Pyle Bluetooth Marine Receiver Stereo – 12v Single DIN-Complete Features/Owner’s Guide

Pyle Bluetooth Marine Receiver Stereo – 12v Single DIN

Specifications

• BRAND: Pyle
• CONNECTIVITY TECHNOLOGY: Bluetooth
• SUPPORTED INTERNET SERVICES: Pandora
• ITEM DIMENSIONS LXWXH: 1.97 x 4.26 x 7.01 inches
• OUTPUT WATTAGE: 75 Watts
• COMPATIBLE DEVICES: Speaker
• ITEM WEIGHT: 1.33 Pounds
• AUDIO ENCODING: Stereo
• CONTROL METHOD: Remote.

Introduction

With this Pyle 12v marine radio receiver, you may listen to music while staying afloat. It has a peak power output of 300 Watts (75W x 4) and an EQ configuration that allows you to manage the bass, treble, balance, and fader for a high-quality sound. It has a Bluetooth connection. With the help of this receiver, you may stream audio directly from your hand-held A2DP Bluetooth- enabled devices, such as an iPhone, Android smartphone, iPad, or tablet, and listen to internet radio services like Pandora through your speakers.

The phone number is displayed in the LCD panel digital display of this boat’s in-dash console audio receiver, which has a built-in mic for answering calls. Has a call answer/end button as well as a redial function for the last number dialed. The front panel of these 12 volts easy to mount head unit console receiver system has a digital LCD with crisp button and knob controls, Aux-in, USB / SD slot, and AM FM radio. There are also RCA line-out jacks at the back. This black marine radio replaces single din size radios with a single DIN universal standard size design. Power and wiring harness, metal chassis frame bracket, outside trim frame cover, and remote control are all included in the kit.

To Install the Ship/Car Receiver

Be sure to first test all connections and then follow these steps to install this unit.

1. Make sure the ignition is turned off and then disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Disconnect the wire harness and the antenna.

3. Lift the left or right top corner of the plastic outer trim ring then pull it out to remove it.

4. Insert the two bracket keys into the left and right side of the chassis, as shown
   

5. Insert the mounting sleeve into the dashboard and bend the mounting tabs out with a screwdriver.
   Make sure that the lock lever is flush with the mounting sleeve and that it does not project beyond it.

6. Insert this receiver into the mounting sleeve.

7. Connect wires as illustrated in the “Wiring Diagram.”

8. Install the plastic outer trim ring.

Wiring connections

Removal of the Main Unit

1. Remove the plastic trim from the main unit.
2. Insert a bracket key into the left and the right sides of the main unit and draw the unit out of the mounting sleeve.

Control Buttons and Functions

1. (power)/MODE (source) button
2. SEL (select/menu) button and VOL (volume) knob
3. Button, BAND (band) button AMS (automatic store / preset station scan, automatic music search) button
4. (pause/play), Preset station 1 button
5. INT (intro), Preset station 2 button
6. RPT (repeat), Preset station 3 button
7. RDM (random), Preset station 4 button
8. -10(previous 10 tracks), Preset station 5 button
9. +10(next 10 tracks), Preset station 6 button
10. CLK (clock setting) button, button
11. (tune down, seek down, previous track, fast reverse) button
12. (tune up, seek up, next track, fast forward) button
13. MUTE button
14. IR remote control sensor
15. LCD Display
16. USB port & Micro SD Card Slot
17. MIC hole (built-in Microphone)
18. AUX IN (auxiliary input) jack
19. RESET button

Turn Unit On/Off

• Press the power button /MODE button on the front panel to turn on the unit, and long press it again to turn off the unit.
• Press the power button on the remote control to turn the unit on or off.

Adjust Volume (VOL)

Rotate the VOL knob on the front panel or press the VOL+ /VOL- button on the remote control to increase or decrease the volume level.

Adjust Menu Options (SEL)

• Press the SEL button on the front panel or on the remote control repeatedly to cycle through the following adjustable audio functions: BASS,TREBLE, BALANCE, FADER, EQ OFF/ CLASS/ ROCK/POP/FLAT/, LOUD ON/OFF, DX/LOC, STEREO/MONO, CLOCK 12/24 and AREA US/EU.

• Rotate the VOL knob on the front panel or press the VOL+ /VOL- button on the remote control to adjust the selected item.

•  BASS: -07, -06, ~, -01,00, +01, ~, +06, +07

•  TREBLE: -07, -06, ~, -01,00, +01, ~, +06, +07

•  BALANCE: L07, L06, ~, L01, 00, R01, ~, R06, R07

•  FADER: R07, R06~, R01,00, F01, ~, F06, F07

•  EQ(Equalizer) Setting: OFF, FLAT, POP, ROCK, CLASS

•  Loudness: LOUD ON/OFF

•  DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).

