greenworks CSF301 Chainsaw User Manual

CHAINSAW OPERATOR MANUAL

DESCRIPTION

1.1 PURPOSE

This machine is designed for cutting branches, trunks, logs, and beams of a diameter determined by the cutting length of the guide bar. It is only designed to cut wood. It is only to be used in an outdoor, domestic application by adults.
Do not use the machine for any purpose not listed above.
This machine is not to be used for professional tree services.
It is not to be used by children or by persons not wearing adequate personal protective equipment and clothing.
This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their safety.

1.2 OVERVIEW

1 Guide bar cover
2 Front handle guard
3 Front handle
4 Lockout button
5 Rear handle
6 Trigger
7 Oil indicator| 8 Oil tank cap
9 Chain
10 Guide bar
11 Bucking spikes
12 Chain tension knob
13 Chain cover
14 Chain cover knob
---|---

1.3 PACKING LIST

1. Chainsaw
2. Scabbard
3. Manual.

GENERAL POWER TOOL SAFETY WARNINGS

**WARNING**
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your battery-operated (cordless) power tool.

2.1 WORK AREA SAFETY

• Keep work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2.2 ELECTRICAL SAFETY

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

2.3 PERSONAL SAFETY

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A lapse of attention while operating power tools may result in serious personal injury.
• Use personal protection. Always wear eye protection. Protective products such as dust masks, non-skid safety shoes, hard hats, or hearing protection used appropriately will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off position before connecting to a power source and/or battery pack and when picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not over-reach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

2.4 POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of  starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

2.5 BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or fire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with plenty of soap and water. If liquid contacts eyes, immediately seek medical help. Liquid ejected from the battery may cause irritation or burns.

2.6 SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR CHAINSAWS

3.1 GENERAL CHAIN SAW SAFETY WARNINGS:

• Keep all parts of the body away from the saw chain when the chain saw is operating. Before you start the chain saw, make sure the saw chain is not contacting anything. A moment of inattention while operating chain saws may cause entanglement of your clothing or body with the saw chain.
• Always hold the chain saw with your right hand at the rear handle and your left hand at the front handle. Holding the chainsaw with a reversed hand configuration increases the risk of personal injury and should never be done.
• Hold the chain saw by insulated gripping surfaces only, because the saw chain may contact hidden wiring. Saw chains contacting a “live” wire may make exposed metal parts of the chain saw “live” and could give the operator an electric shock.
• Wear eye protection. Further protective equipment for hearing, head, hands, legs, and feet is recommended. Adequate protective equipment will reduce personal injury from flying debris or accidental contact with the saw chain.
• Do not operate a chain saw, on a ladder, from a rooftop, or any unstable support. Operation of a chain saw in this manner could result in serious personal injury.
• Always keep proper footing and operate the chain saw only when standing on a fixed, secure, and level surface. Slippery or unstable surfaces may cause a loss of balance or control of the chain saw.
• When cutting a limb that is under tension, be alert to spring back. When the tension in the wood is released, the spring-loaded limb may strike the operator and/or throw the chain saw out of control.
• Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off balance.
• Carry the chain saw by the front handle with the chainsaw switched off and away from your body. When transporting or storing the chain saw, always fit the guide bar cover. Proper handling of the chain saw will reduce the likelihood of accidental contact with the moving saw chain.
• Follow instructions for lubricating, chain tensioning, and changing the bar and chain. The improperly tensioned or lubricated chain may either break or increase the chance of kickback.
• Cut wood only. Do not use a chain saw for purposes not intended. For example: do not use a chain saw for cutting metal, plastic, masonry, or non-wood building materials. Use of the chain saw for operations different than intended could result in a hazardous situation.
• Do not attempt to fall a tree until you have an understanding of the risks and how to avoid them. Serious injury could occur to the operator or bystanders while falling from a tree.
• This chain saw is not intended for tree felling. Use of the chain saw for operations different than intended could result in serious injury to the operator or bystanders.
• Do not operate a chain saw in a tree unless you have been specifically trained to do so. Operation of a chain saw in a tree without proper training could increase the risk of serious personal injury.
• Follow all instructions when clearing jammed material, storing, or servicing the chain saw. Make sure the switch is off and the battery pack is removed.
  Unexpected actuation of the chain saw while clearing jammed material or servicing may result in serious personal injury.

