KENWOOD KMM-205 Digital Media Receiver Instruction Manual

KMM-205 Digital Media Receiver
Instruction Manual

KMM-205 Digital Media Receiver

Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed of as household waste.
Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts.
Contact your local authority for details on locating a recycling facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment.
Notice: The sign “Pb” below the symbol for batteries indicates that this battery contains lead.

Declaration of Conformity with regard to the RE Directive 2014/53/EU
Declaration of Conformity with regard to the RoHS Directive 2011/65/EU

Hereby, JVCKENWOOD declares that the radio equipment
“KMM-205/KMM-125/KMM-105RY/KMM-105GY/
KMM-105AY” is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.kenwood.com/cs/ce/eudoc/

BEFORE USE

IMPORTANT

• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe the Warnings and Cautions in this manual.
• Please keep the manual in a safe and accessible place for future reference.

WARNING

• Do not operate any function that takes your attention away from safe driving.

Caution
Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using external devices if they might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• Depending on the type of car, the antenna will automatically extend when you turn on the unit with the antenna control wire connected (page 18). Turn off the unit or change the source to STANDBY when parking in a low-ceiling area.

How to read this manual

• Operations are explained mainly using buttons on the faceplate of KMM-205.
• English indications are used for the purpose of explanation. You can select the display language from the [FUNCTION] menu. (Page 5)
• [XX] indicates the selected items.
• (Page XX) indicates references are available on the stated page.

BASICS

Faceplate

• Press and hold to turn off the power.
Adjust the volume| Turn the volume knob.
Select a source| Press SRC repeatedly.
Change the display information| Press DISP repeatedly. (Page 14)

GETTING STARTED

1 Select the display language and cancel the demonstration

When you turn on the power for the first time (or after you reset the unit), the display shows: “SEL LANGUAGE”→ “PRESS” → “VOLUME KNOB”

1. Turn the volume knob to select [EN] (English), [RU] (Russian),
   [SP] (Spanish) or [FR] (French), then press the knob.
   [EN] is selected for the initial setup.
   Then, the display shows: “CANCEL DEMO”→ “PRESS” → “VOLUME KNOB”.

2. Press the volume knob again.
   [YES] is selected for the initial setup.

3. Press the volume knob again.
   “DEMO OFF” appears.

2 Set the clock and date

1. Press the volume knob to enter [FUNCTION].

2. Turn the volume knob to select [CLOCK], then press the knob.
   To adjust the clock

3. Turn the volume knob to select [CLOCK ADJUST], then press the knob.

4. Turn the volume knob to make the settings, then press the knob.
   Hour →Minute

5. Turn the volume knob to select [CLOCK FORMAT], then press the knob.

6. Turn the volume knob to select [12H] or [24H], then press the knob.
   To set the date
   7 Turn the volume knob to select [DATE FORMAT], then press the knob.
   8 Turn the volume knob to select [DD/MM/YY] or [MM/DD/YY], then press the knob.
   9 Turn the volume knob to select [DATE SET], then press the knob.
   10 Turn the volume knob to make the settings, then press the knob.
   Day Month Year or Month Day Year
   11 Press and hold to exit.
   To return to the previous setting item, press .

