Jacassi JY2101-RF LED Solar PIR Motion Sensor Light User Manual

USER MANUAL
LED SOLAR PIR MOTION SENSOR LIGHT
MODEL: JY2101-RT

Please read the user manual carefully before use

Introduction

Thank you for purchasing the solar PIR motion sensor light. We hope you enjoy our solar lighting solution. To ensure the proper operation of this solar light, please read this user manual carefully and keep it for future reference.

Package Includes

| 1X Solar PIR Motion Sensor Light
---|---
1X Remote Control
1X User Manual
4 X Installing Screws
4 x Expansion Pillar-hinge

Specifications

Product Features

Easy to install and uses energy-saving solar technology.
Widely used for illumination in gardens, garages, and other places exposed to sunlight.
Fully automated operation. Automatically turns off during the day and automatically lights up when it senses movement at night.

Remarks
This is a solar energy product, please choose a location that receives adequate sunshine to ensure effective charging during the day. The longer it gets sunshine the longer it can illuminate.

We recommend a mounting height of 1.8-2.2 meters.
Lighting Modes:

1. OFF
2. ON

The Remote Control Functions:

ON/OFF
Mode1: Sensor mode
Automatically turns off during the day and will only turn on when it senses movement at night. The light will turn off after 30 seconds of no movement. If people stay active in the sensor area the bright light mode will remain on.
Mode2: Always ON
It will automatically turn on at night and stay dimly all night with or without detecting motion. And then it will automatically turn off at dawn.

Mode3: Sensor mode+Dim
Automatically turns off during the daytime and will turn on dim light at night. When it senses people’s movement at night, the light will turn on to brightness and turn to dim light after 30 seconds.
“-“ Mode: There are 5 modes to lower the brightness.
“+” Mode: There are 5 modes to brighten the brightness.

Installation

1. Press the button switch to turn on the light
2. Fix the pillar hinge into the wall
3. Place the screw hole of the lamp over the pillar hinge
4. Put a screw through the lamp and twist it into the pillar hinge
5. The installation is completed

Note

1. The internal light sensor ensures the movement sensor will not activate during the day. When the ambient light becomes dark the sensor will activate.
2. The product is equipped with an internal lithium battery, please do not replace it by yourself, put it with household garbage, or place it near sources of heat. It should be taken to your local battery disposal center.
3. A full charge requires up to 8 hours of sunlight. Mounting location, weather conditions, and seasonal variation will directly influence the actual run time experienced.

Product Warranty

We provide our lamp with a 12-month limited warranty from the date of purchase. To make a warranty claim please contact the retailer you purchased this light from.
Warranty Limitations:
The following are not covered by our warranty:

1. Purchases from non-authorized sellers or distributors.
2. Damage resulting from fire, moisture, improper use, physical shock, or other damage occurring after purchasing the lamp.
3.  If the item has been dismantled or modified after purchase.

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>