3.2 CAUSES AND OPERATOR PREVENTION OF KICKBACK:

Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of the saw which could result in serious personal injury. Do not rely exclusively upon the safety devices built into your saw. As a chainsaw user, you should take several steps to keep your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:

• Maintain a firm grip, with thumbs and fingers encircling the chainsaw handles, with both hands on the saw and your body and arm positioned to allow you to resist kickback forces.
  Kickback forces can be controlled by the operator, if proper precautions are taken. Do not let go of the chainsaw.

• Do not overreach and do not cut above shoulder height. This helps prevent unintended tip contact and enables better control of the chainsaw in unexpected situations.

• Only use replacement bars and chains specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or kickback.

• Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback.

SYMBOLS ON THE PRODUCT

Some of the following symbols may be used on this product.
Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

Symbol

|

Explanation

---|---
| Direct current – Type or characteristic of current.
****| Precautions that involve your safety.
| Read and understand all instructions before operating the product, and follow all warnings and safety instructions.
| Wear eye and ear protection.
| Do not expose the product to rain or moist conditions.
| Avoid bar nose contact.
| Hold with both hands.
| DANGER! Be careful with kickbacks.
| Wear non-slip, heavy-duty gloves.
| Keep all bystanders at least 50 feet (15 m) away.

RISK LEVELS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYM- BOL| SIGNAL|

MEANING

---|---|---
**| DANGER| Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
**| WARNING| Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
**| CAUTION| Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
| CAUTION**| (Without Safety Alert Symbol) Indicates a situation that may result in property damage.

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

****The toxic and corrosive materials below are in the batteries used in this machine: Lithium-Ion, a toxic material.

WARNING
Discard all toxic materials in a specified manner to prevent contamination of the environment. Before discarding a damaged or worn-out Li-ion battery, contact your local waste disposal agency, or the local Environmental Protection Agency for information and specific instructions. Take the batteries to a local recycling and/or disposal center, certified for lithium- ion disposal.

WARNING

If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use it. Discard it and replace it with a new battery pack. DO NOT TRY TO REPAIR IT! To prevent injury and risk of fire, explosion, or electric shock, and to avoid damage to the environment:

• Cover the terminals of the battery with heavy-duty adhesive tape.
• DO NOT try to remove or destroy any of the battery pack components.
• DO NOT try to open the battery pack.
• If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in the eyes or on the skin, and do not swallow it.
• DO NOT put these batteries in your regular household trash.
• DO NOT incinerate.
• DO NOT put them where they will become part of any waste landfill or municipal solid waste stream.
• Take them to a certified recycling or disposal center.

PROPOSITION 65

WARNING
This product contains a chemical known to the state of California to cause cancer, birth defects, or other reproductive harm. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals
are:

• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products;
• Arsenic and chromium from chemically treated lumber. Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic
  particles.

Save these instructions.

INSTALLATION

WARNING
Do not change or use accessories that are not recommended by the manufacturer.
WARNING
Do not install the battery pack until you assemble all the parts.

8.1 UNPACK THE MACHINE

WARNING
Make sure that you correctly assemble the machine before use.

WARNING

• If parts of the machine are damaged, do not use the machine.
• If you do not have all the parts, do not operate the machine.
• If parts are damaged or missing, contact the service center.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.

WARNING
For your personal safety, do not insert the battery before the tool is assembled completely.

8.2 ADD THE BAR AND CHAIN OIL

Examine the amount of oil in the machine. If the oil level is low, add the bar and chain oil as follows.

IMPORTANT
Use bar and chain oil that is only for chains and chain oilers.

NOTE
The machine comes from a factory without bar and chain oil.

