Amica JSM 4011 Slow juicers Instruction Manual

June 5, 2024
Amica

Amica JSM 4011 Slow juicers

Overview

Amica-JSM-4011-Slow-juicers-fig-1

Amica-JSM-4011-Slow-juicers-fig-2

Amica-JSM-4011-Slow-juicers-fig-3

Amica-JSM-4011-Slow-juicers-fig-4

Amica-JSM-4011-Slow-juicers-fig-5

Amica-JSM-4011-Slow-juicers-fig-6

SAFETY INSTRUCTIONS FOR USE

Important! To minimize the risk of fire, electric shock or injury:

  • Carefully read this instruction before using the appli-ance.
  • Children do not realize the dangers that can arise when using electrical appliances; therefore keep the appliance out of reach of children.
  • Do not immerse the body of the appliance in water or other liquids. Immersing in water may cause an electric shock.
  • If water spills on the external components of the ap-pliance, dry it thoroughly before switching back on. Do not touch wet surfaces in contact with the appli-ance connected to power supply, immediately dis-connect it from the mains.
  • Do not use the appliance if it shows any signs of damage to the power cord, or if the appliance has been dropped on the floor.
  • After use, always pull out the plug from the socket, and also in case of any malfunction, before cleaning or before changing accessories.
  • When pulling out the plug from the wall outlet, never pull by the cord, only the plug, holding the socket with your other hand.
  • The appliance is Class I fire protection electrical equipment.
  • Do not attempt to remove any parts of the housing.
  • To prevent damage to the power cord, do not place it over sharp edges or close to hot surfaces.
  • Do not expose the appliance to rain or humidity, and do not use it outdoors. Do not operate the appliance with wet hands.
  • If the power cord or plug is damaged, it should be replaced by a professional repair shop in order to avoid hazard.
  • Using attachments that were not supplied with the product may cause damage to the appliance.
  • Never place the appliance on hot surfaces.
  • Never leave the appliance connected to the mains without supervision.
  • This appliance is not intended for use by persons (including children) with physical, mental or sensory handicaps, or by persons inexperienced or unfamil-iar with the appliance, unless under supervision or in accordance with the instructions as communicat-ed to them by persons responsible for their safety. Children shall not play with the appliance.
  • Pull the plug from the wall outlet before replacing accessories.
  • This appliance can be used by children aged 8 years and older or by persons with physical, mental or sensory handicaps, or by those who are inexpe-rienced or unfamiliar with the appliance, provided they are supervised or have been instructed how to safely use the appliance and are familiar with risks associated with the use of the appliance.
  • Ensure that children do not play with the appliance. Clean-ing and maintenance of the appliance should not be performed by children unless they are 8 years or older and are supervised by a competent person.
  • The surface on which the appliance is used shall be levelled, clean and dry.
  • The appliance is designed for juicing such foodstuffs as fruits or vegetables, do not use it for other pur-poses.
  • Take caution when cleaning the attachments
  • Before use, check that the lid is securely attached.
  • To push the product, only use the supplied pusher.
  • Turn on the appliance by pushing or . Turn off the appliance by pushing . The complete appliance shutdown is possible by disconnecting the appliance from the power supply.
  • Do not overload the appliance with an excessive amount of products or too strong pressing with the pusher.
  • Change the direction of head rotation by pressing , if you notice strong vibrations or rotation reduction. If necessary, turn off the appliance, unplug it from power, remove all components, clean the sieve and other parts in contact with food.
  • Stop work and unplug the appliance from the wall outlet when the product is jammed in the hopper. Remove the cause of jamming.
  • Do not allow any liquid to come in contact with the appliance body/motor.
  • Before you put the plug into the wall outlet, make sure your hands are dry.
  • Never touch rotating parts when the appliance is in operation.
  • Do not use the appliance without properly secured attachments.
  • After use, disconnect the appliance from the power supply.
  • Do not tamper with the safety lock before turning the appliance on without properly secured attachments.
  • Products with fine and hard seeds, such as currants, raspberries, grapes or chokeberries should be pro-cessed in small portions (~0.3kg). After each batch of juice, turn off the appliance and thoroughly clean the separator tank according to the relevant sec-tions of the Operating Instructions.
  • When the tanks is nearly full, and the pulp or juice does not flow through the holes, turn off the appli-ance and thoroughly clean the separator tank ac-cording o the relevant sections of the Operating Instructions.
  • It is recommended to remove seeds from fruits that may change the juice taste, and in extreme situa-tions may cause damage to the appliance.