3 Set the initial settings

1. Press B SRC repeatedly to enter STANDBY.

2. Press the volume knob to enter [FUNCTION].
   • Pressing AUD enters [AUDIO CONTROL] directly.

3. Turn the volume knob to select an item (page 5), then press the knob.

4. Repeat step 3 until the desired item is selected or activated.

5. Press and hold to exit.
   To return to the previous setting item, press .

[AUDIO CONTROL]|
---|---
[SWITCH PREOUT]| [REAR]/[SUB-W]: Selects whether rear speakers or a subwoofer are connected to the line-out terminals on the rear (through an external amplifier). (Page 17)
[SP SELECT]| OFF/5/4/6×9/6/OEM: Selects according to the speaker size (5 inches or 4 inches, 6×9 inches or 6 inches) or OEM speakers for optimum performance.
[DISPLAY]
[EASY MENU]| (For KMM-125)
When entering [FUNCTION]…
[ON]: [ZONE 1] illumination changes to white color. ;
OFF: [ZONE 1] illumination remains as [COLOR SELECT] color. (Page 12)
•[ZONE 2] illumination changes to a light blue color when you enter [FUNCTION], regardless of the [EASY MENU] setting.
•Refer to the illustration on page 12 for zone identification.
[TUNER SETTING]
[PRESET TYPE]| [NORMAL]: Memorizes one station for each preset button in each band
(FM1/FM2/FM3/MW/LW).; [MIX]: Memorizes one station for each preset button, regardless of the selected band.
[SYSTEM]

[SOURCE SELECT]

(Page 10)
[P-OFF WAIT]| Applicable only when the demonstration mode is turned off.
Sets the duration when the unit will automatically turn off (while in standby mode) to save the battery.

[F/W UPDATE]
[UPDATE SYSTEM!

(upgrading is not activated).
For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.
[CLOCK]
[CLOCK DISPLAY]| [ON]: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels.
[ENGLISH]| Select the display language for the [FUNCTION] menu and music information if applicable.
By default, [ENGLISH] is selected.

RADIO

• “ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
• The unit switches to an FM alarm automatically when receiving an alarm signal from an FM broadcast.

Search for a station

1. Press SRC repeatedly to select RADIO.
2. Press BAND repeatedly to select FM1/FM2/FM3/MW/LW.
3. Press / T to search for a station.

You can store up to 18 stations for FM and 6 stations for MW/LW.

• To store a station: Press and hold one of the number buttons (1 to 6).
• To select a stored station: Press one of the number buttons (1 to 6).

Other settings

1. Press the volume knob to enter [FUNCTION].
2. Turn the volume knob to select an item (see the right column), then press the knob.
3. Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.
4. Press and hold to exit.

To return to the previous setting item, press .

[TUNER SETTING]|
---|---
[SEEK MODE]| Selects the searching method for / Howl buttons when pressed. jAUT011: Automatically search for a station.; [AUT02]: Search for a preset station. ; [MANUAL]: Manually search for the station.
[LOCAL SEEK]| [ON]: Searches only stations with good reception.; JOFF1: Cancels.
•Settings made are applicable only to the selected source/station. Once you change the source/station, you need to make the settings again.
[AUTO MEMORY]| [YES]: Automatically starts memorizing 6 stations with good reception.; IN01.: Cancels.
•Selectable only if [NORMAL] is selected for [PRESET TYPE]. (Page 5)
[MONO SET]| [ON]: Improves the FM reception, but the stereo effect will be lost.; TOFF’: Cancels.
[NEWS SET]| [ON]: The unit will temporarily switch to News Programme if available.; OFF: Cancels.
[REGIONAL]| ON: Switch to another station only in the specific region using the “AF” control.; OFF: Cancels.
[AF SET]| ON: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor. ; OFF: Cancels.
[TI]| [ON]: Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up) while listening to all sources except in MW/LW.; JOFF1: Cancels.
[PTY SEARCH]| 1 Turn the volume knob to select the available Program Type (page 7), then press the knob.
2 Turn the volume knob to select the PTY language (IENGLISH1/ [FRENCH]/[GERMAN]), then press the knob.
3 Press Eel / 1 to start searching.
CLOCK|
---|---
[TIME SYNC]| [ON]: Synchronizes the unit’s time to the Radio Data System station time. ;

• [LOCAL SEEK]/[MONO SET]/[NEWS SET]/[REGIONAL]/[AF SET]/[TI]/[PTY SEARCH] is selectable only when the band is FM1/FM2/FM3.
• If the volume is adjusted during the reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

Available Program Type for [PTY SEARCH] [SPEECH]: [NEWS], [AFFAIRS], [INFO] (information), [SPORT], [EDUCATE], [DRAMA],
[CULTURE], [SCIENCE], [VARIED], [WEATHER], [FINANCE], [CHILDREN],
[SOCIAL], [RELIGION], [PHONE IN], [TRAVEL], [LEISURE], [DOCUMENT] [MUSIC]: [POP M] (music), [ROCK M] (music), [EASY M] (music), [LIGHT M] (music), [CLASSICS], [OTHER M] (music), [JAZZ], [COUNTRY], [NATION M] (music),
[OLDIES], [FOLK M] (music)
The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.