1. Loosen and remove the cap (8) from the oil tank.

2. Put the oil into the oil tank.

3. Monitor the oil indicator (7) to make sure that no dirt gets into the oil tank while you add the oil.

4. Put the oil cap on.

5. Tighten the oil cap.

6. The whole oil tank will last for approximately 20- 40 minutes.

**IMPORTANT**
Do not use dirty, used, or contaminated oil. Damage can occur to the bar or chain.

8.3 INSTALL THE BATTERY PACK

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the motor stops before you install or remove the battery pack.
• Read and understand the instructions in the battery and charger manual.

1. Align the lift ribs on the battery pack (15) with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

8.4 REMOVE THE BATTERY PACK

1. Push and hold the battery release button (18).
2. Remove the battery pack from the machine.

OPERATION

NOTE
Remove the battery pack and keep your hands clear of the lock-out button when you move the machine.

IMPORTANT
Examine the chain tension before each use.

9.1 EXAMINE THE CHAIN OIL

NOTE
Do not use the machine without sufficient chain oil.

1. Examine the oil level of the machine from the oil indicator.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

8.4 REMOVE THE BATTERY PACK

1. Push and hold the battery release button (18).
2. Remove the battery pack from the machine.

OPERATION

NOTE
Remove the battery pack and keep your hands clear of the lock-out button when you move the machine.

IMPORTANT
Examine the chain tension before each use.

9.1 EXAMINE THE CHAIN OIL

NOTE
Do not use the machine without sufficient chain oil.

1. Examine the oil level of the machine from the oil indicator.
2. Add oil if necessary.

9.2 HOLD THE MACHINE

1. Hold the chainsaw with your right hand on the rear handle and your left hand on the front handle.
2. Hold the handles with the thumbs and the fingers around them.
3. Make sure that your left-hand hold the front handle and your thumb is below the handle.

9.3 START THE MACHINE

1. Press the lock-out button (4).
2. Press the trigger (6) while you hold the lock-out button.
3. Release the lock-out button.

9.4 STOP THE MACHINE

1. Release the trigger to stop the machine.

9.5 FELL A TREE

It is recommended that the first-time user should, as a minimum practice, start cutting logs on a saw-horse or cradle.
Before you start to fell a tree, make sure that:

• The minimum distance between the areas of bucking and felling performed by two or more persons at the same time is two times the height of the tree felled.

• The operation does not:
  • Cause injury to personnel.
  • Hit utility lines. If the tree touches utility lines, immediately tell the utility company.
  • Cause losses in property.

• The user is not in the danger area (24), for example, the downhill side of the area.

• The escape paths (25) that extend back and diagonally behind the felling direction (23) are clear. The feeling direction is controlled by:
  • The natural lean of the tree.
  • The location of larger branches.
  • The wind direction.

• Ensure there is no dirt, stones, loose bark, nails, or staples on the tree.

1. Make a lower-level notching cut (27). Make sure that this cut is:
   a) 1/3 width of the diameter of the tree.
   b) Perpendicular to the felling direction.
   CAUTION
   The level notching cut helps prevent pinching of the saw chain or the guide bar when you make the second notch.

2. Make the felling cut (28) no less than 2 in. (50 mm) or higher than the level notching cut. Make sure that this cut:
   a) Is parallel to the level notching cut.
   b) Keeps sufficient wood 2 in. (50 mm) or 1/10 the diameter of the tree to become a hinge (29) which prevents the tree from twisting and felling in the wrong direction.
   When the felling cut (28) gets near the hinge (29), the tree falls. Stop the felling cut of the tree:
   • Does not fall in the correct direction or
   • Moves backward, causing the cutting bar and chain to become stuck in the cut.

3. Use a felling wedge to open the cut and let the tree fall in the correct direction.

4. When the tree starts to fall:
   a) Remove the chainsaw from the cut.
   b) Stop the machine.
   c) Put the machine down.
   d) Move away from the tree via the escape path (25).
   Always keep watching the tree to see the direction of fall. Be careful with overhead branches and your footing.

9.6 LIMB A TREE

Limbing is the removal of branches from a fallen tree.

1. Keep the larger lower branches to hold the log off the ground (31).
2. Remove the small limbs (30) in one cut.
3. Limb the branches with tension from the bottom to the top.
4. Keep the larger lower branches as support until the log is limbed.

