KARCHER PS 30 Plus Power Scrubber Surface Cleaner Instruction Manual

KARCHER PS 30 Plus Power Scrubber Surface Cleaner

General notes

Read the original instructions before using the device for the first time and act in accordance with it. Keep the original instructions for future reference or for future owners.

Safety instructions

CAUTION

• Do not use the device when persons are in the vicinity of the cleaning head.

• Switch the high-pressure cleaner off and disconnect the power scrubber from the high-pressure gun after finishing cleaning work and before performing an  work on the high-pressure cleaner.

• Do not trigger the high-pressure jet at the high-pressure gun until the power scrubber is on the  surface to be cleaned.

• Recoil danger. Keep proper footing and hold the highpressure gun and extension tube firmly.

• Maximum water temperature 60 °C (please observe  the instructions for your high-pressure cleaner).
  Note

• Be sure to always adhere to the safety instructions for your high-pressure cleaner and the locally applicable regulations and directives

Illustrations and descriptions in these operating instructions

Illustrations and descriptions in these operating instructions may differ from the scope of delivery and equipment for your device.
Note Subject to technical changes without notice

Environmental protection

| The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.
---|---
| Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.

Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.de/REACH

Intended use

The power scrubber PS 30 Plus can be used with all Kärcher Home & Garden pressure washers manufactured in 1992 or later, up to a pressure of 18 MPa (180 bar / 2600 psi).
For devices manufactured up to 1991, an additional  adapter is required (see chapter Accessories and spare parts ).
The power scrubber is ideally suited for high-pressure cleaning of primarily smooth, outdoor floor areas and stairs with various different surfaces such as tiles, stone, concrete, plastic and wood.
Indoor areas such as laundry rooms or garages can also be cleaned as long as they have suitable water drainage facilities.
Only use the power scrubber PS 30 Plus in private households.

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely. Information on accessories and spare parts can be found at www.kaercher.com.

Description of the unit

For the illustrations, refer to the graphics page
Illustration A

① Bristle crown
② Squeegee blade
③ Hinge
④ Union nut
⑤ Bayonet connector
⑥ Extension tube
⑦Rotary knob for adjusting the side nozzle
⑧ Rotatable side nozzle
⑨Rigid high-pressure nozzle

Mounting the extension tube

Note
Ensure that the device components are tightly connected on installation.
Illustration B

1. Insert the bayonet connection into the mounting.
2. Turn the extension tube until it engages in place.
3.  Tighten the union nut.
   Repeat the procedure for further extension tubes if applicable.

Initial startup

Note
You can use the extension tubes with any KÄRCHER accessories.
The extension tubes must be installed prior to use (see chapter Mounting the extension tube).

1. Connect the device to the high-pressure gun

Operation

Cleaning floor areas

Remove coarse dirt from the surface to be cleaned (e.g. by sweeping) before using the device to avoid damage.
Note

• Test the device on an inconspicuous area before using on sensitive surfaces, e. g. wood.
• Do not allow it to remain in one area, but keep it in motion.

1. Place the power scrubber onto the surface to be cleaned.
   Illustration C
   

2. Make sure the side nozzle is directed towards the floor area. If this is not the case, turn the rotary knob clockwise to adjust the side nozzle until it is pointing downwards.

3. Unlock the lever of the high-pressure gun.

4. Press the lever of the high-pressure gun. The device switches on.

5. Clean the floor area.

6. Wet, smooth surfaces can be dried using the squeegee blade.
   Illustration D
   
   

Cleaning edges and corner areas

The side nozzle and cleaning head can be turned for convenient cleaning of edges and corner areas.

1. Turn the rotary knob counter-clockwise to adjust the side nozzle.
   Illustration E
   
   The side nozzle is directed to the side.

2. If necessary, turn the cleaning head in the desired direction.
   Illustration F
   

3. Unlock the lever of the high-pressure gun.

4. Press the lever of the high-pressure gun. The device switches on.

5. Clean the edges or corner areas using even movements.

After use

Rinse off the device with a gentle water stream after use.

• Remove the power scrubber and extension tubes, if applicable, from the high-pressure gun.
• Rinse off the power scrubber with the high-pressure gun (without accessories) or wipe down with a damp cloth.

Storage

Store the device in a frost-protected place

Care and service

Removing/Installing the nozzles

The described procedure applies to all nozzles on the device.
Illustration G

1. Remove the clip.
2. Pull the high-pressure nozzle out.
3. Fit the high-pressure nozzle.
4. Fit the clip

Cleaning the high-pressure nozzle

1. Remove the high-pressure nozzle.
2. Flush the high-pressure nozzle with clear water in both directions. Replace a damaged high-pressure nozzle where necessary.
3. Install the high-pressure nozzle

Replacing the squeegee blade

A damaged or worn squeegee blade can be replaced without the use of tools.

1. Lift up the squeegee blade.
2. Pull the squeegee blade up and out of the power scrubber.
3. Fit the new squeegee blade into the groove and press firmly into place.
   Illustration H
   
   

Troubleshooting guide

The high-pressure cleaner does not build up pressure or it pulses The high- pressure nozzles are blocked or damaged

1. Remove the high-pressure nozzles.
2. Check the high-pressure nozzles for clogging and clean if necessary.
3. Check the high-pressure nozzles for damage and replace if necessary.
4. Flush the power scrubber with clear water without the nozzles fitted.
5. Install the high-pressure nozzles

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.(See overleaf for the address)

THANK YOU!
Register your product and benefit from any advantages.
www.kaercher.com/welcome

Rate your product and tell us your opinion

Register your product
www.kaercher.com/welcome

www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40 71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

References

• Cher - Official Site
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher
• Reinigungsgeräte und Hochdruckreiniger | Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>