The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.

USB/iPod/ANDROID

Selectable source:
KMM-205 : USB/iPod USB/ANDROID
: USB/ANDROID

Start playback

The source changes automatically and playback starts.

[FILE REPEAT]/[FOLDER REPEAT]/[ALL REPEAT] : MP3/WMA/WAV/FLAC file
[FILE REPEAT]/[FOLDER REPEAT]/[REPEAT OFF] : iPod
Random play46| Press 3 repeatedly.
[FOLDER RANDOM]/[RANDOM OFF] : MP3/WMA/WAV/FLAC file or iPod
Press and hold 3 to select [ALL RANDOM].

1 KCA-iP102: 30-pin type, KCA-iP103: Lightning type
2 Do not leave the cable inside the car when not used.
3 You can control the Android devices using the Android device itself via other media player applications installed in the Android device.
4 Not applicable for ANDROID.
5 This does not work for iPod/ANDROID.
6 For iPod: Applicable only when [MODE OFF] is selected.

Select music drive

While in the USB source, press 5 repeatedly.
Stored songs in the following drive will be played back.

• The selected internal or external memory of a smartphone (Mass Storage Class).
• The selected drive of a multiple-drive device.

Listen to TuneIn Radio/TuneIn Radio Pro

While listening to TuneIn Radio or TuneIn Radio Pro, connect the iPod/ iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select control mode

While in the iPod USB source, press 5 repeatedly.
[MODE ON]: Control iPod using the iPod itself. However, you can still perform play/pause, file skip, fast-forward or fast-reverse from this unit.
[MODE OFF]: Control iPod from this unit.

Select a file from a folder/list

For iPod, applicable only when [MODE OFF] is selected.

1. Press .
2. Turn the volume knob to select a folder/list, then press the knob.
3. Turn the volume knob to select a file, then press the knob.

Quick search (applicable only for USB source)
If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.

Skip search (applicable only for iPod USB source)
Press / to search at a preset skip search ratio. (See the right column)

• Pressing and holding / searches at a 10% ratio.

Alphabet search (applicable only for iPod USB source)
You can search for a file according to the first character.

1. Turn the volume knob quickly to enter character search.

2. Turn the volume knob to select the character.
   • Select “ * ” to search for a character other than A to Z, 0 to 9.

3. Press / to move to the entry position.
   • You can enter up to 3 characters.

4. Press the volume knob to start searching.

To return to the root folder/first file/top menu, press 5.
To return to the previous setting item, press ****.
To cancel, press and hold .

Other settings

1. Press the volume knob to enter [FUNCTION].
2. Turn the volume knob to select an item (see the following table), then press the knob.
3. Repeat step 2 until the desired item is selected or activated.
4. Press and hold to exit.

To return to the previous setting item, press .

[USB]|
---|---
[MUSIC DRIVE]| [DRIVE CHANGE]: The next drive ([DRIVE 1] to [DRIVE 5]) is selected automatically and playback starts.
Repeat steps 1 to 3 to select the following drives.
 [SKIP SEARCH]| (For KMM- 205)
[0.5%]/[1%]/[5%]/[10%]: While listening to the iPod USB source, select the skip search ratio over the total files.

AUX

Preparation:

• Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT]. (Page 5)

1. Connect a portable audio player (commercially available).
   Auxiliary input jack
   

2. Press B SRC repeatedly to select AUX.

3. Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit…

1. Press the volume knob to enter [FUNCTION].

2. Turn the volume knob to select [SYSTEM], then press the knob.

3. Turn the volume knob to select [AUX NAME SET], then press the knob.

4. Turn the volume knob to select an item, then press the knob.
   [AUX] (default)/[DVD]/[PORTABLE]/[GAME]/[VIDEO]/[TV]

5. Press and hold to exit.

To return to the previous setting item, press .

