Mytee 240-120 Hot Turbo User Manual
- June 5, 2024
- MYTEE
Table of Contents
**Mytee 240-120 Hot Turbo
**
**Safety Information
**
Grounding Instructions This machine must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electrical shock. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug mustbe plugged into an appropriate outlet that is properly installed in accordance with all local codes and ordinances. Do not remove the ground pin; if missing, replace the plug before use. Improper installation of the equipment-grounding conductor can result in a risk of electric shock. Be sure to check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. If the plug will not fit in the outlet do not modify the plug or the machine’s cord, instead have a proper outlet installed by a qualified technician. This machine is for use on a nominal 120-volt circuit and with a grounding plug similar to the one in Figure 1 below. If a proper outlet is not available, follow the illustrations in Figures 2 & 3 to install a temporary- grounding plug. This temporary workaround should be used only until a proper outlet (Figure 1) can be installed by a qualified electrician. When and if this type of adapter is employed, screw the adapter’s extended tab into place with a metal screw. However, grounding adapters are not approved for use in Canada. Again, be sure to check the grounding pin for damages and replace if necessary. The Green, or Green-Yellow, wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to only the grounding pin.
Parts and Service
Please contact Mytee service personnel or a Mytee authorized Service Center
using Mytee’s original replacement parts and accessories if repairs need to be
performed. When and if calling tee for support, please have your Model and
Serial Number available for faster assistance.
Name Plate
The Model and Serial Number are located on the lower half of the back of the
machine near the power plug and will be required for ordering replacement
parts. You can use the space provided in this manual to note down both for
future reference.
Unpacking the Machine
When your new machine is delivered, please carefully inspect both the shipping
carton and the machine for damages. If damage is evident, save both the
shipping carton and machine so that the delivering carrier can inspect it.
Contact the carrier immediately to file a freight claim if there has been any
damage.
Caution and Warnings Symbols
Mytee uses the symbols below to signal potentially dangerous conditions.
Always read this information carefully and take the necessary steps to protect
personnel and property. Is used to warn of immediate hazards that will cause
severe personal injury or death. Is used to call attention to a situation that
could cause severe personal injury. Is used to call attention to a situation
that could cause minor personal injury or damage to the machine or other
property. When using an electrical appliance, basic precautions should always
be followed, including the following: Read all instructions before using this
machine. This product is intended for commercial use only
Safety Information
To reduce the risk of fire, electrical shock, or injury:
-
Read all instructions before using the equipment.
-
Use only as described in this manual. Use only the manufacturer’s recommended attachments.
-
Always unplug the power cord from the electrical outlet before attempting any adjustments or repairs.
-
Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
-
Do not pull or carry by a cord. Do not close a door on cord or pull the cord around sharp edges or corners.
-
Do not run appliance over cord. Keep cord away from heated surfaces.
-
Do not use with a damaged cord or plug. If the cord is damaged, repair it immediately.
-
Do not use outdoors or on wet surfaces and/or standing water.
-
Always unplug or disconnect the appliance from the power supply when not in use.
-
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
-
Do not use in areas where flammable or combustible material may be present.
-
Do not leave the unit exposed to harsh weather elements. Temperatures below freezing may damage components and void a warranty.
-
Use only the appropriate handles to move and lift the unit. Do not use any other parts of this machine for this purpose.
-
Keep hair, loose clothing, fingers, and all parts of the body away from all openings and moving parts.
-
Use extra care when using on stairs.
-
To reduce the risk of fire or electric shock, do not use this machine with a solid-state speed control device.
-
The voltage and frequency indicated on the nameplate must correspond to the wall receptacle supply voltage.
-
When cleaning and servicing the machine, local or national
regulations may apply to the safe disposal of liquids that may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids. -
Do not leave operating unattended.
Technical Specifications
| Max. Pressure | 1,500 PSI |
|---|
Max.
Temperature
| 210º F
Max. Wattage| 2,400 W (4x 600 W)
Power Cord| Single 25’ 12/3
Amp Draw| 5 amps per switch @ 115V
2.5 amps per switch @ 230V
Product Weight| 26 lbs.
Product
Dimensions
| 11.5” x 12.5” x 11”
| Max. Pressure | 1,500 PSI |
|---|
Max.
Temperature
| 210º F
Max. Wattage| 4,800 W (4x 1,200 W)
Power Cord| Dual 25’ 12/3
Amp Draw| 10 amps per switch @ 115V
5 amps per switch @ 230V
Product Weight| 30 lbs.
Product
Dimensions
| 11.5” x 12.5” x 11”
Product Features
- carrying Handle
- Switch Plate
- Input Hose with Male Quick Connect
- Output Female Quick Connect Fitting
- Power Cord(s)
Machine Operation
Powering the Mytee Hot Turbo
Plug the power cord(s) into the appropriate outlet(s). For dual cord units, plug the two cords into two separate circuits. The indicator light will turn on when this is done.
Connecting to Extractor/Truckmount
Connect the input hose to your extractor or truck mount. A longer solution hose can be used between the Mytee Hot Turbo and the extractor if necessary. Connect a solution line from the output connection to your cleaning tool.
Operation
In order to avoid vapor lock, the extractor/truck-mount and Mytee Hot Turbo should be switched on by following the procedure below after a cleaning tool is connected:
- Activate the pump on your extractor or Pull the lever on the cleaning tool to release air in the line. Hold the lever until a steady flow of water comes out of the tool.
- Once the pump is primed and there is pressure in the solution line, turn on however many heaters on the Mytee Hot Turbo you are using and wait a few minutes for the water to heat
- Once water is heated, turn on the vacuum and begin cleaning.
Machine Maintenance
| Maintenance Item | Daily | Weekly |
|---|---|---|
| Clean and inspect hoses and fittings. | X | |
| Check power cable. | X |
Clean machine with all-purpose cleaner
and cloth.
| X|
Flush solution system with Mytee
System Maintainer
| | X
System Maintainer
Regular flushing of the solution system with Mytee System Maintainer keeps your extractor running efficiently by removing hard water scaling that builds up in the system.
How to use System Maintainer:
-
1. 1. Thoroughly mix System Maintainer with warm water at a 1:1 ratio in a separate Pour into your extractor’s solution tank.- Connect the Mytee Hot Turbo to the extractor and connect a cleaning tool to the Mytee Hot
- Turn on the extractor’s pump and run the System Maintainer solution through the Mytee Hot Turbo and into a bucket or receptacle until you have a solid
- Let sit for about 5 minutes while the System Maintainer solution
- Finish running the rest of the solution through the Run clean water through the system to flush out any remaining System Maintainer.
-
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>