Huabo HB2022N Drone Air Racer Instruction Manual
- June 5, 2024
- Huabo
Table of Contents
HB2022N Drone Air Racer
Instruction Manual
Getting to Know Your Drone
PLEASE READ ALL WARNINGS AND INSTRUCTIONS PRIOR TO USE. KEEP THIS DOCUMENT AS
IT CONTAINS IMPORTANT INFORMATION ABOUT YOUR DRONE.
1. PREPARE FOR FLIGHT
- The drone must be charged before each use (Cable included).
- The indicator light will turn off once fully charged.
- Install batteries in the remote.
2. PAIR YOUR DRONE
Before each flight pair the remote with the drone:
- Turn your drone on and place it on a flat, level surface.
- Turn on the remote and move the left joystick up, then down.
- The beep will indicate successful pairing.
- Repeat steps 1 and 2 if necessary.
3. REMOTE CONTROL OVERVIEW
Practice flying your drone below 10 feet and at low speeds until comfortable
with all controls to avoid unnecessary damage or injury.
- Left joystick: left/right controls spin and Up/Down controls elevation.
- Right joystick: controls flight direction.
- Direction Trim: use to eliminate drift.
To cut power to the drone, move the left joystick to the down position.
QUESTIONS OR CONCERNS?
PLEASE GIVE US A CALL … WE’RE HERE TO HELP
CUSTOMER SUPPORT
800-374-2744
Before calling please locate the 10-digit code printed on the back of your
remote
ADULT ASSEMBLY, CHARGING, AND BATTERY INSTALLATION ARE REQUIRED. ADULT
SUPERVISION IS REQUIRED.
Sharper Image®’s name and logo are registered trademarks. Distributed by and ©
2022 MerchSource, LLC. Irvine, CA 92618. All rights reserved. Distributed by
MerchSource, LLC, Irvine, CA 92618.
For technical support, please visit
www.merchsource.com or call
1-800-374-2744.
The artwork and design of this manual are protected by US copyright law and
may not be reproduced, distributed, displayed, published, or used for any
purpose without prior written permission. It is not permitted to alter, remove
or reproduce any trademarks or copyright notice from this manual.
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION FOR
FUTURE REFERENCE.
Due to continuous product improvements, the picture on the manual may differ
slightly from the actual product.
PATENT PENDING
INTRODUCTION
Congratulations on your purchase of the Rechargeable 2.4 GHz Fly+Drive Drone. Get ready to soar to new heights. Master the art of drone flying with remote control maneuverability. This lightweight drone will provide hours of fun.
SPECIFICATIONS
Drone Battery: 800 mAh Li-po
Remote Controller Battery: 4 x 1.5V “AA”
Charging Time: 120 minutes
Maximum Recommended Altitude: 100 ft.
READ ALL WARNINGS AND PRECAUTIONS BEFORE USE
SAFETY WARNINGS
- Not recommended for children under 14 years of age. As with all electrical products, precautions should be observed during handling and use to reduce the risk of electrical shock.
- Adult supervision is required at all times.
- Drive drone only on smooth flat surfaces.
- Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.
- Always use caution when flying drone vehicles, obey relevant laws, and respect the privacy and property rights of others.
- The drone shall never be modified or used for anything except its intended purpose.
- Before each use, an adult should review the product and battery to determine that no damage or hazards exist.
- DO NOT TOUCH SPINNING PROPELLERS.
- Do not allow anything to intentionally make contact in any way with spinning propellers o Prevent contact with spinning blades by turning off the remote prior to handling the drone.
- Use caution and pay attention to your surroundings while operating a drone.
- Do not fly drones into animals, people, or inanimate objects.
- Keep drones away from power lines, buildings, trees, public areas, and any other potentially hazardous areas.
- Do not operate in rain, heavy wind, or any type of severe weather.
- Do not land drones on wet surfaces.
- Never touch or allow others to touch the drone while it is flying.
- Always turn the drone off when it is not in use.
- Always fly drones in large open areas.
- The drone will lose controlling capabilities if the fly distance is more than the maximum recommended altitude of 100 ft. Keep below 100 ft. to avoid potential crashing risk.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Fly-aways are the responsibility of the individual pilot and will not
be replaced by the manufacturer.
This drone weighs 0.242lbs (110g). As of December 21, 2015, the Federal
Aviation Administration (FAA) only requires registration on unmanned aircraft
weighing more than .55 lbs. Visit
www.faa.gov/uas/registration/ for more
information. Although the FAA does not require this drone to be registered,
ongoing compliance with federal, state, and local laws is the owner’s sole
responsibility. Always fly safely and respect the privacy of others.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
TROUBLESHOOTING:
When the remote switch is turned on, the remote light does not illuminate:
- Check that battery in the remote is installed correctly OR
- Replace with new batteries.
When remote LED comes dim or the control sensitivity is weak:
- Remote batteries are low.
- Replace them with new batteries.
Drone and remote properly pair, but the drone will not lift off or the drone LEDs flash during the flying:
- Drone Li-Po needs charging.
- Use a charging cable to connect the drone to a power source.
After trimming the drone, the drone flight is very unstable and cannot fly properly:
- One or more blades are most likely damaged.