AUDIO SETTINGS

Select the equalizer
(only for )

Press repeatedly to select a preset equalizer (which is suitable to the music genre) directly.

Preset equalizer: [DRIVE EQ]/[TOP40]/[POWERFUL]/[ROCK]/[POPS]/[EASY]/[JAZZ]/ [NATURAL]/[USER]

• You can also select the preset equalizer from the [AUDIO CONTROL] menu.
  (Page 11)

Other settings

1. Press AUD to enter [AUDIO CONTROL] directly.
2. Turn the volume knob to select an item (page 11), then press the knob.
3. Repeat step 2 until the desired item is selected or activated.
4. Press and hold to exit.

To return to the previous setting item, press .

[AUDIO CONTROL]

[SUB-W LEVEL]| [-151 to [+15] ([0])| ‘Adjusts the subwoofer output level.
[BASS LEVEL]| [-81 to [+81 (+21)| Adjusts the level to memorize for each source (Before making an adjustment, select the source to loll want to adjust.)
[MID-LEVEL]| [-8] to [+8] (1+1])
[THE LEVEL]| [-8] to [+8] ([+1])
[ERIC) PRO]| Adjusts your own sound settings.
•The settings are stored to [USER1 in [PRESET EQ1.
[BASS ADJUST]| [BASS CTR FRO] [60]/[80]/[100]/[200]: Selects the center frequency.
[BASS LEVEL] [-8] to [+8] (0_11): Adjusts the level.
[BASS Q FACTOR] [1.001/[1.25]/[1.50]/[2.00]: Adjusts the quality factor.

[MID ADJUST]| [MID CTR FRQ] [0.51(HZ]/[1.0KHZ]/[1.5KHZ]/[2.SKHZ]: Select the center frequency.
[MID LEVEL] [-8] to [+8] ([+1]): Adjusts the level.
[MID Q FACTOR] [0.751/11.001/11.251: Adjusts the quality factor.

the center frequency.
•[TRE LEVEL] [-8] to [+8] ([+1]): Adjusts the level.
: PRESET EQ]| [DRIVE EQ]/[TOP4OMPOWERFULMROCKMPOPSWEASYMAllY [NATURAL]/[USER]: Selects a preset equalizer suitable to the music genre.
•Select [USER] to use the settings made in [EQ PRO].
•[DRIVE EQ] is a preset equalizer that reduces noise outside the car or the running noise of the tires.
[BASS BOOST]| [LV1]/[LV2]/[LV3]: Selects your preferred bass boost level. ;

[LOUDNESS]| [LVII/[LV2]: Selects your preferred low and high frequencies boost to produce a well-balanced sound at a low volume level. ; OFF: Cancels.

[LPF SUBWOOFER]| [THROUGH]: All signals are sent to the subwoofer. ; [85HZ]/[120HZ]/[160HZ]: Audio signals with frequencies lower than 85 Hz/120 Hz/ 160 Hz are sent to the subwoofer.
[SUB-W PHASE]| [REVERSE] (180°)/[NORMAL] (0°): Selects the phase of the subwoofer output to be in line with the speaker output for optimum performance.
•Selectable only if a setting other than [THROUGH] is selected for [LPF SUBWOOFER].
[FADER]| [R15] to [F15] ([0]): Adjusts the rear and front speaker output balance.
[BALANCE]| [L15] to [R15] (101): Adjusts the left and right speaker output balance.
[VOLUME OFFSET]| For AUX: [-8] to [+8] ([0]); For other sources: [-8] to [0]: Presets the initial volume level of each source.
(Before adjustment, select the source you want to adjust.)
[SOUND RECNSTR] (Sound reconstruction)| [ON]: Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that is lost in audio data compression.; OFF: Cancels.

• [SUB-W LEVEL]/[SUBWOOFER SET]/[LPF SUBWOOFER]/[SUB-W PHASE] is selectable only if [SWITCH PREOUT] is set to [SUB-W]. (Page 5)
• [SUB-W LEVEL]/[LPF SUBWOOFER]/[SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON].

