Schneider CCT595011 Wiser Motion Sensor Instruction Manual

: June 5, 2024
: Schneider

Table of Contents

Prerequisites
Additional system information
For your safety
Getting to know the product
Package contents
Choosing the mounting location
Mounting the sensor
Operating elements
Setting the sensor
The behavior of the status LED
Troubleshooting
Technical data
Schneider Electric Industries SAS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Wiser™
CCT595011

Schneider CCT595011 Wiser Motion Sensor - Fig2

Schneider CCT595011 Wiser Motion Sensor - Fig 4

Schneider CCT595011 Wiser Motion Sensor - Fig6

Schneider CCT595011 Wiser Motion Sensor - Fig8

Wiser Motion Sensor

Prerequisites

Download the Wiser app to your smartphone and install the Wiser Gateway/Hub (hereinafter referred to as Wiser Gateway) to configure and control Wiser devices.

Additional system information

Detailed product information is available online in the system user guide: Scan the QR code or follow the link.

https://www.productinfo.schneider-electric.com/wiser_eu/

For your safety

NOTICE

RISK OF DAMAGE TO DEVICE
Always operate the product in compliance with the specified technical data.
Failure to follow these instructions can result in equipment damage.

Getting to know the product

The Wiser Motion Sensor (hereinafter referred to as sensor) reports the detection of movement to the Wiser Gateway (and actuator to perform configured functions), measures the luminance of the environment, and passes this data to the Wiser Gateway. The threshold of luminance settings and/or detection of movement can be programmed to determine what action to be taken at that moment.
When the sensor is connected to the Wiser Gateway, it directly reports motion detection data to the Gateway.
When the battery is low (less than 10%), the status LED blinks orange once per minute, and a message is sent to the Wiser Gateway.

Package contents

A Motion sensor
B Baseplate
C Adhesive pad
D Screws: 2 × ST4.2 × 25 mm with wall plugs
E Installation instructions

Choosing the mounting location

The sensor can be mounted on a wall or ceiling to provide desired coverage:

The ceiling mount provides a 360° detection angle with a maximum range of 4 m diameter.
A wall mount provides a detection angle of 90° to 110° horizontal and vertical with a maximum range of 5 m radius.
Do not install the sensor in a place where there is strong sunlight or wind (for example, close to ventilation).
When the ambient temperature is >32°C, the sensor’s ability o measure sensitivity, detection range, and detection angle are degraded.

Walking direction
The PIR sensor is more sensitive to movement across different patterns. On the contrary, the sensor is less sensitive when movement is directed towards the sensor, since the range is reduced.
F More sensitive to movement across the pattern
G Less sensitive to movement directly towards the sensor

Mounting the sensor

Removing the battery isolation strip
Mounting

For wood or plastic surfaces, use either the adhesive pads or mounting screws.
If using screws, pre-drill a 1 mm hole.
For metal surfaces, use the adhesive pads only.

Operating elements

H Function key
I Sensor
J Status LED
K Base plate lock/unlock instruction:
Turn to lock into the base plate
Turn to unlock from a base plate
L Base plate

Setting the sensor

Remove the sensor from the base plate to access the function key H.
Connecting to the Wiser Gateway

1 Short press (< 0,5 s) the function key 3 times.
The sensor scans for the available Zigbee network. The status LED turns green if the sensor successfully connects to the Wiser Gateway.
2 Follow the instructions in the Wiser app to set the sensor parameters through the Wiser Gateway.

Resetting the sensor

Short press (< 0,5 s) the function key 3 times and then long-press the function key once for >10 s to reset the sensor to factory default mode.

All configuration data, user data, and network data are deleted.
Replacing the batteries
While refastening the battery cover make sure the triangle marks on the battery cover and the PCBA align.

The behavior of the status LED

Refer to the system user guide.

Troubleshooting

Refer to the system user guide.

Technical data

Battery	3 VDC, LRO3 MA x2
Battery life	Up to 5 years (may vary based on the usage, frequency of

Dispose of the device separately from household waste at an official collection point. Professional recycling protects people and the environment against potential negative effects.

Trademarks

Zigbee® is a registered trademark of the Zigbee Alliance.
Apple® and App Store ® are brand names or registered trademarks of Apple Inc.
Google Play ™ Store and Android ™are brand names or registered trademarks of Google Inc.
Wiser ™ is a trademark and the property of Schneider Electric SE, its subsidiaries, and affiliated companies.

Other brands and registered trademarks are properties of their relevant owners.

EU Declaration of conformity
Hereby, Schneider Electric Industries, declares that this product is in compliance with the essential requirements and other relevant provisions of RADIO EQUIPMENT DIRECTIVE 2014/53/EU. Declaration of conformity can be downloaded on: se.com/docs.