behringer CM1A MIDI to CV Converter Module for Eurorack User Guide
- June 5, 2024
- Behringer
Table of Contents
CM1A MIDI to CV Converter Module for Eurorack
CM1A MIDI to CV Converter Module for Eurorack
User Guide
CM1A
MIDI to CV Converter Module for Eurorack
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances, and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston Microphones, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
CM1A
Controls
- USB – Connect to a computer to transmit MIDI control signals to the CV and Trig outputs. The module can also receive firmware updates via this connection.
- MIDI IN – Connect a MIDI controller to transmit signals to the CV and Trig outputs.
- MIDI THRU – Pass the signals received at the MIDI In jack to other devices.
- CV – Send control voltages received via USB or MIDI to other modules.
- TRIG – Send trigger signals received via USB or MIDI to other modules.
- TRIG MODE – Selects whether the Trig outputs function as V-trig or S-Trig. In the middle position, the upper output functions as S-trig, and the lower output functions as V-trig.
Mode Select
A button on the rear panel allows the CM1A to be configured for use with
various synth families offered by Behringer. The first LED indicates whether
the CV range is optimal for System 15/35/55 or System 100/2500 series modules.
The second LED indicates monophonic or duophonic operation.
Press the button quickly to switch the CV range, or press and hold to switch
between monophonic and Dubophonic.
| Mode | LED colors | Operation |
|---|---|---|
| Mode 1 | Red/red | System 15/35/55 CV range, monophonic |
| Mode 2 | Green/red | System 100/2500 series CV range, monophonic |
| Mode 3 | Red/green | System 15/35/55 CV range, duophonic |
| Mode 4 | Green/green | System 100/2500 series CV range, duophonic |
SYNTHRIBE
Download the SYNTHRIBE application from behringer.com to adjust pitch bend
range, select MIDI channel and CV mode, and adjust note range (C0 to C9), and
do other calibration.
Power Connection
The unit comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.
- Turn the power supply or rack case power off and disconnect the power cable.
- Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
- Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
- After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.
Installation
The necessary screws are included with the module for mounting in a Eurorack
case. Connect the power cable before mounting. Depending on the rack case,
there may be a series of fixed holes spaced 2 HP apart along the length of the
case, or a track that allows individual threaded plates to slide along the
length of the case. The free-moving threaded plates allow precise positioning
of the module, but each plate should be positioned in approximate relation to
the mounting holes in your module before attaching the screws.
Hold the module against the Eurorack rails so that each of the mounting holes
are aligned with a threaded rail or threaded plate. Attach the screws partway
to start, which will allow small adjustments to the positioning while you get
them all aligned. After the final position has been established, tighten the
screws down.
Specifications
Outputs
CV
| Type | 2 x 3.5 mm TS jack, DC-coupled |
|---|---|
| Impedance | 1000 |
| Max output level | -6.3 V to +10 V |
| CV range, System 100, 2500 series mode | -1 V to +9 V,1 V/octave |
| CV range, System 15, 35, 55 mode | -5.3 V to +4.7 V,1 V/octave |
| CV modes | Monophonic, duophonic |
Trig
Type| 2 x 3.5 mm TS jack, DC-coupled
Impedance| 250
Max output level| +5 V when in V-Trig mode, S-Trig = pull down to 0 V
Trig modes| V-Trig, S-Trig, both: upper = 5-Trio, lower = V-Tria
MIDI
| Type | 2 x 5-pin DIN |
|---|
MIDI IN and MIDI THRU
MIDI Channel (1 to 16) set via SynthTribe tool
USB
| Type | USB 2.0, Type B |
|---|
Mode select (rear panel)
Mode 1, underside
LEDs = red/red| System 15, 35, 55
CV range, monophonic
---|---
Mode 2, underside
LEDs = green/red| System 100, 2500 series
CV range, monophonic
Mode 3, underside
LEDs = red/green| System 15, 35, 55
CV range, duophonic
Mode 4, underside
LEDs = green/green| System 100, 2500 series
CV range, duophonic
Power
| Power supply | Eurorack |
|---|---|
| Current draw | 70 mA (+12 V), |
10 mA (-12 V)
Physical
| Dimensions | 30 x 129x 520 mm (1.18 x 5.08 x 20.47″) |
|---|---|
| Rack units | 6 HP |
| Weight | 0.09 kg (0.19 lbs) |
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
| Responsible Party Name | Music Tribe Commercial NV Inc. |
|---|---|
| Address: | 5270 Procyon Street, Las Vegas NV 89118, United States |
| Phone Number: | +1 702 800 8290 |
CM1A
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU, Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC. The full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17,
DK – 8200 Aarhus N, Denmark
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>