DISPLAY SETTINGS

KMM-125: Zone identification for color settings and brightness settings

• Press COL to change the illumination color (preset colors) of the last selected zone.
  By default, [ALL ZONE] is selected.

• Press and hold COL to enter [COLOR SELECT] directly.

: Zone identification for brightness setting

1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select an item (see the right column), then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.
4 Press and hold  exit.

To return to the previous setting item, press .

[DISPLAY]

[COLOR SELECT]| (For KMM-125)
Select illumination colors for [ALL ZONE], [ZONE 1], and [ZONE 2] separately.
1. Select a zone ([ZONE 1], [ZONE 2], ALL  ZONE]). (See the illustration in the left column.)
2. Select a preset color for the selected zone.
To make your own color, select [CUSTOM R/G/B].
The color you have made will be stored in  [CUSTOM R/G/B].
1. Press the volume knob to enter the detailed color adjustment.
2. Press S/T to select the color ([R]/[G]/[B]) to adjust.
3. Turn the volume knob to adjust the level ([0] to [9]), then press the knob.
[DIMMER]| Dims the illumination.
[ON]: Dimmer is turned on.
OFF: Dimmer is turned off.
[DIMMER TIME]: Set the dimmer on and off time.
1. Turn the volume knob to adjust the [ON] time, then press the knob.
2. Turn the volume knob to adjust the OFF time, then press the knob.
Default: [ON]: [18:00] ; OFF: [6:00]
[BRIGHTNESS]| 1. Select a zone. (See the illustration in the left column.)
2. [LVL 00] to [LVL 31]: Set the brightness level for the selected zone.
[TEXT SCROLL]| [ONCE]: Scrolls the display information once. ; [AUTO]: Repeats scrolling at
5-second intervals. ; OFF: Cancels.

Preset color:
[INITIAL COLOR]/[VARIABLE SCAN]/[CUSTOM R/G/B]/[RED1]/[RED2]/[RED3]/[PURPLE1]/ [PURPLE2]/[PURPLE3]/[PURPLE4]/[BLUE1]/[BLUE2]/[BLUE3]/[SKYBLUE1]/[SKYBLUE2]/
[LIGHTBLUE]/[AQUA1]/[AQUA2]/[GREEN1]/[GREEN2]/[GREEN3]/[YELLOWGREEN1]/
[YELLOWGREEN2]/[YELLOW]/[ORANGE1]/[ORANGE2]/[ORANGERED]

REFERENCES

Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector
Detach the faceplate and clean the connector gently with a cotton swab. Be careful not to damage the connector.

More information
For: – Latest firmware updates and latest compatible item list
– Any other latest information
Visit <www.kenwood.com/cs/ce/>.

Playable files

• Playable audio file for USB mass storage class device:
  MP3 (.mp3), WMA (.wma), WAV (.wav), FLAC (.flac)

• Playable USB device file system: FAT12, FAT16, FAT32
  Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or devices.

• For detailed information and notes about the playable audio files, visit <www.kenwood.com/cs/ce/audiofile/>.

About USB devices

• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
• This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1 A.

About iPod/iPhone

• Via USB input terminal:
  Made for
  – iPod touch (5th and 6th generation)
  – iPod nano (7th generation)
  – iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus, 8, 8 Plus, X

• It is not possible to browse video files on the “Videos” menu in [MODE OFF].

• The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone.

• You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.

• Depending on the version of the operating system of the iPod/iPhone, some functions may not operate on this unit.

About Android device

• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory (AOA) 2.0.
• If the Android device supports both mass storage class devices and AOA 2.0, this unit always playback via AOA 2.0 as a priority.

Muting upon the reception of a phone call
Connect the MUTE wire to your telephone using a commercial telephone accessory. (Page 18)

• When a call comes in, “CALL” appears. (The audio system pauses.)
  – To continue listening to the audio system during a call, press B SRC.
  “CALL” disappears and the audio system resumes.