- Turn off the drone and remote.
- Replace with the proper number of replacement blades and try flying again.
After impact, the drone is unstable:
-
Land the drone on the ground and the propellers are stopped.
Press and hold the Land button for 3s to calibrate the gyro. -
If the above does not resolve the issue, reboot the drone and controller and pair again.
Remote Controller and Drone can not be paired:
- CheckPoint: Remote Controller must be close to Drone.
- Do not exceed 4 meters.
Note: If there are 2 sets of Drones within 4 meters for Pairing, you must pair one successfully before pairing the second set.
CONTENTS
REMOTE BATTERY INFORMATION
- Unscrew the remote battery door using a Philips head screwdriver (not included).
- Install 4 “AA” batteries as shown in the diagram above.
- Replace and close the battery compartment.
LITHIUM-POLYMER BATTERY WARNING
There is a risk of fire and personal injury if the Li-Po battery is punctured,
damaged, or misused.
- Never expose the battery to extreme temperatures or moisture.
- Do not subject the battery to strong impacts.
- Always keep the battery away from flammable materials.
- Only use manufacturer-specified batter(ies), charger(s), and/or adapters, if applicable.
- The battery is not serviceable.
- Let the battery cool to room temperature before charging.
- While charging, never leave the battery unattended.
- Recycle or dispose of batteries according to federal, state, and local laws.
KEEP THIS INSTRUCTION MANUAL FOR REFERENCE
BATTERY WARNING – ALKALINE (AA)
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
- Insert batteries using the correct polarity. Do not short-circuit the supply terminal.
- Only use manufacturer specified battery(ies), charger(s), and/or adapters, if applicable, specified by the manufacturer.
- Always use, replace, and recharge (if applicable) batteries under adult supervision.
CHARGING BATTERY
Note: The charging light on the drone will light up when it is charging and turn off when fully charged. Charge time is approximately 120 minutes.
- Turn off the drone before charging.
- Connect the Battery Charger Cable to the port found on the rear of the drone.
- Connect the USB connector to the power source.
Replacing Propellers
- Pull firmly to remove the broken propeller. Replace with a new one. Push firmly and carefully.
- Replace propellers by following the diagram on the right.
- Each blade spins differently. Blade A1 turns clockwise and Blade B1 turns counterclockwise.
REMOTE OVERVIEW
OPERATING DRONE
Step 1 – Pre-Flight Checklist
- Read all warnings and instructions.
- Install remote batteries, page 2.
- Charge batteries, page 3.
- Make sure that the drone and remote are powered off.
Step 2 – Choosing a location
- The drone is designed to be flown/driven indoors and outdoors.
- Always make sure you have enough space to fly a drone.
- Always follow warnings, page 1.
Step 3 – Driving Mode
-
Turn the drone and remote on then place the drone on a hard flat surface and allow it to sit for 4 seconds.
-
Pair remote to drone: Bring the Throttle all the way up then bring it all the way down, remote will beep once paired.
-
Use the Multi-Directional Joystick to move forwards, backward, or turn left and right.
Note: After the pair is successful, keep the throttle down all the way,
to enter driving mode.
After the pair is successful, you can enter flying mode by following step 4
(shown below)
Step 4 – Lift Off
-
Bring the car to a stop.
-
Slowly and carefully press the Throttle Joystick up. Drone will begin to elevate. You can compensate for some of the drone’s drifting by using the Multi-Directional Button or by following step 5. You may need to practice this step several times before successfully getting the drone into the air.
Step 5 – Operating Drone in Flight
Follow this step if your drone begins to drift while taking off or during
flight.
F. Drone drifts backward: Press the Forward Adjustment Button.
B. Drone drifts forwards: Press the Backwards Adjustment Button.
L. Drone drifts right: Press the Left Adjustment Button.
R. Drone drifts Left: Press the Right Adjustment Button.
SPIN TRIM
Drone spin clockwise automatically: Press the left spin trim adjustment
button.
Drone spin to counter-clockwise automatically: Press the right spin trim
adjustment button.
Step 6 – Landing Drone
- Make sure you have achieved level, balanced flight, where the drone is neither climbing nor descending. This mode allows you to safely and slowly land your drone without having to control the speed.
- The ideal auto-landing height is 20ft.
- Press the land button to trigger auto land. The Remote will beep continuously and the button will be light on until you exit the auto land mode.
- To steer the drone during landing, use the right control until the drone has reached the ground.
- Press the land button again to exit auto-landing mode.
- For any urgency stop, press the Land button and hold on until the power cut off and the blades stop spinning.
Step 7 – Retrieving Drone
- Turn off your remote by rotating the ON/OFF Button. This will stop you from accidentally turning the propellers on.
- Make sure the propellers have stopped spinning then pick up your drone.
Note: You will need to pair your drone again before your next flight.
Align
Press the Align Button to turn Align mode ON and then again to turn it off.
The button will be light on when in Align mode.
In this mode, the drone will always move in the direction you press the Multi-
Directional Button no matter which way the drone faces.
Tips
-
Do not crash the drone into sand or dirt.
Drone gears may become clogged. -
When first learning to fly, practice lifting off and hovering.
-
Stay several feet from walls and buildings.
Printed in China.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>