Electrical requirements
Make sure that the voltage indicated on the nameplate cor-responds to that of your home electrical mains. Alternating current must be used, typically marked ~.

DISPOSINqaG/SCRAPPING OF USED EQUIPMENT

UNPACKING

During transportation, protective packaging was used to protect the appliance against any damage. Af­ter unpacking, please dispose of all elements of packaging in a way that will not cause damage to the environ­ment.

All materials used for packaging the appliance are environmentally friendly; they are 100% recyclable and are marked with the appropriate symbol.
Important! Packaging materials (bags, polyethyl­ene, polystyrene, etc.) should be kept away from children during unpacking.

DISPOSAL OF OLD APPLIANCE

In accordance with European Directive 2012/19/EU and local legislation re­garding used electrical and electronic goods, this appliance is marked with the symbol of the crossed­out waste container. This marking indicates that the appliance must not be disposed of together with other household waste after it has been used.
The user is obliged to hand it over to waste collec­tion center collecting used electrical and electron­ic goods. The collectors, including local collection points, shops and local authority departments pro­vide recycling schemes.
Proper handling of used electrical and electronic goods helps avoid environmental and health haz­ards resulting from the presence of dangerous com­ponents and the inappropriate storage and process­ing of such goods.

INDIVIDUAL FITTINGS

1. Pusher 10. Juice outlet
2. Hopper 11. Juice outlet plug
3. Worm shaft 12. Appliance body
4. Stainless steel sieve (large mesh) 13. Control Panel
5. Stainless steel sieve (small mesh) 14. Drive shaft
6. Juice scraper 15. Pulp container
7. Cleaning brush 16. Juice container (1,000 ml)
8. Separator container 17. Juice scraper
9. Pulp outlet

OPERATION, CLEANING AND MAINTENANCE

Before first use

  • After unpacking the appliance, make sure that the set includes all the attachments, and if there are no visible signs of damage.
  • Before first use, wash in hot water all the attachments which come into contact with food. In addition, thoroughly dry all parts before use.
  • Never immerse the body of the appliance in water or other liquids. This can cause damage to the mo-tor and pose a risk of electric shock.
  • Wash all food products before juicing. Cut large fruits, such as apples, into smaller pieces to fit into the inlet.
  • Do not use frozen products.
  • Remove hard seeds and pits before juice extraction.

Before assembling the appliance, make sure that the power cord is disconnected from the wall outlet.

How to use a slow-speed juicer

  • Expand the power cord, place the body of the appliance on a stable, dry and flat surface.
  • The order of assembly of individual components is shown on Fig. 2a.
  • Make sure that the rubber protective buffer is fixed on the pulp outlet hole at the bottom of the separator container (Fig. 2b).
  • Make sure that the separator container gasket (Fig. 2i) and the juice outlet plug gasket (Fig. 2j) have been installed correctly.
  • Place the separator container on the appliance body (Fig. 2a, item 1) in such a manner that the two ridges in the body fit into the grooves in the bottom of the separator container (Fig. 2c, item 2). Make sure that the components are properly connected.
  • Connect the stainless steel filter with a juice scraper (Fig. 2d).
  • Put the two-element unit (filter and scraper) inside the separator container (Fig. 2f), bearing in mind that there is a socket inside the container (partially covered by the protective buffer), which should fit the edging in the filter (Fig. 2e, item 1). Make sure that the components are properly connected (Fig. 2f).
  • Insert the worm shaft in the separator container unit along with other fitted components (Fig. 2f). Make sure that the worm shaft is properly secured on the drive shaft. Otherwise, the container will not close.
  • Close the separator container by putting the hopper on (Fig. 2g). Put the hopper on the vessel in such a manner that the triangle symbol on the separator container and an open padlock symbol on the hopper were in a straight line (Fig. 2f). Then turn the lid clockwise until it clicks into place. Make sure that the elements are properly connected (the triangle symbol on the vessel and a symbol of a closed padlock on the hopper must be aligned (Fig. 2g). Incorrect installation will prevent the start of appliance.
  • Put the juice container under the juice outlet and the pulp container under the pulp outlet (Fig. 2h).

