FINECO FX-36A Drone Quadcopter Instruction Manual
- June 5, 2024
- FINECO
Table of Contents
FINECO FX-36A Drone Quadcopter
PACKING LIST
- Quadcopter X1
- Instruction manual X1
- USB Charging wireX1
- Screwdriver X1
- Blade A X2
- Blade B X2
PREPARATION BEFORE FLIGHT
Charging Lithium Battery
Connect the USB cable with the drone lithium battery and the power supply,the
indicator light of the USB cable will be in red when charging and light off
when fully charged. The output of USB port should be SV±0.SV
The charging time is about 40 mins. If this product will not be used for a long period of time. please maintain 50% power for extending the operating life of the battery. Charged the battery as half normal fully charging time to keep it with 50% power.
Download Software
Use a smartphone to scan the QR code for software downloading, the “HK FLYER”
APP. It supports Android, Android(Google), and the 1OS system.
Turn on and turn off
Turn on steps
- Pull the power switch of the quadcopter to right, where shown” ON” . The LED light of the quadcopter will light on blue with the starting sound.
- Turn phone settings on, found “WAVE- Ble81y70E … ” in the Bluetooth list.
- Click it to link until it shows “v”, it was connected. If the smartphone can’t search the Bluetooth of the quadcopter, please turn off the quadcopter. Then re-turn on the quadcopter and re-search the Bluetooth again.
- Open the downloaded APP “HK FLYER” , enter the interface as below:
- After Bluetooth was connected, click the “Play” icon, enter the interface as below:
Shut Down Step
To shut down the quadcopter, pull the power switch to the end shown” OFF”
whenever
Control Menu Introduction
-
Exit control interface Click the icon to exit the control interface.
-
Light Control Switch Click this icon for turn on/off the LED light of the quadcopter.
-
Headless Mode Click this icon to turn on/off Headless Mode.
-
Gyroscope calibration Click this icon to turn on/off the gyroscope calibration function. It’s better to calibrate the gyroscope before the flight and please keep the quadcopter on the plane’s ground
-
Setting Height Mode This icon is setting height mode, open by default.
-
One key return Click this icon to start one key return function (under headless mode).
-
Flip Button Click this icon for the 360° flip function. In flipping mode, the quadcopter will fly to the direction according to AS A6 A7 AB.
-
Gravity Sensor Control Click this icon to enter/exit gravity sensor control mode, the quadcopter will fly as the gravity direction of the phone.
-
Speed Switch This quadcopter with three speeds, per click this icon one time to switch one speed, slow speed 30% / medium speed 60% / quick speed 100%.
-
One key landing Click this icon to start one key take-off function.
-
Click this icon to start one key landing function.
-
One key emergency stop suitable for any situation needs emergency stop.
-
Programming flight system Click this icon to enter the programming system. The following page appears
Click on the number table above in order to make the following action programming settings.
Select action and execution time then click “OK” to finish the programming. Exit the first action programming, and program other actions according to the same operation until the whole actions programming is finished.
When programming is finished, back
to the first programming interface, click the “START” button, the quadcopter
will fly as the programming actions. -
Trajectory Mode Click the icon then draw your flying route on the right side of the screen, the quadcopter will fly as the route.
-
Dancing Fly to the music Click this icon and choose the music, the quadcopter fly up and down as dancing according to the music till the end.
A 1 / A2 Ascend/Descend Pull left joystick to up / down, the quadcopter fly
up/down.
A3/A4 Turn left/right Pull the left joystick to left/ right, the quadcopter
turn left/ right.
AS/A6 Forward/ Backward Pull right joystick to up /d own, the quadcopter fly
forward / backward.
A7/A8 left/ Right Sideward Fly Pull the right joystick to left/ right, the
quadcopter fly to left side/ right side.
Flight Environment
Blades Installation
This quadcopter with different blades, every blade shown with “A” or “B”. Please install the blades to the correct position as shown in the right figure. Install blades wrong, the quadcopter could not take off, fly to one side or fly fall down.
FCC
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>