FOGATTI RV AC 115V Wall Mounted Control User Guide
- June 15, 2024
- Fogatti
Table of Contents
FOGATTI RV AC 115V Wall Mounted Control
Specifications
- Operating Modes: Dehumidify, Cooling, Heating
- Fan Speeds: Low, Medium, High
- Power Supply: 115VAC, 60Hz
- Control Buttons: On/Off, Mode Selection, Fan Speed Adjustment, Temperature Adjustment
- Communication: Wire controller
Product Usage Instructions
Operation
To operate the air conditioner, follow these steps:
- Press the On/Off button to switch on or switch off the machine.
- Press the Mode Selection button (M) to select the desired mode (cold, heat, blow, dehumidification).
- Press the Fan Speed Adjustment button to adjust the fan speed (high, middle, low).
- Press the Temperature Adjustment button to increase or decrease the set temperature point.
Fault Codes & Function Descriptions
If you encounter a fault condition, refer to the following table for
troubleshooting:
| Fault Condition | Digital Display Code | Solution |
|---|---|---|
| Communication interruption of relay control module | E1 | Check the dip switch. |
Check temperature sensor connection.
Replace temperature sensor if necessary.
Room temperature sensor is open or has different range| E2| Check temperature
sensor connection. Replace temperature sensor
if necessary.
Room temperature sensor fault| E3| Check temperature sensor connection.
Replace temperature sensor
if necessary.
Communication fault| C5| Check the wire between power and controller. Replace
PCB or
Controller if necessary.
Installation Instructions
To install the air conditioner, follow these steps:
- Remove the cover of the Wire controller box.
- Secure the back cover with screws.
- Refer to the provided drawing and install two screws one by one.
- Buckle the wire controller on the back cover to complete the installation.
Contact Information
If you have any further questions or need assistance, please contact us:
- Phone: 877-216-1818 (8:30am-5:00pm EST Monday-Friday)
- Email: us@fogatti.com
FAQ
-
Q: How do I switch on or switch off the air conditioner?
A: Press the On/Off button to switch on or switch off the machine. -
Q: How do I select the operating mode?
A: Press the Mode Selection button (M) to cycle through the available modes (cold, heat, blow, dehumidification). -
Q: How do I adjust the fan speed?
A: Press the Fan Speed Adjustment button to cycle through the available speeds (high, middle, low). -
Q: How do I adjust the set temperature?
A: Press the Temperature Adjustment button to increase or decrease the set temperature point.
The basic steps for operating the air conditioner are described in this user guide. For more detailed information about the operating mode and special functions, please refer to the operating instructions manual.
Operation
Quick reference to control buttons
- a. Press “ ” button switch on or switch off the machine.
- b. Press “ ” button select cold, heat, blow, dehumidification.
- c. Press “ ” button adjust the high or middle and low speed.
- d. Press “ ” button increase set temperature point. Press ” ” button decrease set temperature point. Temperature range: 16°C – 31°C/61°F – 88°F.
Mode Display
Fault code & Function descriptions
| Fault condition | Digital display code | Note |
|---|---|---|
| E1 | Communication interruption of relay control module | 1. Check the dip |
switch.
E2| Room temperature sensor is open or has different range| 1. check
temperature sensor connection.
2. Replace temperature sensor.
E3| Room temperature sensor fault| 1. check temperature sensor connection.
2. Replace temperature sensor.
C5| Communication fault| 1. Chek the wire between power and controller.
2. Replace PCB or Controller.
To difficult to change from °C to °F ?
Under the power-on state [ ] press and hold to switch ℃/℉
Installation Instructions
- Step One: Remove the cover of Wire controller box. Step Two: Secure the back cover with screws.
- Step Two: Secure the back cover with screws.
- Step Three: According to the drawing install two screws one by one.
- Step Four: Finally, the wire controller is buckled on the back cover and the installation is completed.
Remarks:
- After power-off and power-on or abnormal communication returns to normal, you need to re-operate the on-off button, or after setting the timing setting, or after waiting for three minutes, you can directly operate and adjust.
- The above pictures are for reference only, mainly in kind.
Wiring Diagrams
877-216-1818 (8:30am-5:00pm EST Monday-
Friday)
us@fogatti.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>