ILIFE Shinebot W400s Floor Washing Robot User Guide

: June 5, 2024
: iLIFE

Table of Contents

ILIFE Shinebot W400s Floor Washing Robot
Important Safety Instructions
Important Tips
How to perform the best
In the Box
Product Anatomy
Installation
Install the main brush
Start Cleaning
Maintenance
Clean the dirty water tank
Troubleshooting
Product Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ILIFE Shinebot W400s Floor Washing Robot

Thank you for choosing Shinebot W400s Floor Washing Robot! You’ve joined millions of people to get the Thank you for choosing Shinebot W400s Floor Washing Robot! You’ve joined millions of people to get cleaning done robotically.
This user manual helps you to keep your robot performing at its best. Please take a few moments to read through it.

Get model-specific customer support, including Q&A, maintenance tips, demo videos, live chat and more;
Get the most recent product updates including new product launches, exclusive discounts and special promotions.

You may find us on: Facebook: https://www.facebook.com/iliferobotics
Twitter: twitter.com/lLIFEROBOTICS If you have any questions, please contact our customer service for assistance or visit www.iliferobot.com for more information. Enjoy automated home cleaning performed by Shinebot W400s.

Important Safety Instructions

Read all instructions before using this appliance.

Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
Do not use outdoors.
Do not allow device to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer’s recommended attachments.
working as Do it not should, use or with it has damaged been power dropped, cord or damaged, plug. If left appliance outdoors, is or not dropped into water, return it to a service center.
Do not pull or carry by power cord, use power cord as a handle, close a door on power cord, or pull power cord around sharp edges or corners. Do not run appliance over power cord. Keep power cord away from heated surfaces.
Do not unplug by pulling on power cord. To unplug, grasp the plug, not the power cord.
Do not handle plug or appliance with wet hands.
Do not put any objects into openings. Keep free of dust, lint, hair and anything that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Turn off all controls before unplugging.
Do not use the robot to wash flammable or combustible liquids, such as gasoline, or use in areas where they may be present.

CAUTION
To reduce the risk of injury from moving parts, unplug before servicing.

Do not allow robot to clean anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Do not use without water tank in place.
Always insert batteries correctly with regard to polarity(+ and – ) marked on the battery and the product.
Exhausted batteries should be immediately removed from product and properly disposed of.

Intended use

This product is intended for household use only. It is not intended for commercial use.
This product is intended to work in environments between 10°C and 50°C.

Tips and tricks

Stop the appliance promptly if error occurs during cleaning. Before using the appliance, remove all power cords and small objects from on the floor.
Roll up carpet tassels and make sure that curtains and tablecloths are not in contact with the floor.
If there are any raised floors such as steps or stairs, test if the appliance can detect the height difference to prevent it from falling.
Do not allow hair, clothes or fingers near openings or mechanical parts of the appliance.
Do not put any objects in the main brush holder. To ensure smooth rotation of the main brush, remove dust, batting and any hair from around it.

Important Tips

How to start

Turn on/off
To turn the robot on, press for ls. To turn it off, press for 3s. Release the button after a sound alert.
Pause/Resume
To pause the robot, press. while it’s cleaning. Press. again to resume the cleaning cycle.

Clean
Install the main brush before use. Fill the clean water tank with clean water and DO NOT add any detergents.

How to perform the best

Fill up the clean water tank before each use for better performance.
Choose the Spot mode for areas with stubborn stains.
Empty the dirty water tank after each use, and clean the water tank outlets and inlets regularly.
Remove the main brush and rinse with water once a week.
Clean both vents and remove the dust and debris regularly.
The robot is skilled at cleaning up different types of stains, like milk, ketchup, coffee and footprints.
The robot performs well on tile floor with small gap
The robot does not work properly on tile floors with gaps wider than 10mm
The between robot tiles does is not higher work than properly 3mm. on tile floors if the height difference between tiles is higher than 3mm.
The (more robot than does 2mm not in work height). properly on uneven tile floors more than 2mm in hight.
don’t use the robot on the upper floor if there is a risk of it falling down.

In the Box

Product Anatomy

Main body

Display panel

Host machine

Remote control

Up/Down/Left/Right
Direction can only be changed when the robot is on standby. Long press A. to activate the robot and move it forward. The robot will follow the direction that the remote control points at and start cleaning.

