERPLUS® MOBI® filtration system directly to the telescopic pole c. Clean or replace the sediment filter d. Contact service center
  • High wastewater flow and low pure water flow
  • Check if the membrane has the plug installed – if so, replace the membrane
  • Contact service center
  • High pure water TDS
  • Check membrane quality – replace membrane b. Check DI filter – replace resin beads in DI cartridge c. Contact service center
  • The booster pump will not start
  • Check the fuse on mains power b. Contact service center

Maintenance and Replacing Filters

Care and maintenance of your FILTERPLUS® MOBI® filtration system will ensure it is well looked after and running smoothly every time. It is recommended to run a weekly, monthly and quarterly examination on the FILTERPLUS® MOBI® filtration system to ensure all filters are adequate and effective for producing pure 000ppm water quality

Weekly inspections

  • Keep a check on the pure water TDS by using the inline TDS This measures in parts per million (ppm). If the output reads higher than 10ppm, it is recommended to change the de-ionizing (DI) filter, and make a note in the back of the inspection booklet

Monthly inspections

  • Each month it is recommended to flush through the reverse osmosis (RO) membranes and reset the ratio between pure water output and wastewater
  • The wastewater valve should be opened 100% to allow wastewater to flow out for 5mins. Gradually reset to 60% pure and 40% wastewater.

Quarterly inspections

  • Each month it is recommended to flush through the reverse osmosis (RO) membranes and reset the ratio between pure water output and wastewater
  • The wastewater valve should be opened 100% to allow wastewater to flow out for 5mins. Gradually reset to 60% pure and 40% wastewater.

Prefilters – usage and replacing

The sediment and carbon block 10inch prefilter is the first initial filter the feed water will pass through.

Usage

Either quarterly replacement or approx. 25,000ltrs of mains water running through, whichever comes quickest

How do I change the carbon prefilter?

  • With the use of the spanner which comes with the FILTERPLUS® MOBI® filtration system, simply unscrew the clear prefilter housing and dispose of the used carbon prefilter. Slide in the new CF10-F-001 STREAMLINE® 5micron prefilter into the prefilter housing and reattach to the filtration system. Ensure you safely and securing tighten up the housing to ensure the system is safe under operating pressure
  • Usage Either quarterly replacement or approx. 25,000ltrs of mains water running through, whichever comes quickest

How do I change the DI resin cartridge?

With the use of the spanner which comes with the FILTERPLUS® MOBI® filtration system, simply unscrew the membrane housing caps and remove the membranes one by one. Replace the 1x (or 2x) membrane with the V-MRO-4040-F from STREAMLINE®. Please pay special attention to the flow direction on the membrane housings and on the membranes themselves

  • Reverse Osmosis (RO) Membrane Filters – usage and replacing
  • The RO membranes are the core part of the water filtration – produce up to 98% of water filtration.
  • Usage Either yearly replacement or approx. 250,000ltrs of pure water running through, whichever comes quickest

How do I change the RO membranes?

With the use of the spanner which comes with the FILTERPLUS® MOBI® filtration system, simply unscrew the membrane housing caps and remove the membranes one by one. Replace the 1x (or 2x) membrane with the V-MRO-4040-F from STREAMLINE®. Please pay special attention to the flow direction on the membrane housings and on the membranes themselves

Disposing of filters and machine

The FILTERPLUS® MOBI® filtration system is classified as special waste. It must be taken apart and divided into uniform sections which should be disposed of according to current legislation. Do not use the components removed as spare parts. All filters are classified and disposable as unharmful general waste.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Streamline User Manuals

Related Manuals