JOY-iT SBC-OLED01 OLED Display 128×64 Module Instruction Manual

: June 5, 2024
: JOY-It

Table of Contents

GENERAL INFORMATION
I2C ADRESSE
USAGE WITH ARDUINO
USAGE WITH RASPBERRY PI
OTHER INFORMATION
SUPPORT
Documents / Resources

OLED DISPLAY 128X64
SBC-OLED01 JOY iT SBC OLED01 OLED Display 128x64
Module

GENERAL INFORMATION

Dear customer,
Thank you for purchasing our product. In the following, we will show you which things should be noted during the use.
Should you encounter any unexpected problems, do not hesitate to contact us.

I2C ADRESSE

On the backside of the OLED display is a resistor, with which you can set the I2C address of the display to 0x3D. In the delivery state, the display is accessible via the I2C address 0x3C.
To change the address, re-solder the resistor marked in the figure.

USAGE WITH ARDUINO

3.1 Connection The SBC-OLED01 has a logic level of 3.3V. Therefore, when using an Arduino Uno, a voltage translator must be used, otherwise, it may cause damage to the display. In our example, we use the COM-KY051VT.

JOY iT SBC OLED01 OLED Display 128x64 Module - Fig 1

OLED	Arduino	Voltage translator
GND	GND	GND
VCC	5V	VCCb
–	3,3 V	VCCa
–	A5	B2
SCL	–	A2
–	A4	B1
SDA	–	A1

3.2 Code example
Before you can transfer the code example to your Arduino using your Arduino IDE, you must first install the additional libraries Adafruit GFX Library (released under the BSD License) and Adafruit_SSD1306 (released under the BSD License) from Adafruit.
These libraries allow you to use the display as easily and quickly as possible. You can search for and install them under Sketch → Include Library → Manage Libraries….

You can download our code examples here. You can upload the code to your Arduino using the Upload button. Make sure that you have selected Port and Board correctly under Tools.

USAGE WITH RASPBERRY PI

Connection

JOY iT SBC OLED01 OLED Display 128x64 Module - Fig
2

OLED	Raspberry Pi
GND	GND
VCC	3,3V
SCL	GPIO 3 (SCL)
SDA	GPIO 2 (SDA)

Installation

First, enable I2C on your Raspberry Pi. To do this, enter the following command into your console. sudo raspi-config JOY iT SBC OLED01 OLED Display
128x64 Module - Fig 3

Now, enter the following commands to install the necessary libraries.
sudo apt-get install python3-pip
sudo apt-get install python3-pil
Now, open the config.txt to increase the baud rate for the display. To do this, execute the following command.
sudo nano /boot/config.txt
Add the following line at the end of the file.
[all] dtparam=i2c_baudrate=1000000

Save the file with CTRL + O and close it with CTRL + X.
Now restart the Raspberry Pi with the following command.
sudo reboot
For the display, we use the Adafruit CircuitPython SSD1306 library from Adafruit, which is released under the MIT License. You can download it with the following command.
sudo pip3 install adafruit-circuitpython-ssd1306

Code example

You can download our sample code with the following command.
wget https://www.joy-it.net/files/files/Produkte/SBC-OLED01/SBC- OLED01_Codeexample_RaspberryPi.zip
Unzip the file with the following command.
unzip SBC-OLED01_Codeexample_RaspberryPi
You can now execute the code with the following command. Please note that the directory may differ.
cd SBC-OLED01_Codeexample_RaspberryPi python3 SBC-OLED01.py

OTHER INFORMATION

Our information and take-back obligations according to the Electrical and Electronic Equipment PR Act (ElektroG)
The symbol on electrical and electronic equipment:

This crossed-out dustbin means that electrical and electronic appliances do not belong in the household waste. You must return the old appliances to a collection point. Before handing over waste batteries and accumulators that are not enclosed by waste equipment must be separated from it.c

Return options:
As an end-user, you can return your old device (which essentially fulfills the same function as the new device purchased from us) free of charge for disposal when you purchase a new device.
Small appliances with no external dimensions greater than 25 cm can be disposed of in normal household quantities independently of the purchase of a new appliance.

Possibility of return at our company location during opening hours:
SIMAC Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn, Germany

Possibility of return in your area:
We will send you a parcel stamp with which you can return the device to us free of charge. Please contact us by email at Service@joy-it.net or by telephone.

Information on packaging:
If you do not have suitable packaging material or do not wish to use your own, please contact us and we will send you suitable packaging.

SUPPORT

If any questions remained open or problems may arise after your purchase,we are available by e-mail, telephone and ticket support system to answer these.

E-Mail: service@joy-it.net
Ticket-system: http://support.joy-it.net
Telephone: +49 (0)2845 98469 – 66 (10 – 17 o’clock)

For further information visit our website: www.joy-it.net

Published: 06.01.2022

www.joy-it.net
SIMAC Electronics GmbH
Pascalstr. 8, 47506 Neukirchen-Vluyn

Documents / Resources

| JOY- iT SBC-OLED01 OLED Display 128x64 Module [pdf] Instruction Manual
SBC-OLED01, OLED Display 128x64 Module, SBC-OLED01 OLED Display 128x64 Module
---|---