Charging dock

Installation

Install the charging dock Shinebot W400s is not a self-charging robot. Please take it to the dock manually for recharging after each use.
Step 1

Turn the charging dock upside down
Plugin the power cord.
Secure wires around the cable channel.

Step 2
Put the charging dock somewhere level, dry and safe, and manually take the robot back to the charging dock to recharge. Voice alert: Charging will start soon.

Battery condition
Please check icon on the display panel if needed, and recharge if it goes low.

Install the main brush

It’s recommended to properly dampen the main brush before installation for better cleaning performance.

Insert the recessed end of the main brush into the gearwheel.
Press down on the capped end into the other end of the main body.

Install the water tank

Step 1. Fill the water tank

Press down on the water tank release button, pull the handle up to detach the tank.
Turn the integrated water tank upside down.
Open the clean water tank cap and fill up the tank with clean water.

Step2. Install the water tank

Align the bottom of the integrated water tank with the main body and push forward.
Align the ends and move the water tank to insert it into the main body.
Press down, and a “click” will be heard if installed properly.

Start Cleaning

Place the robot
Take the robot out of the charging dock to the cleaning starting spot, and place the robot at least 1.6 ft away from the wall.

Select cleaning mode

the robot has 4 cleaning modes. Choose the mode you need by pressing the MODE button on the display panel or corresponding buttons on the remote control.
Press the button to start cleaning.
- Tap the MODE button to switch cleaning modes.
- Press the button on the remote control to switch modes directly.

The robot will continue to clean using the last used cleaning mode if no new command is received.

Area mode

The robot cleans only the area ahead of its starting point within 270 sq.ft. This mode is intended to avoid the areas you don’t want cleaned.

Path mode

For large space cleaning. The robot cleans in a methodical path from the starting spot. After the cleaning cycle, the robot will return to the starting spot.

Spot mode

The robot automatically increases suction power and water flow to clean stubborn stains. It cleans at a square spiral route from the starting point, and it will take the same route back to the starting spot after two rounds of cleaning.

Edge mode

On the Edge mode, the robot will automatically detect and clean along edges and around corners.
Note:
Before starting Edge mode, put the robot near the walls and! remove the obstacles nearby, such as chairs, tables, etc.

Maintenance

To keep the robot running at peak performance, you are advised to perform the following maintenance regularly:

Please install water tank correctly

| ****

: Red

CLEAN: Red

i: Orange

| Water tank isn’t installed or properly installed.| ****

Ensure the water tank is installed properly.

Please fill the clean water tank| ****

Water tank is empty or clogged.

| • Fill with clean water

• Check the clean water inlet.

Please empty the dirty water tank| ****

Dirty water tank is full.

| ****

Empty the dirty water tank.

Please place the robot to an open area| ****

CLEAN: Red

i: Orange

| ****

Robot is stuck in a narrow space.

| Put the robot in an open area and start cleaning again.

Please check the main brush

| ****

Main brush is jammed.

| • Check if the main brush is jammed because of an object.

• Clean both ends of the main brush.

Please check and clean the universal wheel| ****

Nose wheel is stuck.

| Check if the wheel is jammed by debris or hair. Remove the wheel and clean it.
Please check and clean the cliff sensor| ****

Drop sensors are contaminated.

| ****

Check and clean the drop sensors.

Please put robot back to ground| ****

Robot isn’t on a flat surfa ce.

| ****

Put the robot on a flat floor.

Low battery, please charge| ****

_,:Red

| ****

Battery is low.

| ****

Recharge the robot.

Clean the dirty water tank

Detach the integrated water tank.
Open the cap and empty the waste.
Fill the dirty water tank with clean water. Close the cap and shake.
Open the cap again and empty the tank.

Clean the main brush

Remove the integrated water tank and take out the main brush, then rinse with clean water .

Detach the integrated water tank.
Remove the main brush from the robot body.
Remove all the debris on the main brush.
Rinse the main brush with 0 Rinse the main brush with clean water, and air dry it before reinstallation.

Clean the filter

Remove the filter from the water tank and rinse with water.

Clean the water tank openings

After removing the filter, press the water tank lock button to open the fan-coil outlet. To maintain the water tank’s proper functioning, clean both openings of the fan-coil outlet and remove dust and debris.
To keep the tanks tightly sealed, clean the inlet and outlet, and the caps of both tanks regularly.

Clean the nose wheel

Turn the robot upside down and check if the castors can rotate smoothly. Remove the nose wheel by pulling it out vertically. Check if there is any hair or debris stuck on it.