•  Stereo/Mono: Switches between MONO and STEREO reception mode for radio frequencies.

•  CLOCK 12/24: Select between 12 hours and 24 hours display.
  Note : If 12-hour display is selected, AM= Morning; PM= Afternoon

•  AREA US/EU: This receiver is equipped the USA / Europe frequency.

• Rotate the volume knob to switch between USA and Europe frequency.

• Rotate the VOL knob on the front panel or press the VOL+ /VOL- button on the remote control to adjust the selected item.

Set the Clock (CLK)

1. To display clock time, press the CLK button.
2. To set clock time, press and hold the CLK button and the hour will flash.
3. Press the or button on the front panel or on the remote control to adjust the hour.
4. Press the CLK button and the minutes will flash.
5. Press the or button on the front panel or on the remote control to adjust the minute.

Change the Source (MODE)

• Press the MODE button to switch between RADIO, BT(Bluetooth), USB (with USB device inserted), CARD (with SD card inserted), and AUX-IN (auxiliary input) modes.

Mute on/off

• In power-on mode, briefly press the MUTE button to toggle mute on or off. The muted state will be also released when the volume knob is used.

Loudness on/off

• Press the LOUD button on the remote control to turn on the loudness to reinforce the output of bass frequencies, and press again to turn it off.

Preset Equalizer (EQ)

• Press the EQ button on the remote control to toggle between EQ OFF, ROCK, POP, CLASS, and FLAT. USB port, Micro SD Card Slot
• The USB port and Micro SD card slot of this receiver is designed for media playback from flash memory devices and micro SD.

Built-in Microphone

• To receive your voice when you call by using this Bluetooth hands-free system.

Aux input connector

• The 3.5mm auxiliary input stereo connection is designed for devices with 3.5mm line-out or headphone output.

Reset System (RESET)

• The RESET button is used to reset all parameters to factory default settings.
• This function may be used when the LCD does not display normally or sound is distorted, or when any of the controls are disabled. Use a thin object with a pointed end to depress the RESET button.

USB / SD CARD OPERATION

To insert USB / SD CARD

• To play files on a USB device, open the USB port cover and insert the USB storage device into the
• USB port. Playback will begin automatically.
• Insert micro SD card into the micro SD slot. Playback will begin automatically.

Eject USB/SD

• To eject a USB device, press the button to stop playback, then remove the USB device.
• To eject an SD card, press the button to stop playback, and puss the SD card in the slot, then remove the micro SD card from the micro SD card slot.

Play/Pause

• Press the (play/pause) button to pause or resume playback.

Next/Previous Track

• To play the next track, press the button. To play the previous track, press the button.

Fast Forward/Backward

• To fast forward, press and hold the button. To fast backward, press and hold the button.

Introduction Scan

• Press the INT button to play the first 10 seconds of each track, press again to stop the introduction scan, and play the current track.

Repeat The Same Track

• Press the RPT button to repeat the current track. Press again to stop repeat playback and resume normal playback.

Playing all tracks in random

• Press the RDM button to play all tracks in random order, press again to cancel this function.

Track/Folder Navigation

• In USB or SD card mode, press the 5/-10 button to go backward 10 tracks.
• Press the 6/+10 button to jump forward 10 tracks.
• In MP3, USB or SD card mode, press and hold the 5/-10 button to go back the previous folder.
• Press and hold the 6/+10 button to go to the next folder.

Repeat this function depending on the number and level of folders.

• These buttons have no function if the USB device or SD card has no folders.
• Select the track or file for playback in MP3 format
• Press and hold the AMS button to direct select a music file. The “TRK0000” will appear on the display.
• Turn the volume control to select the “first number”. Then press the button to move the “first
• number” to the left and enter the next number. When the desired track number appears, confirm your
• selection by pressing SEL button.

AUXILIARY INPUT OPERATION

• This receiver is equipped with an external auxiliary input jack (3.5mm) on the front panel which is
• compatible with audio output from an MP3 music player.
• Plug such a player into the AUX IN jack with a 3.5mm stereo audio cable and press the MODE button to
• switch to AUX input mode. “AUX IN” appears in the display. Listen to music from an external device
• through the speaker.

Note
Adjust the volume of the external device to a comfortable level with the receiver volume control.