OPERATION, CLEANING AND MAINTENANCE

The Control panel features 4 buttons (Fig. 3)

To start the motor and start the appliance operation, press the “Juicing” button (Fig. 3, item 1).
To turn off the motor, press the “Stop” button (Fig. 3, item 4).
Hold down the “Long press to reverse” button for 2-5 seconds (Fig. 3, item 3) to change the direction of rotation. This mode is used only when the products used are jammed in the shaft. To return to normal operating mode, press “Juicing”.
The „Mixing” button (Fig. 3, item 2) activates the mixing function.
Juicing function

Put the prepared products in the hopper and start the appliance by pressing the “Juicing” button on the control panel (Fig. 3, item 1).

While operating in the juicing function, juice outlet plug must open at all times. Failure to do so will result in juice staying in the appliance, which may lead to overflow, and consequently to the appliance failure.

  • When the appliance is in operation, put in products of suitable size through the inlet hole (cut larger fruits or vegetables into smaller pieces), and press products with the pusher. Within seconds the juice will start to flow, and the pulp will be pushed into the pulp container through the outlet. Do not press the product too hard with the pusher, this may result in stopping the drive shaft.
  • If the appliance jams during operation and stops working, turn it off with the “Stop” button (Fig. 3, item 4), and then press and hold the “Long press to reverse” (Fig. 3, item 3) for 3-5 seconds. After a complete stop of the shaft try to restart the appliance. If necessary, repeat this process 2-3 times. If the appliance still operates improperly, turn it off, disconnect from the mains, dismantle and remove the products from inside the appliance.
  • When the juice vessel or pulp container is full, switch off the appliance and empty the containers.

Mixing function-extraction and mixing different kinds of juice

  • Close the juice outlet plug.
  • Start juicing as described in section Juicing function -put in products in random order.
  • Ensure that the level of juice in the separator container did not exceed the marked level of 450 ml.

While using mixing function, the juice outlet plug must be closed.
The extracted and mixed juice level in the separator container must not exceed the maximum marked level. Exceeding the maximum level could lead to overflowing, and consequently to the appliance failure.

  • Press the “Mixing” button (Fig. 3, item 2) to mix all kinds of juices.
  • Open the juice outlet plug to empty the separator container.
  • When the juice vessel or pulp container is full, switch off the appliance and empty the containers.

Never use hands or items not suitable for the appliance to push the products in hopper (for example, a tablespoon). Only use the pusher supplied with the appliance. After processing all products, switch off the appliance with the “Stop” button and pull out the plug from the wall outlet.
The maximum time of continuous operation is 20 minutes. After this time, turn off the appliance and wait until the motor temperature reaches room temperature. Longer continuous use of the appliance may lead to motor damage. Intervals between operating cycles should be a minimum of 30 minutes.

Attaching the juice spout gasket (Fig. 2i)

  • Open the juice outlet plug.

  • Hold the gasket as shown in the figure.

  • Hold the separator container and juice outlet plug.

  • Attach/remove the gasket.

  • Fit the gasket in a correct position. Incorrect fitting may cause juice leaks.
    Attaching the separator container gasket (Fig. 2j)

  • Hold the gasket in such a way that its ring was directed upwards.

  • Insert the gasket in the groove of the gasket in the separator container.

  • If the separator container gasket is not properly fitted, fit it correctly using for example the brush supplied.

OPERATION, CLEANING AND MAINTENANCE

Practical everyday tips

  • Use fresh products as they have the most juice. Food products such as pineapple, beetroot, celery stalks, apples, cucumbers, carrots, spinach, melon, tomato, pomegranate, citrus and seedless grapes are particularly suitable for processing in the appliance.
  • You do not have to remove thin peel from products, peel off thick peel from products such as oranges, pineapple, uncooked beetroot. Also remove white flesh found directly under the peel of citrus, it has a bitter taste.
  • When preparing apple juice, remember that the type of apples affects density of the juice. Apple juice goes brown fast, to reduce this effect, add a few drops of lemon juice to the juice. This will slow down juice browning.
  • Products such as bananas, papayas, avocados, figs or mangoes are not suitable for processing in the appliance. It is recommended to use a hand blender or a food processor for processing this type of fruit.
  • Stalks and leaves (for example, lettuce or cabbage) may also be processed in the appliance.
  • The produced juice should be consumed as soon as possible. The juice loses its original taste and nutritional value in prolonged contact with air.
  • To obtain as much juice out of the products as possible, slowly press the products with a pusher.
  • The appliance is not suitable for processing hard, fibrous and/or starchy products, such as sugar cane.
  • It is not recommended to reprocess the extracted pulp. This causes dense pulp clot in the juice outlet.
  • Density of the juice is affected by the type of processed food

