ILIFE W450 Shinebot Floor Washing Robot User Guide

ILIFE W450 Shinebot Floor Washing Robot

Thank you for choosing Shinebot W450 Floor Washing Robot! You’ve joined millions of people to get cleaning done robotically.
This user manual helps you to keep your robot performing at its best. Please take a few moments to read through it.
You may also connect with us on Facebook and Twitter to enjoy exclusive benefits:

• Get model-specific customer support, including Q&A, maintenance tips, demo videos, live chat and more;
• Get the most recent product updates including new product launches, exclusive discounts and special promotions.

You may find us on:

• Facebook: facebook.com/iliferobotics
• Twitter: twitter.com/lLIFEROBOTUS
• If you have any questions, please contact our customer service for assistance or visit www.iliferobot.com for more information.
• Enjoy automated home cleaning performed by Shinebot W450.

I LI FE Customer Service
1-80Mon-Fn. 9.00A.M. 31-9676- _ (Toll 5.00P.M.CST free for USA & Canada) @ support@iliferobot.com

Important Safety Instructions

• Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
• Do not use outdoors.
• Do not allow device to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• working as Do it not should, use or with it has damaged been power dropped, cord or damaged, plug. If left appliance outdoors, is or not dropped into water, return it to a service center.
• Do not pull or carry by power cord, use power cord as a handle, close a door on power cord, or pull power cord around sharp edges or corners. Do not run appliance over power cord. Keep power cord away from heated surfaces.
• Do not unplug by pulling on power cord. To unplug, grasp the plug, not the power cord.
• Do not handle plug or appliance with wet hands.
• Do not put any objects into openings. Keep free of dust, lint, hair and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Do not use the robot to wash flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
• Do not allow robot to clean anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without water tank in place.
• Always insert batteries correctly with regard to polarity(+ and – ) marked on the battery and the product.
• Exhausted batteries should be immediately removed from product and properly disposed of.

Intended use

• This product is intended for household use only. It is not intended for commercial use.
• This product is intended to work in environment between -10°C and 50°C.

Tips and tricks

• Stop the appliance promptly if error occurs during cleaning. Before using the appliance, remove all power cords and small objects from on the floor.
• Roll up carpet tassels and make sure that curtains and tablecloths are not in contact with the floor.
• If there are any raised floors such as steps or stairs, test if the appliance can detect the height difference to prevent it from falling.
• Do not allow hair, clothes or fingers near openings or mechanical parts of the appliance.
• Do not put any objects in the roller brush holder. To ensure smooth rotation of the roller brush, remove dust, batting and any hair from around it.

Important Tips

A Shinebot W450 contains electronic parts. DO NOT immerse the !

How to start

• Turn on/off
  To turn the robot on, press m for 0.5s. To turn it off, press m for 3s. Release the button after a sound alert.

• The robot will automatically enter sleep mode if no command is

Pause/Resume
To pause the robot, press while it’s cleaning. Press again to resume
the deaning cycle.
Clean
Install the main brush before use. Fill the clean water tank with clea water.

How to perform the best

• Fill up the clean water tank before each use for better performance.
• Choose the Spot mode for areas with stubborn stains.
• Empty the dirty water tank after each use, and clean the water tank outlets and inlets regularly.
• Remove the main brush and rinse with water once a week.
• Clean both vents and remove the dust and debris regularly.
• The robot is skilled at cleaning up different types of stains, like milk,
• ketchup, coffee and footprints.

Important Tips

• The robot workS on a variety of hard floor surfaces, Such as porcelain tiles, vinyl flooring, and laminated floors.
• The robot performs well on tile floor with small gaps.
• The robot does not work properly on tile floors with gaps wider than 10mm.
• The robot does not work properly on tile floors if the height difference between tiles is higher than 3mm.
• The robot does not work properly on uneven tile floors (more than 2mm in height).
• Don’t use the robot on the upper floor if there is a risk of it falling down.
• Don’t use the robot on stairs to reduce the risk of it falling down.

In the Box

• Robot main body  (include a main brush)

• Charging dock

• Adapter

• Main brush

• Cleaning tool
  Hard floor cleanser

• Remote control

• User guide

• AAA battery (X2)

Product Anatomy **

**

Display panel

Product Anatomy

Host machine

Product Anatomy

**Product Anatomy

**

Up/Down/Left/Right Direction can only be changed when the robot is on standby.

Charging dock

Product Anatomy

Indicator

Installation

Install the charging dock
Shinebot W450 is not a self-charging robot. Please take it to the dock manually for recharging after each use.
Step 1

1. Turn the charging dock
2. Plug in the power cord.
3. Secure wires around the cable channel.

Step 2
Put the charging dock somewhere level, dry and safe, and manually take the robot back to the charging dock to recharge.

Voice alert: Start Charging!

1. Put charging dock and the robot in right direction.
2. Take the robot back to charging dock.

Battery condition

• If the light on is orange, it means the battery is low. Please charge it immediately.

Install the main brush

• It’s recommended to properly dampen the main brush ‘! before installation for better cleaning performance. !
  1. Insert the recessed end of the main brush into the gearwheel.
  2. Press down on the capped end into the other end of the main body.

Add water and cleanser

1. Press down on the water tank release button, and pull the handle up to detach the tank. Turn the integrated water tank upside down.

