AMARYLLIS 21ARK-XKD Galaxy Nightlight Projector User Manual
- June 5, 2024
- AMARYLLIS
Table of Contents
AMARYLLIS 21ARK-XKD Galaxy Nightlight Projector
Unboxing Check
Thank you for purchasing our products, please read the instruction manual carefully before use. Instruction manual contains necessary safety advice and user instructions, follow the instruction manual to operate in order to avoid damaging the product for misuse. Check whether the product is damaged or not when you receive the product.
Pacakage list
- Galaxy Projector x 1
- Remote controller x 1
- USB cable x 1
- User manual x 1
Warnings
The power requirement of this product is USB DC 5V/2A. Once the range
exceeded, please use the regulator device, otherwise it’ ll affect its service
life.
Notice:
- Strictly in accordance with the instructions of this operation, do not disassemble the host and accessories.
- This product is suitable for indoor use.
- The product is projected by LED and laser combinations, please do not use laser shone directly in eyes and keep away from children.
How to use:
- Indoor use, projecting in the sky direction.
- How to use the light projector, as shown below.
- Connect Bluetooth “BTK10” of the smart phone to play music.
- Use correct method of the remote control to make sure the remote control is pointing at the infrared sensor.
Host button function description
- Automatic recognition of USB data. Note that this projector can auto recognize and play music while inserting USB memory. USB should contain some songs
- Ocean wave 3 levels brightness adjustment When power on, LED light and laser light keep on; short press this key control LED light switch, long press control laser light switch
- DC Input: 5V/2A.
- The short press plays the previous song; Long press reduces the volume
- Short press plays next song; Long press increase the volume
- Short press control music Play/pause; Long press change USB to Bluetooth ( Connect Bluetooth and U-Disk at same time, it’ll recognize U-Disk music for priority)
- Short press achieves Bluetooth/USB mode switch when connecting Bluetooth and USB at same time
- Power ON/OFF
Statement
This product has been comprehensive and rigorous tasted at the factory, the
user should strictly follow the warning and instructions. Improper use
resulting in product damage is not covered by the Company’s warranty.
Remote control function description
Instruction:
When projector light connects power; LED blue light keeps on and in non-moved
status; laser light enters gradation mode; it can default automatically switch
off in 4 hours.
-
Control LED ocean wave light ON/OFF
-
Control Laser light ON/OFF
-
Press “R”, red light ON; Press again, red light OFF (at basic of light on at the first time)
-
Press “G”, green light ON; Press again, green light OFF (at basic of light on at the first time)
-
Press “B”, blue light ON; Press again, blue light OFF (at basic of light on at the first time)
-
Press “W”, white light ON; Press again, white light OFF (at basic of light on at the first time)
(Note: Four-color RGBW buttons can be combined by two to form a double-color projection) -
Control device volume up
-
Control device volume down
-
Select playing the previous song
-
Select playing the next song
-
Voice control: Connect with Bluetooth or USB memory to play music, press “Micro” icon, ocean waves and star light will fast-changing following music sound
-
Control ocean wave moving speed up (pause–Slow–Medium–Fast)
-
Control ocean wave moving speed down (Fast–Medium–Slow–Pause)
-
Long press 3 seconds to cancel timing function. When LED, laser light flashes and emit a “bleep” sound three times as prompting
-
Press “FADE 1”, ocean wave moves circularly in R-G-B-W single color mode and laser light changes to gradation mode (the same feature as power on)
-
Press “FADE 2”, ocean wave moves circularly in RB-RG-RW-BG-BW-GW double-color mode and laser light changes to gradation mode
-
Long press 3s control timing function for 1 hour. When LED, laser light flashes and emit a “bleep” sound once time as prompting. 1 hour later, it’ll automatically switch off.
-
Control LED ocean wave light brightness (In order of 70%–40%–40%–70%–100%)
-
Press “LASER light” to achieve either Laser light stay on or entering into gradation mode
-
Long press 3s control timing function for 2 hours. When LED, laser light flash and emit “bleep” sound 2 times as prompting. 2 hours later, it’ ll automatically switch off
-
Control Music Switch On/Off
Notice:
This product comes with 4 hours automatically shut down function that works
for 4 hours and shut down automatically.
Specification
- Maximum LED Power: 2 * 4W
- Green Laser: < 1MW
- Power Input: USB DC5V / 2000mA
- Operating Temperature: 14 F 104 F (-10 C 40 C)
- Projection Coverage: 161 538 ft (15 50m )2
- Product Dimensions: 123 * 164 mm
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The distance between user and products should be no less than 20cm
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. The
distance between user and products should be no less than 20cm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>