BLUETOOTH OPERATION

Pair and Connect

Prior to using the Bluetooth device as a hands-free system for a Bluetooth- enabled mobile phone for the first time, you must pair and connect the two devices as follows:

1. In any mode, prior to pairing and connecting, the BT logo in the LCD indicating that no device is connected. To begin pairing, enable BT mode on your mobile phone.
2. When the phone finds this ship/car audio system, the “PYLE” name will be displayed.
3. Choose the “PYLE” from the device list to pair and connect with this ship/car audio system. Upon confirming, the BT logo will stop flashing.
4. When pairing is complete, the mobile phone audio will automatically transfer to the ship/car audio system whenever a call is made or received, or when the mobile phone plays music.

Make a Call

To make a call, dial the call directly from the paired mobile phone. To make a call with this Bluetooth hands-free system:

1. When linking up the Bluetooth-enabled mobile phone to this Bluetooth hands-free system, press the button to access the dial telephone number mode, then press the “0~9”, * and # button on the remote control to input the telephone number, and the entered number will be shown on the LCD display.
2.  If a number has been incorrectly inputted, press the DEL button or button to delete it
3. Press the button to make the outgoing call.

Redial Last Dialed Number

• Press and hold the button on the control panel to redial the last dialed phone number.

Answer a Call

• When the mobile phone is called, the incoming telephone number displays on the LCD.
• To receive the call, press the button on the control panel.

Reject a Call

• To reject the call, press the button on the control panel.

End a Call

• To end an active call, press the button.
• Switch Audio Between Bluetooth hands-free system and Mobile Phone
• During a call, press the VOL knob/button to switch the audio source from this Bluetooth hands-free audio
• system back to your mobile phone.

Adjust Talk Volume

• During a call, use the VOL knob or VOL+ /VOL- button to adjust the volume level.
• Use the MUTE button to mute the sound.

Audio Streaming (A2DP)

1. Press the /MODE button to enter BT mode and display pause in the LCD display.
2. When a mobile device is paired, music played through that device will automatically be heard through this Bluetooth hands-free audio system.
3. Press the or button to play the next or previous song on the mobile phone.
4. Press the button to pause or resume music playback.

Remove Insulating Sheet

The remote control comes with an insulating sheet attached to the underside of the remote control, as illustrated on the right. The remote control will not work until the insulating sheet is removed.

Replace Lithium Battery Cell

1. When the lithium cell battery becomes weak, replace it as illustrated on the right.
2. Press and hold the movable block in the direction indicated by arrow 1. At the same time, pull the cell holder out of the remote control in the direction indicated by arrow 2.
3. Replace the old cell with a new one, making sure the (+) polarity is facing upward.
4. Re-insert the cell holder into the remote control.

CONTROLS OF REMOTE

Button Names and Locations

1. (Power on/off) button
2. VOL+/VOL-(volume increase/decrease) button
3. Band button, (answer call) button
4. Tune down, seek down; Previous track, fast reverse
5. SEL(selection) button
6. Tune up, seek up; Next Track, fast forward
7. Mute button, DEL(Delete) button
8. CLK(clock setting) button, (end call) button
9. Preset station 1 button, keypad 1
10. INT (intro) button, preset station 2 button, keypad 2
11. RPT (repeat) button, preset station 3 button, keypad 3
12. RDM (random), preset station 4 button, keypad 4
13. -10(previous 10 tracks), preset station 5 button, keypad 5
14. +10(next 10 tracks), preset station 6 button, keypad 6
15. ST (stereo) button, keypad 7
16. LOUD (loudness) button, keypad 8
17. AMS (automatic music search) button, keypad 9
18. MODE button, keypad *
19. EQ(Equalizer) button, keypad 0
20. LOC (local)/DX button, keypad #

Frequently Asked Questions

• What is the procedure for connecting my Pyle Bluetooth receiver?
  When you press the BT/Line button on the front panel, you’ll hear the voice “POWER ON” and “PAIRING,” and the unit will be ready to link with your external device immediately.

• How good are Pyle stereos?
  It performs admirably, is really loud, and is simple to operate. I would have given it five stars if it didn’t have a small buzz at low volumes, which my previous receiver did not have. It doesn’t pick up many radio stations, but because I prefer to use the aux, this isn’t an issue.

• What is the best way to connect my Bluetooth device to my Pyle amplifier?
  When you press the BT/Line button on the front panel, the voice “POWER ON” and “PAIRING” will be heard, and the unit will be ready to pair with your external device automatically.

• Why isn’t my Bluetooth speaker working?
  If your Bluetooth devices are out of range or not in pairing mode, they may be unable to connect. If you’re having trouble with Bluetooth, try restarting your devices or setting them to “forget” the connection.

• What are the pros and cons of Pyle Bluetooth receivers?
  The speaker amp performs admirably; it produces high-fidelity audio, and the Bluetooth connection, even from a few rooms away, is excellent. The remote is a fantastic feature, and the LCD is clear and legible.

https://m.media-amazon.com/images/I/811CWa0OT+L.pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>