• When the call ends, “CALL” disappears. (The audio system resumes.)

Change the display information
Each time you press DISP, the display information changes.

• If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information (eg. station name) appears or display will be blank.

For FM Radio Data System stations only:
Source name/Clock→ Station name/Program type → Radio text→
Radio text+→  Radio text+ song title/Radio text+ artist→  Frequency→
Clock→  back to the beginning
USB| For MP3/WMA/WAV/FLAC files:
Source name/Clock→  Song title/Artist→  Album title/Artist  Folder name
File name → Playing time  Clock → back to the beginning
iPod USB| (For KMM-205)
When [MODE OFF] is selected (page 8):
Source name/Clock  Song title/Artist  Album title/Artist  Playing time  Clock back to the beginning
ANDROID| Source name/Clock → Clock→  back to the beginning
AUX| Source name/Clock→  Clock → back to the beginning

Station name/Program type→  Radio text→  Radio text+  Radio text+→ song title/Radio text+→ artist  Frequency→  Date→  back to the beginning
USB| For MP3/WMA/WAV/FLAC files:
Song title/Artist→  Album title/Artist→  Folder name→  File name→  Playing time→  Date  back to the beginning
ANDROID| Source name→  Date → back to the beginning
AUX| Source name→  Date  →back to the beginning

TROUBLESHOOTING

•Check the cords and connections.
“MISWIRING CHECK WIRING THEN PWR ON” appears.| Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.
°PROTECTING SEND SERVICE” appears.| Send the unit to the nearest service center.
The source cannot be selected.| Check the [SOURCE SELECT] setting. (Page 5)
•Sound cannot be heard.
•The unit does not turn on.
•Information shown on the display is incorrect.| Clean the connectors. (Page 13)
The unit does not work at all.| Reset the unit. (Page 3)
Correct characters are not displayed.| •This unit can only display uppercase letters, numbers, and a limited number of symbols.
•Depending on the display language you have selected (page 5), some characters may not be displayed correctly.
Radio| •Radio reception is poor.
•Static noise while listening to the radio.| Connect the antenna firmly.
USB/i Pod| The playback order is not as intended.| The playback order is determined by the order in which file names were recorded (USB).
Elapsed playing time is not correct| This depends on the recording process earlier (USB).
°READING° keeps flashing.| •Do not use too many hierarchical levels and folders.
•Reattach the device (USB/iPod/iPhone).
The iPod/iPhone does not turn on or does not work.| •Check the connection between this unit and iPod/iPhone.
•Disconnect and reset the iPod/iPhone using a hard reset
Symptom| Remedy
---|---
USB/iPod| “LOADING” appears when you enter search mode by pressing | This unit is still preparing the iPod/iPhone music list It may take some time to load, try again later.
“NA FILE”| Make sure the media (USB) contain supported audio file (Page 13)
“COPY PRO”| A copy-protected file is played (USB).
“NO DEVICE”| Connect a device (USB), and change the source to USB again.
“NO MUSIC”| Connect a device (USB) that contains a playable audio file
“iPod ERROR”| •Reconnect the iPod.
•Reset the iPod.
ANDROID| •Sound cannot be heard during playback
•Sound output only from
the Android device.| •Reconnect the Android device.
•Launch any media player application on the Android device and start playback.
•Relaunch the current media player application or use another media player application.
•Restart the Android device.
•If this does not solve the problem, the connected Android device is unable to route the audio signal to uni (Page 13)
•If the USB connection does not work, connect the Android device through the auxiliary input jack.
“NO DEVICE” or “READING” keeps flashing.| •Reconnect the Android device.
•If the USB connection does not work, connect the Android device through the auxiliary input jack.
Playback is intermittent or sound skips.| Tum off the power saving mode on the Android device.
“NO MUSIC”/”ANDROID ERROR”| •Make sure the Android device contains playable audio files.
•Reconnect the Android device.
•Restart the Android device.