2. Open the clean water tank cap and fill up the tank with clean water.

3. and to ensure that the water
   After volume filling exceeds up the water, minimum erect the water level.t

4. Add the specific Shinebot cleanser (if necessary).

Note

1. Do not use distilled or purified water.
2. Do not add any detergents except Shinebot cleanser.

Installation

Instructions
Cleanser to water dilution ratio is 1:100. Add a bottle cap of cleanser in the clean water tank before each cleaning.
( Attention: Using excessive cleanser can damage the Shinebot, which i should be avoided.

The Shinebot Hard Floor Cleanser
This concentrated cleanser is available to all kinds of hard floors that are sealed well.

Install the water tank

1. Align the bottom of the integrated water tank with the main body and posh forward
2. Align the ends and move the water tank to insert it into the main body.
3. Press down, and a “click” will be heard if installed properly.

Start Cleaning

Select cleaning mode

Press button or use the remote control/APP to change cleaning modes when the robot is in standby. Then press button to start cleaning your home.

1. Tap the button to switch cleaning modes.
2. Press button on the remote control to switch modes directly.

The remote control can only be used when the robot is turned on.

Standby mode

1. Pres button to choose the cleaning mode. Press button 3s to connect the robot to Wi-Fi.
2. Press the button to start cleaning, and press the button again for 3s to turn the robot off.
3. The robot will go to SLEEP mode if no command is received in 20mins.

The above can only be operated in standby mode.

Area mode

• Recommended to clean a specific area. The robot will clean the area ahead of its starting point at the zigzag path. It will return to the starting point when the cleaning is finished. Press the button to pause the robot.
  (The below right picture shows the cleaning path of area mode, subject to the actual situation.)

• Recommended to clean large area. The robot cleans in zigzag path and return to the starting point when cleaning finished automatically. Press button to pause the robot.
  (The below right picture shows the cleaning path of path mode, subject to the actual situation. )

• Spot mode
  Recommended to clean a localized area with heavy stains. The robot cleans in “spiral” path and return to the starting point and goes into standby mode when cleaning finished automatically.
  (The below right picture shows the cleaning path of Spot mode, subject to the actual situation.)

Place the robot

• Select cleaning mode and press button start cleaning. For better cleaning efficiency, please place the robot stably against walls and keep 0.5m away from any obstacles.
• Press button again to stop the robot from cleaning.
• The robot will work out the best cleaning path when running. If the robot is moved manually or by remote control, it gets disrupted and will work out a new cleaning path. In order to improve cleaning efficiency and reduce repeated cleaning, please do not move the robot when it’s cleaning.

Attention

1. The robot will return to the starting point when clean water runs out or the dirty water tank is full. Users should refill the clean water or empty the dirty water according to its voice prompts. Put the robot to the place where it stops cleaning and press the clean button to continue the work.
2. Please empty the dirty water tank after each cleaning, as well as cleaning up and maintaining the robot.

APP Download

Downloading the APP
The robot can be controlled by the “ILIFEHOME” app. Scan the QR code to install the app on your iOS or Android device.

Maintenance

• To keep the robot running at peak performance, you are advised to perform the following maintenance regularly:

Clean the dirty water tank

1. Detach the integrated water tank.
2. Open the cap and empty the waste.
3. Fill the dirty water tank with clean water. Close the cap and shake.
4. Open the cap again and empty the tank.

Clean the main brush and scraper

• Remove the integrated water tank and take out the main brush, then rinse with clean water.

1. Detach the integrated water tank.
2. Remove the main brush from the robot body.
3. Remove all the debris on the main brush.
4. Rinse the main brush with clean water, and air dry it before reinstallation.

The scraper is screwed to the robot. Please do not try to disassemble it and rinse it after each running.

1. The scraper is fastened by the screws, which is not recommended to be detached. Please kindly rinse the scraper under the faucet.
2. In order to keep the cleaning efficiency of the scraper, please place the robot correctly on the charging dock after cleaning or machine maintaining. Otherwise, the severe squeezing of the scraper will affect the cleaning efficiency (as shown in the figure below).

Clean the filter

• Remove the filter from the water tank and rinse with water.

Clean the water tank openings

After removing the filter, press the water tank lock button to open the fan- coil outlet. To maintain the water tank’s proper functioning, clean both openings of the fan-coil outlet and remove dust and debris.

• To keep the tanks tightly sealed, clean the inlet and outlet, and the caps of both tanks regularly.

Clean the metal pins on the dirty water tank/ main body/ charging dock

• Wipe the the metal pins on the dirty water tank /main body/ charging dock regularly with dry clean cloth.

Clean the nose wheel

• Turn the robot upside down and check if the nose wheel can rotate smoothly. Remove the nose wheel by pulling it out vertically. Check if there is any hair or debris stuck on it.
  1. Turn the robot upside down.
  2. Pull the nose wheel out vertically.
  3. Check if there is any hair or debris stuck on it.

Note:  After maintenance, reinstall all components and place the robot !
! on the charging dock. Always store the robot in a safe environment

Troubleshooting

Voice Alerts

Others

Product Specifications

ILIFE Customer Service
1-800-631-9676
(Toll free for USA & Canada) Mon-Fri: 9:00AM. – 5:00P.M.CST
support@iliferobot.com

Documents / Resources

| ILIFE W450 Shinebot Floor Washing Robot [pdf] User Guide
W450, Shinebot Floor Washing Robot, Shinebot Floor Washing, Floor Washing, Washing Robot
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>