Cobra CPJS 1000A Lithium-Ion Jump Starter and Power Bank with Fast Charge USB User Guide
- June 5, 2024
- Cobra
Table of Contents
Jump Starter 1000A
Lithium-Ion Jump Starter & Power Bank
With Fast Charge USB
FULLY CHARGE FIRST!
For optimal performance, charge your Cobra Jump Starter prior to first use
and every 12 months.
QUICK START GUIDE
Thank you for purchasing the Cobra Jump Starter 1000 A
Jumpstart your vehicle’s dead battery and keep your portable devices powered
and charged with this heavy-duty Lithium-Ion jump starter and power bank. Fast
charge USB ports allow you to charge multiple portable devices at once, while
two starting options allow you to start your vehicle either from the direct-
to-battery connection or through the in-car connection using the 12V outlet
inside your vehicle. Keep this in your vehicle for when you or others will
need it!
Count on Cobra for Power When You Need It.
Download the full Cobra Jump Starter 1000A manual at:
cobra.com/manuals
Cobra® and the snake design are registered trademarks of Cobra Electronics
Corporation, USA. Cobra Electronics CorporationTM is a trademark of Cobra
Electronics Corporation, USA. Other trademarks and trade names are those of
their respective owners.
• ©2021 Cobra Electronics Corporation
Jump Starter 1000A Features
A. LED Display
B. Power/Flashlight Button
C. Jump Start Connector
D. LED Flashlight
E. USB-C Fast Charge Input/Output| F. (2) USB-A Fast Charge Outputs
G. 12V Jump Start Connector
H. Jump Start Cable
I. USB-C to USB-A Cable
J. 12V Jump Start Cable
---|---
Jump-Starting Your Vehicle: Direct-to-Battery
- connect the jumper cable clamps to the battery terminals (First, Red to Positive, then Black to Negative)
- 10 Wait for the Green LED light to appear on the JumpStart cable and then start your vehicle
- Connect the jumper cables to the Jump Starter 1000A
- Disconnect the jumper cable from the Jump Starter 1000A and then from the battery
Jump-Starting Your Vehicle: In-Car
-
Turn off all vehicle accessories. Connect the jumper cable to the Jump Starter 1000A
-
Depending on your vehicle, push the START button to the Accessory mode or turn the ignition switch to the Accessory position
-
Connect the jumper cable plug into the vehicle’s 12V accessory port
NOTE: The 12V plug is used for in-car jump starling only. For instructions on recharging the Jump Starter 1000A, please see “Re-Charging Your Jump Starter 1000A”
-
Wait for “Output Ready’ and 5 solid charging bars on your Jump Starter’s LED screen and then start your vehicle.
-
Disconnect the Jump Start cable from the 12V accessory port and from the Jump Starter 1000k Leave the engine running for at least twenty minutes to allow the vehicle’s battery to recharge.
NOTE: The in-car battery charging from the Jump Starter 1000A will take up to 15 minutes. If your vehicle does nattiest with the in-car method, try the direct-to-hatterSennethOd.
Charging Your Devices
Re-Charging Your Jump Starter 1000A
In-Car Jump Starting FAQ
How do I know if my battery is charging? When the 12V jumper cables are plugged into the Jump Starter 1000A and the vehicle’s 12V accessory port, the LCD screen will show a flashing 5-bar graph and the word ‘Output’. As your battery charges the flashing bars will begin to turn solid until the vehicle is ready to start, at which point a ‘Ready’ message will appear on the screen and you are ready to start your vehicle.
How long will it take to charge?
In-car jump-starting will take longer than jump-starting with a direct-to- battery connection, up to 15 minutes total. If your vehicle does not start with the in-car method, try to jump-start with the direct-to-battery method.
What if I don’t see the charging bars?
If the Jump Starter 1000A does not have enough charge to jump start from
within the car, the current battery percentage will flash and a caution image
will appear. In that case, you will need to jump-start your vehicle by using
the direct-to-battery method.
Tri-Color Status LED:
The Status LED will illuminate and the color will change if the following
conditions are present:
| LED | CONDITION |
|---|---|
| No LED | Connection not detected or the Jump Starter 1000A battery is |
depleted. Check the battery charge level and verify the connection of the
jumper cable to the Jump Starter 1000A.
Solid Red| Reverse polarity connection. Reverse the clamps.
Flashing Red| Over-current protection. Wait for 30 seconds and then
retry the connection.
Solid Yellow| Solid contact established and charging for a jump start.
Flashing Yellow| Either the cables are not properly connected or the
Jump Starter 1000A is too hot. Remove the cable and retry the connection.
Red and Green Flashing Alternatingly| Safety feature to prevent the
battery from overheating from too many jump start attempts in a short period
of time.
Remove the cable and wait a few minutes.
Solid Green| 1Ready to jump-start your vehicle.
NOTE: When connected to your vehicle’s battery and charging, the Jump Starter 1000A will make a clicking sound every 5 seconds. This is part of normal operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>