INSTALLATION/CONNECTION

Warning

• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect the Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
• To prevent short circuits:
  – Insulate unconnected wires with vinyl tape.
  – Be sure to ground this unit to the car’s chassis again after installation.
  – Secure the wires with cable clamps and wrap the vinyl tape around the wires that come into contact with metal parts to protect the wires.

Caution

• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in parallel.
• Mount the unit at an angle of less than 30°.
• If your vehicle wiring harness does not have the ignition terminal, connect the Ignition wire (red) to the terminal on the vehicle’s fuse box which provides a 12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat-dissipated metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching the car’s chassis, then replace the old fuse with one that has the same rating.

Part list for installation

Basic procedure

1. Remove the key from the ignition switch, then disconnect the terminal of the car battery.

2. Connect the wires properly.
   See “Wiring connection” on page 18.

3. Install the unit to your car.
   See “Installing the unit (in-dash mounting)” on page 17.

4. Connect the terminal of the car battery.

5. Press B SRC to turn on the power.

6. Detach the faceplate and reset the unit. (Page 3)

Installing the unit (in-dash mounting)

Removing the unit

1. Detach the faceplate.
2. Remove the trim plate.
3. Insert the extraction keys deeply into the slots on each side, then follow the arrows as shown in the illustration.

Connecting external components

Wiring connection

If your car does not have an ISO terminal:
We recommend installing the unit with a commercially available custom wiring harness specific to your car and leaving this job to professionals for your safety. Consult your car audio dealer.

A7
A8| Red
Black| : Ignition (ACC)
: Earth (ground) connection
B1
B2| Purple +
Purple/black –| : Rear speaker (right)
B3| Gray +| . Front speaker (right)
B4| Gray/black –
B5
B6| White +
White/Black –| : Front speaker (left)
B7| Green +| . Rear speaker (left)
B8| Green/black –

SPECIFICATIONS

MW
(AM)| Frequency Range| 531 kHz — 1 611 kHz (9 kHz step)
Usable Sensitivity (S/N = 20 dB)| 28.2 μV
LW
(AM)| Frequency Range| 153 kHz — 279 kHz (9 kHz step)
Usable Sensitivity (S/N = 20 dB)| 50.0 μV
USB| USB Standard| USB 1.1, USB 2.0 (Full speed)
File System| FAT12/16/32
Maximum Supply Current| DC 5 V  1 A
Frequency Response (±1 dB)| 20 Hz — 20 kHz
Signal-to-Noise Ratio (1 kHz)| 99 dB
Dynamic Range| 93 dB
Channel Separation| 89 dB
MP3 Decode| Compliant with MPEG-1/2 Audio Layer-3
WAV Decode| Linear-PCM
FLAC Decode| FLAC file (Up to 48 kHz/16 bit)
Auxiliary| Frequency Response (±3 dB)| 20 Hz — 20 kHz
---|---|---
Input Maximum Voltage| 1 000 mV
Input Impedance| 30 Id)
Audio| Maximum Output Power| 50W x4
Full Bandwidth Power
(at less than 1 96 THD)| 22 W x4
Speaker Impedance| 4 0 — 8 0
Tone Action| Bass| 100 Hz ±8 dB
Middle| 1 kHz ±8 dB
Treble| 12.5 kHz ±8 dB
Preout Level/Load (USB)| 2 500 mV/10 k0 load
Preout Impedance| s 600 0
General| Operating Voltage| 12 V DC car battery
Installation Size (W x H x D)| 182 mm x 53 mm x 100 mm
Net Weight (includes Template, Mounting Sleeve)| 0.6 kg

Subject to change without notice.

libFLAC
Copyright (C) 2000-2009 Josh Coalson
Copyright (C) 2011-2013 Xiph.Org Foundation
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions, and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,  INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance.
• Apple, iPhone, iPod, iPod nano, iPod touch, and Lightning are trademarks of Apple Inc., registered in the U.S. and other countries.
• Android is a trademark of Google LLC.

References

• Car Electronics Support Information | Kenwood
• Audio File | Kenwood
• EU/UK DoC Download | KENWOOD

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>