Cleaning

  • Before cleaning the appliance, make sure that it is in complete stop and disconnect it from the mains. Furthermore, it must cool down completely.
  • Wipe the appliance body with a damp cloth and then dry thoroughly. Do not immerse the body in water or any other liquid.
  • Wash other attachments in warm water with mild detergent, preferably immediately after finishing work. This will facilitate removing the food residues.
  • Certain parts of the appliance can be washed in the dishwasher (maximum washing temperature is 45OC).
  • To clean the filter, use the supplied brush (Fig. 1, item 8).
  • Do not use abrasive or harsh cleaning agents.
  • In order to thoroughly wash the pulp outlet, pull out the rubber protective buffer from the pulp outlet in the separator container, and then clean the outlet with a brush (Fig 2i, 2j).
  • Before cleaning the juice scraper, remover silicone brushes (Fig. 2k). Secure them back in place after cleaning (Fig. 2l).
  • Dry all parts and assemble the appliance.
  • Store the appliance in a dry place. Juice container can be stored in the pulp container

Be careful when cleaning the filter as it may cause cuts.
Types of strainers and their applications (Fig. 4)
Fine strainer (Fig. 4, item A) — use it for hard and/or fibrous food products. The juice squeezed using this strainer is clearer.
Coarse strainer (Fig. 4, item B) — use it for soft fruits such as strawberries, kiwi or tomatoes. Do not use this strainer for juicing fruits with small seeds. The juice squeezed using this strainer is thick.

OPERATION, CLEANING AND MAINTENANCE

Amica-JSM-4011-Slow-juicers-fig-7

RECIPES FOR DELICIOUS DRINKS

Energy cocktail-

  • 2 cups chopped carrots
  •  0.5 cup cut cucumber
  •  12 spinach leaves
  •  1 peeled lime
  •  1 cup cut celery
  •  1 apple
  •  1 tomato
  •  2 tablespoons honey
    Process all products in the juicer, add honey and mix. Serve immediately with a few ice cubes.

Temptation Cocktail

Process all products in the juicer and mix well. Add 6 ice cubes, serve in medium-sized glasses dec-orated with strawberries, cherries and an orange slice.

Miracle Cocktail

  • 1 cup cut and peeled pineapple
  •  1 cup cut apple
  •  2 small chopped carrots
  •  1 peeled orange
  •  2 chopped celery stalks

Process all fruits and vegetables in the juicer. Serve immediately with a few ice cubes.

Fruit Jug- Pourri

  •  4 medium apricots, seedless
  •  2 cups peeled and cut melon
  •  1 large apple
  •  1 peeled orange
  •  1 cup cut celery
  •  1 apple
  •  1 tomato
  •  2 tablespoons honey

Process all fruits and vegetables in the juicer. Serve immediately with a few ice cubes.

Pink Cloud Cocktail

  • 1 cup strawberries
  •  1 peeled orange
  • 1 peeled pear
  • 1 small chopped carrot

Process all fruits and vegetables in the juicer. Serve immediately with a few ice cubes.

Multifruit juice

  •  0.5 peeled and cut pineapple
  •  2 peaches, seedless
  •  2 small ripe pears
  •  1 small chopped carrot

Process all fruits and vegetables in the juicer. Serve immediately.

SPECIFICATION

Type| JSM 4011| JSM 4012 /

JSM 4013

---|---|---
Rated voltage| 220-240V

~50/60Hz

| 220-240V

~50/60Hz

Rated power| 200 W| 200 W
Power Cord| 1 m| 1 m
Net weight| 4,7 kg| 4,6 kg

WARRANTY AND AFTER-SALES SERVICE

Warranty service as stated on the warranty card.
The manufacturer shall not be held liable for any damage caused by improper use of the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals