BEB Electronics BEBQ020 Wireless Charger User Manual
- June 5, 2024
- BEB Electronics
Table of Contents
BEB Electronics BEBQ020 Wireless Charger
Thank you for embracing the future of wireless charging technology. With our sleek and stylish wireless charger, you can charge your compatible Qi-enabled device, without the need to attach a charging cable or the need to plug your device into a wall charger or USB port. Starts charging the moment you place down any Qi-enabled device. And, you can still use your device while charging to make and answer calls without having to unplug. Please read all instructions and safety information prior to using the wireless charger as improper use of this item may result in product damage, excessive heat, toxic fumes, fire or explosion. Please keep the User Manual for future reference.
Instructions
- Connect the Micro USB interface to the wireless charger.
- Connect the USB 2.0 interface to a power adapter or USB charging port.
- Connect to power source: LED light brightness for 2 seconds.
- Stand-by status: No LED light brightness .
- Charging: LED steady light brightness.
- Includes: Wireless charging pad, Micro-USB Charging cable, User manual.
Specification
- Input: 9V 1.67A/5V 2A
- Output: 9V 1.1A/5V 1A
- Charging efficiency: 60-70%
- Charging distance: 3-l0MM
- Frequency: 110-205KHz
- Wireless charging Power: 10W
- Wireless standard: Qi
Applicable Devices
Devices with Qi built-in wireless charging receiver
Safety Information
- The charging pad will get warm. This is normal with induction charging.
- Do not use your device for 1 minute if the device becomes overheated.
- Prolonged exposure of your skin to an overheated device may cause low temperature burn symptoms, such as red spots and pigmentation.
- Do not store your device near or in heaters, microwaves, hot cooking equipment or, high pressure containers as your device may overheat and cause a fire.
- Do not drop or cause impact to the charger.
- Store your device only on flat surfaces.
- If children use the device, make sure that they use the device properly.
- Keep your device dry and away from moisture.
- Humidity and liquids may damage the electronic circuits in your device.
- o not wash the device with any chemicals, soaps or detergents.
- Do not disassemble, modify, or try to repair your device as you risk electric shock.
- Do not place too close to a credit cards with magnetic strip or chip card to avoid magnetic failure.
- Please keep a distance of at least 20cm between implantable medical devices and the wireless charger, to avoid potential interference with the medical device.
- Working Environment temperature 0-S0°C / 32-122° F
- To turn this apparatus off completely, you must disconnect the cable from the device or disconnect from the power source.
- To enable optimal wireless charging, it is recommended to remove phone cases.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>