9.7 BUCK A LOG
To buck is to cut a log into lengths.

CAUTION
Do not let the chainsaw touch the ground.

It is important to make sure your footing is secure and your weight is evenly distributed. If possible, lift the leg and hold it with branches, logs or chock. Obey the instructions below:

When the log is held along the full length (32), cut it from the top (33).

When the log is held on one end (34):

1. Cut the first time 1/3 of the diameter from the bottom (35).
2. Cut the second time from the top (36) to complete the bucking.

When the log is held on two ends (37):

1. Cut the first time 1/3 of the diameter from the top (36).
2. Cut the second time lower 2/3 from the bottom to complete the bucking (35).

When the log is on a slope:

1. Stand on the uphill side.
2. Control the chainsaw completely.
3. Hold the chainsaw handles tightly.
4. Release the cutting pressure near the end of the cut.

When bucking is complete (38):

1. Wait for the chain to stop (39).
2. Ensure the chainsaw is turned off.
3. Check for hazards before you move to another tree.

MAINTENANCE

CAUTION
Do not let brake fluids, gasoline, or petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.
CAUTION
Do not use strong solvents or detergents on the plastic housing or components.
WARNING
Remove the battery pack from the machine before maintenance.

10.1 REPLACE THE GUIDE BAR AND THE CHAIN

1. Loosen the chain cover by turning the chain cover knob counterclockwise.

2. Remove the chain cover.

3. Put the chain drive links (21) into the bar groove (20).

4. Put the chain cutters (22) in the direction of the chain operation.

5. Put the chain in position and make sure that the loop is behind the guide bar.

6. Hold the chain and bar.

7. Put the chain loop around the sprocket (17).

8. Make sure the chain tension pinhole (19) on the guide bar fits correctly with the bolt (16).

9. Install the chain cover.

10. Tighten the chain. Refer to Adjust the chain tension.

11. Tighten the chain cover knob when the chain is correctly tensioned.

NOTE
If you start the chain saw with a new chain, have a test for 2-3 minutes. A new chain gets longer after the first use, examine the tension and tighten the chain if necessary.

10.2 ADJUST THE CHAIN TENSION
The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.
Tension the chain so that it can only just be pulled away from the bar at its center point.

WARNING
A slack chain may jump off and cause serious or even fatal injury.

CAUTION
Wear protective gloves if you touch the chain, bar, or areas around the chain.

1. Stop the machine.

2. Loosen the chain cover by turning the chain cover knob counterclockwise.
   NOTE
   It is not necessary to remove the chain cover to adjust the chain tension.

3. Turn the chain tension knob clockwise to increase the chain tension.

4. Turn the chain tension knob counterclockwise to decrease the chain tension.

5. When the chain is at the wanted tension, tighten the chain cover.

**NOTE**
During normal saw operation, the temperature of the chain increases. The drive links of a correctly tensioned warm chain will hang approximately 1/16 in. (1,58 mm) out of the
bar groove.

10.3 SHARPEN THE CUTTERS
Sharpen the cutters if the chain does not go into the wood easily.
NOTE
We recommend that a service center, which has an electric sharpener, perform important sharpening work.

1. Clamp Bar.

2. Sharpen the cutter’s corner with a 5/32 in. (4 mm) diameter round file.

3. Sharpen the top plate, side plate, and depth gauge with a flat-file.

4. File all the cutters to the specified angles and the same length.

NOTE
During the process:

• Keep the file flat with the surface to be sharpened.
• Use the midpoint of the file bar.
• Use light but firm pressure when sharpening the surface.
• Lift the file away on each return stroke.
• Sharpen the cutters on one side and then move to the other side.

Replace the chain if:

• The length of the cutting edges is less than 1/5 in. (5 mm).
• There is too much space between the drive links and the rivets.
• The cut speed is slow.
• Sharpening the chain many times but it does not increase the cutting speed. The chain is worn.

10.4 GUIDE BAR MAINTENANCE

NOTE
Make sure that the bar is turned over periodically to keep symmetrical wear on the bar.

1. Lubricate the bearings on the nose sprocket (if present) with the syringe (not included).
2. Clean the bar groove with the scraping hook (not included).
3. Clean the lubrication holes.
4. Remove burr from the edges and level the cutters with a flat-file.

Replace the bar if:

• the groove does not fit with the height of the drive links (which must never touch the bottom).
• the inside of the guide bar is worn and makes the chain lean to one side.

TRANSPORTATION AND STORAGE

Before you move the machine, always

• Remove the battery pack from the machine.

• Keep hands clear of the lock-out button.

• Put the scabbard on the guide bar and the chain.
  Before you put the machine into storage, always

• Remove all residual oil from the machine.

• Remove the battery pack from the machine.

• Clean all unwanted material from the machine.

• Make sure that the storage area is
  • Not available to children.
  • Away from agents which can cause corrosion, such as garden chemicals and de- icing salts.

TROUBLESHOOTING

Problem

| Possible cause|

Solution

---|---|---
The guide bar and the chain become hot and release smoke.| The chain is too tight.| Adjust the chain tension.
The oil tank is empty.| Add oil.
Contamination causes a blockage of the discharge port.| Remove the guide bar and clean the discharge port.
Contamination causes a blockage of the oil tank.| Clean the oil tank. Add the new oil.
Contamination causes a blockage of the guide bar and the oil tank cap.| Clean the guide bar and the oil tank cap.
Contamination causes a blockage of the sprocket or guide wheels.| Clean the sprocket and the guide wheels.

Problem

| Possible cause|

Solution

---|---|---
The motor runs but the chain does not rotate.| The chain is too tight.| Adjust the chain tension.
The guide bar and the chain are damaged.| Replace the guide bar and the chain if it is necessary.
The motor is damaged.| 1. Remove the battery pack from the machine.
2. Remove the guide bar cover.
3. Remove the bar and saw chain.
4. Clean the machine.
5. Install the battery pack and operate the machine.If the sprocket rotates, it means the motor works prop- early. If not, call the service center.
The motor runs and the chain ro- tates, but the chain does not cut.| The chain is blunt.| Sharpen or replace the saw chain.
The chain is in the incorrect direction.| Turn the chain loop in the other direction.
The chain is tight or loose.| Adjust the chain tension.

TECHNICAL DATA

The recommended ambient temperature range:

Item

|

Temperature

---|---
Appliance storage temperature range| 32°F (0°C) – 113°F (45°C)
Appliance operation temperature range| 32°F (0°C) – 113°F (45°C)
Battery charging temperature range| 39°F (4°C) – 104°F (40°C)
Charger operation temperature range| 39°F (4°C) – 104°F (40°C)
Battery storage temperature range| 32°F (0°C) – 113°F (45°C)
Battery discharging temperature range| 32°F (0°C) – 113°F (45°C)

LIMITED WARRANTY

3 YEARS LIMITED WARRANTY

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts, or workmanship.
Greenworks, at its own discretion, will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units that have been used for personal use that has not been purchased or rented for industrial/commercial use, and that have been maintained in accordance with the instructions in the owners’ manual supplied with the product when new.

ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.

HELPLINE:
Warranty service is available by calling our toll-free helpline at 1-888-909-6757.

TRANSPORTATION CHARGES:
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks.

EXPLODED VIEW

No .

| Part No.| Qty| Description| No .| Part No.| Qty|

Description

---|---|---|---|---|---|---|---
1| R0201248-00| 1| Bar / Chain| 6| R0201251-00| 1| Bucking Spikes
2| R0201229-00| 1| Chain Tension Knob| 7| R0201252-00| 1| Side Cover Assembly
3| R0201249-00| 1| Sprocket Kit| 8| R0201253-00| 1| Auxiliary Handle Kit
4| R0201084-00| 1| Oil Cap Assembly| 9| RB34114155V1| 1| Scabbard
5| R0201250-00| 1| Hand Guard| | | |

References

• Greenworks Outdoor Power Equipment, Lawn & Garden Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>